1976 Dodge W100 Drivetrains
More 1976 Dodge W100 Drivetrains Categories
If you’re looking for an original Drivetrains replacement for a 1976 Dodge W100, you can search through our selection below. You’ll also find aftermarket and OEM Drivetrains to meet your needs.
Essential 1976 Dodge W100 Drivetrains
Motive Gear – Differential Carrier (Part No.C9.25E)
Yukon Gear – Crush Sleeve (Part No.33094)
from
$15.99
Crush Sleeve for Chrysler 8″ & 9.25″ rear. Approx 0.630″ long.
Product Features:
See More
Product Features:
- Crush sleeve for Chrysler 8.0″ IFS and 9.25″ rear, also Ford 9″ with aftermarket Daytona pinion support
- 0.630″ tall
Driveworks – Oil Seal (Part No.S-722109)
from
$5.29
Value-priced seal meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
Yukon Gear – Replacement Oil Baffle For Dana 44 (Part No.33000)
Yukon Gear – Dana 25, 27, 30, 44, Model 20 And Model 35, GM 7.5", 8.2", 8.5", 12P, 12T, C9.25 Rear Cover Bolt (Part No.33286)
from
$9.99
5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.
Product Features:
See More
Product Features:
- Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
- 1/2″ head
Motive Gear – Drive Shaft Pinion Yoke (Part No.MG1310-6010)
Pro-King – Differential Internal Nest Kit (Part No.723A717)
from
$227.99
Pro-King is the leading supplier of transmission and driveline products in the aftermarket.
Product Features:
See More
Product Features:
- All products are designed to meet or exceed OE quality, form, fit and funtion.
Yukon Gear – 7290 U/Joint Strap Kit (4 Bolts And 2 Straps) For Chrysler 7.25", 8.25", 8.75", And 9.25" (Part No.41013)
from
$52.99
7290 U/joint strap kit (4 bolts and 2 straps) for Chrysler 7.25″, 8.25″, 8.75″, and 9.25″.
Product Features:
See More
Product Features:
- u-joint strap kit
- Fits Chrysler 7.25″, 8.25″ 8.75″ and 9.25″ rear
- 7290 u-joint size
- Includes two straps and four bolts
Yukon Gear – Six Piece Side Gear And Thrust Washer Kit For Chrysler 8" And 9.25" (Part No.33278)
from
$98.99
Six piece side gear thrust washer kit for Chrysler 8″ and 9.25″.
Product Features:
See More
Product Features:
- Side gear thrust washer kit
- Fits Chrysler 8″ and 9.25″
Yukon Gear – Zip Locker Bulkhead Quick-Disconnect Fitting (Part No.34038)
Dorman – Spindle Washer – I.D. 1-5/8 In. O.D. 2-3/16 In. Thickness 1/8 In. (sold by each) (Part No.618-040)
from
$4.79
This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
National – Bearings (Part No.M804049)
from
$38.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Yukon Gear – Standard Open Spider Gear Kit For 9.25" Chrysler With 31 Spline Axles (Part No.16004)
from
$333.99
Yukon standard open spider gear kit for 9.25″ Chrysler with 31 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Spider gear kit
- Fit Chrysler 9.25″ rear with open differential
- Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
Yukon Gear – C/Clip (Part No.33083)
from
$8.99
C/Clip for Chrysler 8.25″, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 8.2″, 8.5″ & 8.6″.
Product Features:
See More
Product Features:
- c-clip for Chrysler 8.25″, Ford 8.8″, GM 12 bolt car and truck and GM 8.2″, 8.5″ and 8.6″
- .150″ thick
Milemarker – MileMarker Street Master; Manual Hub (Part No.302)
from
$196.99
Black nylon reinforced fiberglass dial. Limited lifetime warranty. 19 spline, internal bolts. Chrome.
Product Features:
See More
Product Features:
- Black Nylon Reinforced Fiberglass Dial
- Limited Lifetime Warranty
Driveworks – Tapered Roller Bearing (Part No.S-M-804010)
Motive Gear – Differential Gear Install Kit (Part No.D44IK)
Timken – Axle Seal (Part No.K4021285194TIM)
from
$10.81
Axle Seal
Yukon Gear – The Carrier Bearing Puller (Part No.56072)
from
$883.99
The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.
Product Features:
See More
Product Features:
- Carrier bearing puller
- Works with an impact gun to safely and easliy remove carrrier bearings
Driveworks – Universal Joint (Part No.DW-534G)
from
$15.99
DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).
