Name: Custom Fit 8.8mm; Spark Plug Wire Set
Brand: Accel
SKU: 8843
Price: 112.99 USD

from

$112.99

These ACCEL wire sets are custom tailored for true street and strip performance use. Features oversize 8.8 mm ultra performance wires and spark plug boots, 550 degrees Fahrenheit double silicone construction with fiberglass braid. Spiral wound steel core conductor.

Product Features:

8.8mm Graphite Suppression
Silicone Spark Plug Boots
550 Degree Double Silicone Construction
Fiberglass Braid
Carbon/Graphite Core
Magnetic Suppression
Fiberglass/Kevlar Core
500 Ohms Resistance

from

$44.99

Maximum electrical conductivity. Impact resistant. High dialectic strength. Prevents damage.

Product Features:

Maximum Electrical Conductivity
Impact Resistant
High Dielectric Strength
Prevents Damage

from

$35.99

Mr. Gasket has three types of exhaust gaskets–standard, Ultra Seal, and Copperseal. Use the standard for a stock rebuild and the Ultra or Copperseal for extra blowout protection.

Product Features:

Designed to provide excellent sealing and durability
Large fiber gasket material
Heat resistant
Reusable
Precision die cut for excellent fit
Limited warranty

from

$266.99

Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer

from

$359.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$25.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.

from

$13.99

The block-off plates are precision cut to cover stock fuel pump openings. Gasket included. Available in chrome plated or polished aluminum finish.

Product Features:

Chrome plated steel
Comes with gasket

from

$473.99

Edelbrock part #2711 Performer Oldsmobile 350 intake manifold is designed for 1964-85, 307-330-350-403 c.i.d. Oldsmobile V8 applications. For non-EGR, the #2711 manifold comes with a universal pad to fit most carburetors with electric chokes. Will fit 198

Product Features:

Idle-5500 RPM Range
Dual Plane Type-4150 Style Flange
3.74 in. Front Height, 4.27 in. Center Height, 4.8 in. Rear Height
Satin Finish
Non-EGR

from

$61.99

Made from heavy gauge steel, these chrome plated rear end covers are complete with bolts and gaskets.

Product Features:

Made of chrome plated steel
Fits GM 8 1/2 in. 10 bolt
Complete kit with gasket and bolts

from

$493.99

The Edelbrock 1403 Performer Series 500 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characterist

Product Features:

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Electric Choke
4 Barrel Count
Square Bore
Smooth Secondary Transition
Both Timed and Full Vacuum Ports
Includes PCV Outlet

from

$31.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

from

$71.99

If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.

Product Features:

Improved output coil for electronic ignitions
Works w/Blaster Ignition Or MSD 5/6/7 Series
Ballast Resistor Required If Used w/Stock Points Ignition
Alkyd tower w/high dielectric properties lessens carbon tracking

from

$266.99

Quality chrome plated and remanufactured to exceed OEM specifications for maximum dependability. Tested and output rated at 60 amps.

Product Features:

Exceeds OEM specifications
Output rated to 60 amps
Remanufactured

from

$23.99

Spectre’s Chevy short block timing cover kit is designed to protect engine components like timing gears and the timing chain. This kit features a triple chrome plated steel construction and includes a pre-installed seal, base gasket, (10) 12-point screws and a 12 point socket. This timing cover kit is engineered for optimum fit and function and it is designed to fit Chevy 265-400 short block engines.

Product Features:

Fits Small Black Chevrolet 265-400 Engines
Triple chrome plated
Steel construction
Includes pre-installed seal, gasket, (10) 12-point bolts and a 12 point socket
OEM fit & function
Spectre timing tab 4236 or 4237 is recommended

from

$113.99

Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

Easy Installation
Improved Fuel Economy
Reduced Maintenance
Accurate Timing
Improved Performance
Provides A Simple Conversion
No Moving Parts To Wear Out

from

$109.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$259.99

The B&M Unimatic is an ideal replacement for column shift vehicles, includes neutral safety switch, 5 foot cable and a boot and plate.

