1978 Buick LeSabre Performance Engines

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
• Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
• Raises combustion sealing force to roughly three times that of standard head gaskets.
• Steel wire rings for the greatest combustion seal strength.
• Not intended for use in emission controlled vehicles.

Product Features:

• Designed for Optimum Torque and Acceleration
• Maximum Performance From Idle through Mid-Range
• Matched To Performer Intake PN[5486]
• Includes Hydraulic Lifters and Assembly Lube
• Major Improvement in Throttle Response and Torque
• Use For Daily Drivers/Trucks/Vans/RVs/4x4s
• Take The Guesswork Out Of Camshaft Selection

Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:

• Precision Machined
• Case Hardened
• Give Accurate Alignment
• 2 Per Set

Magnum Pushrods from COMP Cams offer an affordable solution for your .080″ wall chromemoly pushrod needs. Designed to withstand the stresses of a high performance engine, Magnum Pushrods are head-treated for extended durability and have precision formed, reinforced ends. Magnum Pushrods are black-oxide finished with their part number and length laser etched onto the surface for easy identification.

Product Features:

• 3/8″ Diameter, 7.800″ Length
• Magnum Pushrods for Small Block Chevy
• One-piece .080″ wall chromemoly steel tubing
• Heat-treated for extended durability and guide plate compatibility
• Precision formed and reinforced pushrod end

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
• Not intended for use in emission controlled vehicles.

Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.

Product Features:

• Chrome plated
• Grade 8
• 12-point head
• AN washers with no exposed shoulder for a professional appearance

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Product Features:

• Use W/ Valve Springs Part #5703, 5794
• Set of 16
• 1.50 in. Outside Diameter
• Steel Material
• Black Oxide Finish

This Mr. Gasket Water Pump Bolt Set includes chrome plated grade 5 hex head fasteners to install the water pump on your small or big block Chevrolet with the long style water pump. Includes four 3/8 inch-16 x 2 inch bolts with four 3/8 inch AN washers. AN washers have no exposed shoulder which offers a professional appearance.

Product Features:

• Chrome Plated
• Grade 5
• AN washers with no exposed shoulder for a professional appearance

Product Features:

• For Idle to 5500 RPM Street-Driven Performance
• Dual-Plane Low-Rise Intake w/180 Deg Firing Order
• Patented Runner Design Ensures Broad Torque Curve
• Excellent Throttle Response and Mid-Range Power
• 50-State Street Legal if Correct Carburetor Used
• Accepts Late-Model Choke; Waterneck; and HEI
• Accepts A/C And Alternator
• Accepts Exhaust Heated Chokes and Accepts EGR

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Steel core gasket construction
• Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
• Not intended for use in emission controlled vehicles.

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods, the Thumpr series’ early i

Product Features:

• Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
• Best with aftermarket converters and more rear gear.
• Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
• With steel core to provide ultimate excellent blowout resistance.
• Not intended for use in emission controlled vehicles.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
• With steel core to provide ultimate excellent blowout resistance.
• Not intended for use in emission controlled vehicles.

Torque Converter – Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New allow steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required.

Product Features:

• New Precision Pump Drive Tube
• Pressure Tested
• Fully Balanced
• Needle Thrust Bearing
• New Thrust Washer
• Washer Between Turbine and Cover

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
• Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
• Not intended for use in emission controlled vehicles.
• Not intended for use in emission controlled vehicles.

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:

• Repairs That Leaky Rear Main Sail
• Silicone Rubber to Withstand Extreme Engine Oil Temperatures
• Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
• Injection Molded for Precise Fit

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

• Manufactured from cellulose/nitrile composition gasket material.
• Provides excellent sealing and durability.
• Can be trimmed if necessary for modified port applications.
• Complete with manifold end seals and distributor gasket.
• For OE replacement, high performance street, drag race and oval track use.

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 180 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:

• Black Oxide Coated Grade 8 Steel
• Kit Contains 16 Studs
• Easy To Install
• Heat Treated Steel
• Prevents Stud Flexing
• Black Plated Finish

These COMP Cams Ultra-Gold Aluminum Roller Rocker Arms with a 3/8″ stud diameter and 1.6 ratio are designed for Chevrolet V8 265-400 applications. The new modern design features of these Ultra-Gold Rockers are proven to withstand extremely aggressive spring pressure and valve lift. Designed specifically for high performance street and race engines, the Ultra-Gold Aluminum Rocker Arms are precision CNC-machined to strict tolerances. Developed to meet the demands of professional engine builders, these rockers include features never before possible in an aluminum rocker arm.

Product Features:

• CNC-machined, lightweight design removes weight and yields unrivaled quality and ratio accuracy
• Designed for high performance street and race engines
• Precision-sorted trunion bearings withstand elevated valve spring pressure and valve lift
• Additional clearance, up to 1.650″ O.D. valve spring

Product Features:

• Timing Chain Only

With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:

• Advance the cam for increased torque and horsepower
• Tune your powerband for more end torque or increase top end horsepower
• Includes (4) offset bushings and (1) 0 degree bushing
• Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
• Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
• Increase Top-End Horsepower

Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:

• Complete with o-rings and mounting bolts
• Features an o-ring style seal to prevent water leaks
• Chrome plated
• 1/2″ NPT port can be used for various coolant temp related sensors or switches

Spectre’s Chevrolet late model water neck offers the normal angled water neck and a 1/2 inch NPT threaded hole for a by-pass hose. This water neck has a chrome plated finish for a lasting look great and includes the bolts.

Product Features:

• Fits Chevy engines
• Includes a 1/2 inch NPT threaded hole for by-pass hose
• Includes bolts
• Chrome plated
• Easy to install
• O-ring/gasket not included

Spectre’s Oldsmobile V8 water neck fits Oldsmobile 330, 350, 425 and 455 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck has an additional by-pass hose connection and includes the bolts.

Product Features:

• Fits Oldsmobile 330, 350, 425 and 455 engines
• Chrome plated
• Bolts included
• Designed for OEM fit
• Easy to install
• O-ring/gasket not included