Product Features:
See More
Product Features:
- The cross is hot forged for the higher torque and horsepower
- The bearing cups are made by cold forging to provide higher strength and better rigidity
- Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
- Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
- Grease fitting allows for easy maintenance and the flexible use of the entire assembly
- Snap rings are held to strict tolerances to ensure proper cup position and retention
- Nitrile rubber seals are applied to optimize grease retention and reduce contamination
Yukon Gear – Yoke For Chrysler 8.25" With A 1310 U/Joint Size (Part No.41010)
from
$289.99
Yukon yoke for Chrysler 8.25″ with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses straps, with outside snap rings for the Jeep Cherokee. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Chrysler 8.25″
- 27 spline
- 1310 u-joint size
- Outside snap ring design
- 3.219″ snap ring span
- 1.062″ cap diameter
- Strap style
Yukon Gear – Steel Cover For Dana 44 Standard Rotation (Part No.32319)
Yukon Gear – Replacement Pinion Nut For Dana 25, 27, 30, 36, 44, 53 & GM 7.75" (Part No.33143)
from
$6.99
Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t
Product Features:
See More
Product Features:
- Pinion nut for Dana Spicer 25, 27, 30, 44, 50 and GM 7.75″
- 3/4″ x 16 thread
Yukon Gear – Standard Open Notched Cross Pin Shaft For 9.25" Chrysler (Part No.33309)
from
$84.99
Standard Open notched cross pin shaft for 9.25″ Chrysler.
Product Features:
See More
Product Features:
- Cross pin shaft
- Fits Chrysler 9.25″
- Standard open carrier only
- Notched
Yukon Gear – Redi-Sleeve Yoke Saver For 8.75" C, 9.25" C, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD (Part No.30228)
from
$37.99
Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.
Product Features:
See More
Product Features:
- Redi-Sleeve yoke saver
- Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD
Yukon Gear – Dana 44, 8.2", 12P, 12T, Vet, And Model 20 U-Bolts (Part No.41198)
from
$34.99
1310 U-bolts, 5/16″ x 1-3/8″ Dana 30, Dana 44, 8.2″, 12P, 12T, VET, Model 20.
Product Features:
See More
Product Features:
- u-joint u-bolt kit
- Fits AMC Model 20, Dana Spicer 30 and 44, GM 8.2″, 12 bolt passenger car and truck and 1963-1979 Corvette
- 1310 u-joint size
- Includes two u-bolts and four nuts
Yukon Gear – Powr Lok Button Kit For Dana 30, Dana 44 & Chrysler 8.75" (Part No.33536)
from
$67.99
Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t
Product Features:
See More
Product Features:
- Powr Lok button kit
- Fits Dana Spicer 30, 44 and Chrysler 8.75″
Popular 1976 Dodge W100 Drivetrains Categories
1976 Dodge W100 Drivetrains
You count on your 1976 Dodge W100 to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Drivetrains. With 397 Drivetrains ranging in price from $1.99 to $1,302.99, you’re sure to find everything you need for your 1976 Dodge W100.
Brands matter. If you want to shop a specific Drivetrains brand, we stock 16 different brands like Moog, Driveworks, and National. 1976 Dodge W100 Drivetrains start as low as $1.99!
One of the best ways to find top quality OEM or aftermarket Drivetrains is by asking professionals. Short of that, you can shop with confidence thanks to our 3,650 extensive product reviews on 1976 Dodge W100 Drivetrains. Some of the top-rated Drivetrains products we carry are Greaseable Super Strength Universal Joint with 4.4 stars and Greaseable Super Strength Universal Joint with 4.6 stars.
Did we mention you can order your Drivetrains from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Drivetrains inventory for your 1976 Dodge W100 below to get started!
Top-Rated Drivetrains Brands For Your 1976 Dodge W100
Trusted Drivetrains OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1976 Dodge W100 running right for years to come. In our inventory you’ll find brands like Moog, Driveworks, National, and even more.
Popular Spicer Drivetrains
You’ll find popular Spicer brand products across Universal Joints and Drive Shafts and Axles. All are waiting to get your 1976 Dodge W100 back on the road. Some of the top-rated Spicer products in these categories are:
Top-Rated MOOG Driveline Products Drivetrains
If MOOG Driveline Products are what you’re looking for, our inventory holds plenty. We stock MOOG Driveline Products brand Drivetrains for your 1976 Dodge W100, and some of our most reviewed MOOG Driveline Products parts include:
FAQs for 1976 Dodge W100 Drivetrains
What are the most purchased Drivetrains for the 1976 Dodge W100?
Out of 397 Drivetrains for the 1976 Dodge W100, the most popular in our inventory are:
What are the top-rated 1976 Dodge W100 Drivetrains?
Top-rated Drivetrains for your 1976 Dodge W100 based on customer reviews/ratings are:
from
$32.99
(37)
Greaseable Super Strength Universal Joint
“grease fitting I like location dont like needle design to grease should be regular design fitting”