Product Features:

Ideal As Column Shift Replacement
Includes Neutral Safety Switch
Includes Black T-Handle
Backup Light Not Available
Includes 5 ft. Cable and Hardware
Includes Boot and Plate

from

$730.99

Product Features:

Best Way To Get A Major Power Increase
Power Increases From 50-70 HP
Work With Stock ECU
Simple Installation

from

$59.99

HEAVY DUTY-Firm positive shifts without loss of driver comfort for improved performance in all street vehicles. STREET/STRIP-Positive shifts for high performance street use or for competitive events. Hardest, quickest possible shift.

Product Features:

Provides Crisp Shifts
On Any Stock Automatic Transmission
Eliminates Soft/Sluggish Shift
Eliminates Shift Overlap
Eliminate Clutch and Band Wear

from

$40.99

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$25.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$88.99

Designed for 1968-1981 Buick 350 V8 engines, this valve cover features chrome-plated steel construction. The valve cover is stock height and baffled to provide optimum function. Spectre engineers its valve covers to look great for applications ranging from replacing a stock valve cover to a custom build. Includes two valve covers.

Product Features:

Fits 1968-81 Buick 350 V8 engines
Two valve covers are included
Steel construction with a triple chrome-plated finish
Features OEM style and height

from

$1243.99

Designed for carburetor V8 engines. Power increases from 200 to 400 horsepower. Simple to install. Shorter spray bars. More even distribution across the plenum. A more balanced air and fuel ratio. Quicker response time.

Product Features:

Designed For Carbureted V8 Engines
Power Increases From 200-400_ HP
Simple To Install
Shorter Spray Bars
More Even Distribution Across The Plenum
A More Balanced Air/Fuel ratio
Quicker Response Time

from

$5.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Saves Your Tie Rods
Lasts Longer
Looks Great

from

$54.99

K&N performance High-Flow Air Filters are engineered to improve engine performance. Unlike disposable paper filters which must be frequently replaced, K&N Air Filters are washable, reusable, and engineered to last for the life of your vehicle. K&N air filters are backed by our famous 10-Year/Million Mile Limited Warranty, and they provide an environmentally friendly way to reduce landfill waste by avoiding disposable filters. Engineered to fit easily into your factory air box, installation can be completed in a matter of minutes! K&N develops and tests each product on the world┐s toughest race tracks, so we can bring the highest level of performance to your daily driving. Join the millions of customers who have saved money and improved vehicle performance by upgrading to K&N filtration.

Product Features:

ENGINEERED POWER: State-of-the-art air filter media is designed to increase horsepower and acceleration as well as improve overall engine performance
RUGGED CONSTRUCTION: K&N Air Filters are manufactured with durable, premium materials and state-of-the-art construction methods to last a lifetime
4 LAYERS OF PROTECTION: Multiple layers of premium cotton gauze treated with a specially-designed tacking agent work together to create an intricate mesh of engine filter media that is designed to block and trap harmful contaminants
CLEAN ONCE EVERY 5 YEARS: Engine air filter only needs cleaning every 75,000 miles under normal highway driving conditions (based on the average miles driven per year of 15,000 miles)
ULTIMATE LONGEVITY: No-hassle lifetime warranty on stock replacement K&N air filters- limitations apply
EASY INSTALLATION: K&N Air Filters are pre-treated and ready to drop into your factory air box- they are one of the easiest and most cost-effective vehicle upgrades for quick performance gains
ECO-FRIENDLY: Using a washable, reusable engine air filter helps reduce replacement air filter waste- a K&N air filter is designed to last longer than 10 or more disposable filters
MADE IN USA: K&N Air Filters are proudly made in the USA for trusted quality & reliability

from

$36.99

Brake Bleeder Screws

from

$191.99

RngPnn

from

$29.99

Made of high durometer, very firm, Hyper-Flex performance polyurethane. They’re economical, increase efficiency and are easy to install. Use Energy Suspension sway bar end links with sway bar bushings to get the maximum performance benefit. Combine both for the same effect as buying a larger sway bar. Together they offer a dramatic improvement in performance and handling.

Product Features: