from

$24.99

A true performance application component for cars, trucks, hot rod, for racing and competition, yet popularly used for street vehicles when more horsepower is added. Soft running enough to absorb vibrations for street use yet rugged for racing use. Helps control torque on high performance vehicles. Maintains proper drive shaft angle to help prevent early wear and unexpected power train damage. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal transmission mounts. Resistant to under vehicle fluid oils, coolants and road contaminants. Made of Energy’s Hyper-Flex performance polyurethane and heavy duty hardware – for added durability.

Product Features:

Made from HYPER-Flex Polyurethane
Firm Enough for Huge Amounts of Horsepower/Torque
Soft Enough Not to Transmit Vibration

from

$840.99

The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, New turbine hub and dual pattern drive lugs on some Holeshots.

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$47.99

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$397.99

Burnished aluminum. GM/MAC- style throttle linkage. Electric choke installed from factory. Easy tuning with 2 piece design. Smooth secondary transition. Both timed for full vacuum ports. Includes PCV outlet.

from

$35.99

Manufactured from high-density cork and rubber blend gasket material. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals where applicable. For OE replacement and high performance street.

Product Features:

One-piece design
Eliminates potential leaks
Prevents over tightening
Prevents torque loss

from

$703.99

Hi-Ram Intake Manifold

from

$91.99

Fits 1970 and up Chrysler, Dodge, Plymouth with a 440 CID engine using a Torqueflite A727 automatic transmission. Works with an externally balanced high performance forged crank. Has dual bolt pattern, 10 in. and 11-1/8 in. SFI spec 29.1 approved, NHRA and IHRA legal for all classes. SFI certification sticker included (re-certification required every 3 years). Ideal for street applications to extreme duty racing and high RPM (above 6,000) use. B&M’s new Radial Tension Technology puts a new spin on flexplate technology. As engine performance levels increase, stronger flexplates become necessary. Until this point, stronger flexplates meant thicker flexplates. This works, but it adds unwanted weight and prohibited the flexplates from working as it was designed. Flexplates are designed to provide a protection against converter and transmission run out or OEM misalignment, which will cause transmission and/or converter failure. A rigid flexplate gives no protection. The ultimate design for a flexplate is extreme strength, flexibility and minimal weight. B&M’s new RTT performance flexplate accomplishes this goal. B&M’s design allows for the removal of unnecessary material from non-critical stress areas. Less material means less weight giving you the benefits of a lightweight, flexible design with thicker material for maximum strength!

Product Features:

NHRA and IHRA Legal For All Classes
Includes SFI Certification Sticker
Ideal For Street Applications
To Extreme Duty Racing
To High RPM Use

from

$645.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$72.99

Product Features:

Cylinder Head Gasket
1958-1979 361-383-400-413-426
Not For Hemi

from

$2198.99

The Edelbrock #5093 E-Street cylinder heads are designed for use with 1961-1979 Chrysler 361-440 c.i.d. Wedge engine applications. The Edelbrock E-Street cylinder heads offer American made quality and affordable performance. E-Street cylinder heads featur

Product Features:

Complete Pair For Hydraulic Flat Tappet
84cc Combustion Chamber Volume
210cc Intake/70cc Exhaust Runner Volume
2.14 in. Intake/1.81 in. Exhaust Valve Diameter
0.625 in. Deck Thickness

from

$71.99

If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.

Product Features:

Improved output coil for electronic ignitions
Works w/Blaster Ignition Or MSD 5/6/7 Series
Ballast Resistor Required If Used w/Stock Points Ignition
Alkyd tower w/high dielectric properties lessens carbon tracking

from

$461.99

The B&M Megashifter has it all, form, function and classic style. This all adds up to bring you a quality shifter that’s been one of the most popular automatic shifters of all time. First off let’s talk function. The Megashifters positive ratcheting funct

Product Features:

Universal Floor Mount
Base Can Be Trimmed-Custom Fit
Cable Operated
Quick Installation
Accurate Shifting

from

$165.99

This Spectre Oil Pan was designed for the big block Chrysler/Dodge/Plymouth 383, 400, 413, 426, & 440 engines. This triple chrome plated oil pan is made to replace the oem oil pan.

Product Features:

Triple chrome-plated
Steel construction
Stock capacity
Made from high quality material

from

$26.99

These high performance thermostats are designed to resist large variations in coolant pressures that occur at high RPM’s where coolant temperature and coolant pressure fight for control of the thermostat keeping it from opening at its designated temperature. The balanced HP thermostat features all brass and copper construction, and opens at the right temperature regardless of engine RPM.

