1975 GMC C15 Air Intakes
More 1975 GMC C15 Air Intakes Categories
If you’re looking for an original Air Intakes replacement for a 1975 GMC C15, you can search through our selection below. You’ll also find aftermarket and OEM Air Intakes to meet your needs.
Essential 1975 GMC C15 Air Intakes
Edelbrock – Carburetor Progressive Throttle Linkage Kit for Triple Carb Set-up (Part No.1033)
from
$186.99
The Edelbrock part #1033 Progressive Linkage Kit is designed to smooth throttle response, eliminate flat spots and improve fuel economy. It achieves this by only opening the center carburetor at less than 50% (or 33%) pedal travel thus sharpening the vent
Product Features:
See More
Product Features:
- Steel Material
- Zinc Plated
- Adjustable
- 3-Barrel Configuration
- Made In The USA
Edelbrock – Carburetor Gasket Kit #12371 Fits 4160 Carburetors (Part No.12371)
from
$19.99
The Edelbrock #12371 kit includes the primary fuel bowl gasket, the primary metering block gasket, the secondary metering block gasket and a metering plate gasket. The Edelbrock #12371 fits Holley 4160 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block Type
- Set of 4
- Fits Holley® 4160 Carburetors
- Made In The USA
Edelbrock – Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1221)
from
$43.99
Stamped from 18 gauge steel. Triple-chrome plated. High quality finish. Great looks. Works with all 5.152 inch carburetors. Base knock-outs for use with crankcase ventilation.
Product Features:
See More
Product Features:
- Stamped From 18-Gauge Steel
- Triple-Chrome Plated
- High-Quality Finish
- Great Looks
- Works With All 5.125 in. Carbs
- Base Knock-Outs For Use w/Crankcase Ventilation
Holley – Prem Street Carbs (Avengers) (Part No.0-80770)
from
$626.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Wells Vehicle Electronics – Carburetor Tune-Up Kit (Part No.2G1739)
from
$25.99
WVE is a leading source of advanced vehicle electronics components for replacement applications in the automotive aftermarket and original equipment applications. WVE offers high-technology manufacturing along with innovative solutions and improvements to OE designs. Every component either matches or improves on the OE design to ensure fast, easy installation, superior performance and reliability.
See More
Felpro – Air Cleaner Mounting Gasket (Part No.5292)
from
$3.29
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific, providing unsurpassed quality for a seal you can trust
- Validated for fit, form, and function
- Engineered for the sealing repair environment
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Felpro – Carburetor Choke Tube Gasket (Part No.72591)
from
$4.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Carquest – Needle and Seat (Part No.93-554R)
from
$9.49
High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.
Product Features:
See More
Product Features:
- Designed to OE standards for ease of installation
Dorman – Help – Throttle Return Spring (Part No.59209)
from
$9.99
This throttle return spring is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this throttle return spring matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this spring is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Edelbrock – Carburetor Vacuum Secondary Spring Kit #12412 Includes 7 Springs (Part No.12412)
from
$24.99
The Edelbrock #12412 Vacuum Secondary Spring Kit includes 7 springs that will fit on Holley 4150, 4150HP, 4160 series and various Demon Carburetors.
Product Features:
See More
Product Features:
- Steel Material
- For Holley® 4150, 4150HP, 4160; Demon King, Mighty, Race, Road, Sea, Speed; Barry Grant Claw
- Includes Lightest To Heavy
- Set of 7
- Made in The USA
Wells Vehicle Electronics – Carburetor Choke Pull-Off (Part No.1C1099)
from
$44.99
The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.
Product Features:
See More
Product Features:
- Application matched components ensure carburetor can be returned to like new condition.
Edelbrock – Carburetor Accelerator Pump Cam Kit #12403 for 2300, 4150, And 4160 Carburetors (Part No.12403)
from
$40.99
The Edelbrock #12403 Accelerator Pump Cam Kit Assortment Package of 8. These accelerator pump cams will have different shapes and profiles, allowing you to fine tune the accelerator pump’s performance to the engine’s requirements. Cam “lift” will directly
Product Features:
See More
Product Features:
- Multi-Color
- Plastic Material
- Fits Holley® 2300, 4150, And 4160 Carburetors
- Set of 8
- Made In The USA
Edelbrock – Standard Flow Carburetor Power Valve #12645 Single Stage 4.5in Hg (Part No.12645)
from
$16.99
Product Features:
See More
- The Edelbrock #12645 Single Stage 4.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
- During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.
Edelbrock – Standard Flow Carburetor Power Valve #12625 Single Stage 2.5in Hg (Part No.12625)
from
$16.99
The Edelbrock #12625 Single Stage 2.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate. During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation
Product Features:
See More
Product Features:
- Gasket Or Seal Included
- 2.5 in. Hg Opening Vacuum
- Single Stage
- Standard Flow Type
- Made In The USA
Spectre – Bolt Kit Intake Hex Head (Part No.4652)
from
$9.99
Spectre’s Intake Bolt and Washer Set is engineered to provide premium quality hardware for Chevrolet 265-400 and Chrysler 273-440 small block engines. Measuring 3/8 inch-16 by 1 inch, these grade 5 bolts feature a corrosion resistant zinc-plated finish and hex heads to ensure easy installation. This kit includes 12 bolts and washers.
Product Features:
See More
Product Features:
- Designed for Chevrolet 265-400 and Chrysler 273-440 small block engines
- 3/8 inch-16 by 1 inch bolts
- Kit includes 12 bolts and washers
- Manufactured from high quality steel
- Bolts feature hex heads
ARP Auto Racing – For Use With Chevy 265/ 400 Cubic", Hex Style Head Type, Polished, Ss (Part No.434-2001)
from
$46.49
Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.
Product Features:
See More
Product Features:
- Nominally Rated At 170,000 PSI Tensile Strength
- Precision Machined Threads For Secure Engagement, And Would not Rust
- Wide Under Head Flange And Companion Washers Provide Even Load Distribution
- Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
- Facilitates Optimum Sealing Of Gasket Surfaces
- 1″ Long
Edelbrock – Standard Main Jet Carburetor Metering Jet #12456 Size .055 (Pair) (Part No.12456)
from
$13.99
The Edelbrock 94 #12456 Carburetor Jets .056″ Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 56 Maximum Jet Size
- 0.055 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Standard Main Jet Carburetor Metering Jet #12457 Size .056 (Pair) (Part No.12457)
from
$13.99
The Edelbrock 94 #12457 Carburetor Jets .057″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 57 Maximum Jet Size
- 0.056 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Pro-Flo XT Small Block Chevy EFI Intake Manifold (Part No.7137)
from
$606.99
Edelbrock part #7137 Pro-Flo XT intake manifold is designed for 1957-86 S/B Chevy. This manifold is engineered with a large plenum and long tapered runners to deliver maximum horsepower and broad torque band throughout the rpm range (1500-7000 rpm). This
Product Features:
See More
Product Features:
- 1500-7000 RPM Range
- Single Plane Type-Throttle Body XT Style Flange
- 9 in. Front Height, 9 in. Center Height, 8.2 in. Rear Height
- Satin Finish
- Made In The USA
Edelbrock – Performer RPM Small Block Chevy Black Intake Manifold (Part No.71013)
from
$438.99
Edelbrock part #71013 Performer RPM intake manifold is designed for 1955-86 262-400 c.i.d. Chevy V8’s, for maximum power and a broad torque curve for high- Performance’street/marine engines. Provides power like a single-plane and throttle response like a
Product Features:
See More
Product Features:
- 1500-6500 RPM Range
- Dual Plane Type-4150 Style Flange
- 4.2 in. Front Height, 4.72 in. Center Height, 5.25 in. Rear Height
- Black Powder Coated Finish
- Non-EGR
Edelbrock – Triple Carburetor Fuel Log Kit #1288 with 5-1/2 in. Outlet Spacing (Part No.1288)
from
$99.99
This Edelbrock Fuel Log kit #1284 is an exact replica of the original design used by Vic Sr. in the 1950’s. They are made from extruded aluminum tube with a 3/8″ threaded outlet at each end and a polished finish. Kit includes, black neoprene hose, Corbin
Product Features:
See More
Product Features:
- Polished Log
- Brass Fittings
- Black Neoprene Hose
- 5-1/2 in. Outlet Spacing
- Includes Hose Clamps
Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)
from
$62.99
Product Features:
See More
- Customize Carburetor Calibration and Performance
- Owners Manual has Assembly Help
- Includes Metering Rod Retaining Spring
- Includes Metering Rods
- Includes Metering Jets
- Includes Step-Up Springs
Edelbrock – Intake Manifold replacement base to top gasket (Part No.6999)
from
$17.99
Replacement gasket for top to bottom. See PN(7110) complete. PN(7067) bottom. PN(7032) top. Includes base and top for intake manifold PN(7110).
Product Features:
See More
Product Features:
- Replacement Gasket for Top to Bottom
- See PN[7110]Complete; PN[7067]Bottom; PN[7032] Top
Felpro – INTAKE MANIFOLD GASKET SET (Part No.MS 90314-3)
from
$22.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
- ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
- REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
- EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
Mr. Gasket – Ultra Seal: Intake Gasket (Part No.5820)
from
$34.99
Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.
Product Features:
See More
Product Features:
- Manufactured from cellulose/nitrile composition gasket material
- Provides excellent sealing and durability
- Silicone beading on both sides of each gasket
- Complete with manifold end seals and distributor gasket
- For OE replacement, high performance street, drag race and oval track use
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$12.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Edelbrock – Carburetor Accelerator Pump Diaphragm #12401 50cc (Part No.12401)
from
$31.99
Edelbrock #12401 50cc Accelerator Pump Diaphragm for 4150 Carburetors. Proper installation is the responsibility of the installer. Improper installation will void your warranty and may result in poor performance and engine or vehicle damage.
Product Features:
See More
Product Features:
- Rubber Material
- For Holley®, Barry Grant, And Demon Gasoline Carburetors
- No Hardware Included
- 50cc Volume
- Made iIn The USA
Popular 1975 GMC C15 Air Intakes Categories
1975 GMC C15 Air Intakes
You count on your 1975 GMC C15 to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Air Intakes. With 109 Air Intakes ranging in price from $1.49 to $1,776.99, you’re sure to find everything you need for your 1975 GMC C15.
Brands matter. If you want to shop a specific Air Intakes brand, we stock 11 different brands like Felpro, Edelbrock, and Mr. Gasket. 1975 GMC C15 Air Intakes start as low as $1.49!
One of the best ways to find top quality OEM or aftermarket Air Intakes is by asking professionals. Short of that, you can shop with confidence thanks to our 386 extensive product reviews on 1975 GMC C15 Air Intakes. Some of the top-rated Air Intakes products we carry are Standard Flow Carburetor Power Valve #12625 Single Stage 2.5in Hg with 4.5 stars and Pro-Flo 1000 Series Chrome Air Cleaner with Foam Element with 5-1/8" Air Horn with 3.7 stars.
Did we mention you can order your Air Intakes from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Air Intakes inventory for your 1975 GMC C15 below to get started!
Top-Rated Air Intakes Brands For Your 1975 GMC C15
Trusted Air Intakes OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1975 GMC C15 running right for years to come. In our inventory you’ll find brands like Felpro, Edelbrock, Mr. Gasket, and even more.
Popular Felpro Air Intakes
You’ll find popular Felpro brand products across Air Cleaner Parts and Carburetor Parts. All are waiting to get your 1975 GMC C15 back on the road. Some of the top-rated Felpro products in these categories are:
Top-Rated Air Intakes
If are what you’re looking for, our inventory holds plenty. We stock brand Air Intakes for your 1975 GMC C15, and some of our most reviewed parts include:
FAQs for 1975 GMC C15 Air Intakes
What are the most purchased Air Intakes for the 1975 GMC C15?
Out of 109 Air Intakes for the 1975 GMC C15, the most popular in our inventory are:
from
$43.99
(19)
Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange)
Air Cleaner Assemblies
What are the top-rated 1975 GMC C15 Air Intakes?
Top-rated Air Intakes for your 1975 GMC C15 based on customer reviews/ratings are:
from
$16.99
(27)
Standard Flow Carburetor Power Valve #12625 Single Stage 2.5in Hg
“Works perfectly”
from
$31.99
(10)
Pro-Flo 1000 Series Chrome Air Cleaner with Foam Element with 5-1/8" Air Horn
“In store for pick up.”
from
$451.99
(7)
Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
“Easy install, had it installed in less then 30 mins on my 70 camaro 350 after my holley failed. It started right up only adjustment i had to do was tu”