Product Features:

High performance
Resists variations in coolant
Brass and copper construction
Opens at right temperature

from

$389.99

Product Features:

Remote Thermostat Housing

from

$16.99

FRAM Racing® filters are designed with a heavy-gauge tapping plate and an extra-thick* steel can that is able to withstand the high pressure flexing caused by demanding driving conditions. A spiral-shaped center tube provides protection against collapse, and tough steel end caps add even more durability. A screen-over 22psi filter bypass valve provides additional protection against larger contaminants.**

Product Features:

Proven protection for up to 10,000 miles
Engineered for use with synthetic or conventional motor oils
Filter media is a blend of fiber and resin that captures 95% of the dirt particles
The perfect balance of dirt-trapping efficiency and dirt-holding capacity

from

$54.99

Knowing your coolant temperature can help to prevent burn injuries. Thermo Cap, with its built-in calibrated thermometer, indicates the coolant temperature. This is useful information prior to cap removal. Never attempt to remove Thermo Cap when the coolant temperature is very hot. The escaping hot coolant and steam may burn you. Check the Thermo Cap temperature indicator to determine if the coolant is cool enough to make removing Thermo Cap safe. If the coolant is very hot, then thoroughly rinse the radiator with cool water, until the coolant temperature drops into a cooler safe zone Thermo Cap’s integrated coolant reclamation valve works great with your coolant recovery system. Your radiator can reclaim coolant from your overflow bottle. Wide 30 degree to 270 degree Fahrenheit temperature range. Calibrated in centigrade and Fahrenheit. Color-coded temperature ranges. Chromed crown with a colored trim ring. Indicates coolant temperature, Helps to prevent coolant injuries, integrated coolant reclamation valve, Improves under hood appearance, Fits most domestic or import vehicles and various valve pressures available.

Product Features:

Indicates coolant temperature
Helps to prevent coolant injuries
Integrated coolant reclamation valve
Improves under hood appearance
Fits most domestic vehicles
Built in calibrated thermometer

from

$25.99

Product Features:

Service Part
Makes Connections Quick And Easy

from

$76.99

The Edelbrock #4495 Signature Series Valve Covers are designed for Chrysler 318-340-360 V8 ’65-91 applications. Engineered for function and styled for great looks, Signature Series valve covers have stock-style breather baffles that prevent oil passage to the PCV valve. These quality valve covers accept all emissions equipment, including PCV valve holes. Rubber grommets for the breather and PCV valve holes are included. Matching breathers sold separately.

Product Features:

Small Block Chrysler 318-360,65-91
Short
Chrome Steel
Set Of Two
Rubber Grommets For Breather

from

$398.99

RngPnn

from

$20.29

Fel-Pro® Performance Gaskets deliver reliable sealing under grueling racing conditions.

Product Features:

Blue Stripe® performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.

from

$1243.99

Designed for carburetor V8 engines. Power increases from 200 to 400 horsepower. Simple to install. Shorter spray bars. More even distribution across the plenum. A more balanced air and fuel ratio. Quicker response time.

Product Features:

Designed For Carbureted V8 Engines
Power Increases From 200-400_ HP
Simple To Install
Shorter Spray Bars
More Even Distribution Across The Plenum
A More Balanced Air/Fuel ratio
Quicker Response Time

from

$206.99

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:

High Output Fuel Flow
Flows 110 gph Free Flow
Shutoff Pressure Pre-Set From 6.5 To 8 PSI
Fuel Pressure Regulator Is Not Required
Heavy Duty Construction For Continuous High rpm Operation
Fuel Body Casting Can Be Rotated For Plumbing Situations
Inlet And Outlet Tapped For 1/4 in. NPT
Inlet/Outlet Tapped For 3/8 in. NPT

from

$48.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$52.99

These ACCEL wire sets are a true performance upgrade replacement for OE types. Efficient delivery of spark energy for a good price. Silicone boots with blue, black, red and yellow wire, zinc-plated steel terminals. Tinned copper core.

Product Features:

Graphite Suppression Eliminates RFI/EMI
3000 To 7000 Ohms Per Foot Of Resistance
Silicone Spark Plug Boots
450 Degree Temperature Rating
Meets Or Exceeds OE Boot Temperature Rating

from

$149.99

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1962-up TF727 transmissions and all internally balanced Chrysler, Dodge and Plymouth V8 engines with 6-bolt crankshaft flange. Features include high tensile strength steel construction to resist elongation and cracking, dual bolt pattern 10.00 or 11.125 inch converter mounting locations and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953.

Product Features:

NHRA/IHRA Legal For All Classes
Includes SFI Certification Sticker
Ideal For Street Applications
To Extreme Duty Racing
To High RPM Use

from

$52.99

Spectre’s Differential Covers are made to OEM specifications and are triple chrome plated for a lasting shine. Designed to protect the intricate moving parts of the differential, Spectre’s covers add an extra layer of protection to the vehicle’s underside. Featuring a 10-bolt design and fits 1961-1989 Chrysler cars with a 8-1/4 inch ring gear. Includes 10 SAE standard chrome bolts for installation. You’ll need to supply your own bolts if your application requires metric bolts.

Product Features:

10 bolt design cover
Bolts and gasket included
Triple chrome plated for a lasting shine
10 chrome 5/16 inch -18 x 3/4 inch differential cover bolts included

from

$27.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted