1975 Chevrolet Malibu Performance Engines

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered and manufactured specifically for repair applications
• Unsurpassed quality you can trust
• Validated for fit, form, and function

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Rigid core, molded silicone rubber gaskets utilize the one-piece molded rubber technology for a perfect fit, ease of installation and include compression limiters to prevent overtightening.
• Not intended for use in emission controlled vehicles.

Product Features:

• Designed for Optimum Torque and Acceleration
• Maximum Performance From Idle through Mid-Range
• Matched to Edelbrock Performer Intakes
• Includes Hydraulic Lifters and Assembly Lube
• Major Improvement in Throttle Response and Torque
• Use For Daily Drivers/Trucks/Vans/RVs/4x4s
• Take The Guesswork Out Of Camshaft Selection

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Excellent resilience. High temperature endurance. Will not creep or cold-flow. Will not get brittle. Resists corrosion. Eliminates gasket sealer. Compatible with high octane and exotic fuel.

Product Features:

• Excellent resilience
• High temperature endurance
• Will not creep/cold-flow
• Will not get brittle
• Resists corrosion
• Eliminates gasket sealer
• Compatible w/high octane fuel
• Compatible with exotic fuel

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

Edelbrock camshafts are matched to Edelbrock Total Power Package components for proven performance, taking the guesswork out of camshaft selection. They are compatible with OEM or Edelbrock hydraulic roller tappets which reduce friction, virtually eliminate break-in problems, and permit higher valve velocities for increased performance. Designed to work with Torker II manifolds for performance from 2500 to 6500 RPM, these camshafts are ideal for high-performance street, drag or marine applications. Torker-Plus cams have a slightly rough idle and are not suitable for trucks or towing applications. Hydraulic flat tappet lifters are included with each camshaft.

Product Features:

• Designed for 2500 to 6500 Performance
• Designed for Hi-Perf Street; Drag or Marine Use
• Matched to Edelbrock Torker II Intakes
• Includes Hydraulic Lifters and Assembly Lube
• Dyno Matched/Street Proven Performance
• Take The Guesswork Out Of Camshaft Selection

Manufactured from a blend of nitrile rubber and fiber for excellent sealing and durability. Precision die cut for application.

Product Features:

• Edge molded rubber water outlet gasket is reusable
• Requires no gasket sealer
• Solid aluminum carrier for strength/rigidity

TIMING COVER SEAL

Edelbrock #88503 Water Pump big block Chevy short black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cooling” Water Pu

Product Features:

• Standard Impeller Rotation
• 0.625 in. Pilot Shaft
• 0.750 in. Ball/Ball Bearing
• 5.750 in. Block To Hub Height
• Black Finish

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Die cut silicone rubber gaskets conform to out-of-flat covers
• Great for on-again/off-again situations
• Not intended for use in emission controlled vehicles.

Features two threaded bosses for temp control switch satin finish.

Product Features:

• Emission System Water Outlet

Avoid trouble with this precision timing tape. Use it for accurate timing, setting valve lash or when degreeing the harmonic balancer.

Product Features:

• Accurate in calibration
• For hi-performance engines
• Increased performance
• Set valve lash at proper time

Product Features:

• 50-State Street Legal Aluminum Cylinder Head
• Out-of-the-Box Bolt-On Performance
• 70cc Combustion Chambers Improve Performance
• Retain Stock Compression Ratio

Spectre’s Engine Dress-Up Kit was designed for the ’58-’86 Chevrolet small block 265-400. This kit includes: stock height baffled covers, chrome T-bar hold downs, chrome PCV breather, chrome breather, chrome oil filler cap, grommets, and a stainless steel braided PCV hose with red/blue Magna-Clamps. Designed for use with OE specifications for fit and function, Spectre products are engineered to perform as good as they look.

Product Features:

• For Chevrolet small block 265 and 400
• Kit includes: stock height baffled covers, chrome T-bar hold downs, chrome PCV breather, chrome breather, chrome oil filler cap, grommets, and a stain
• Designed for use with OE specifications for fit and function
• Made from high quality material

The K&N PreCharger® filter wrap is specially designed to extend the service interval of your K&N Filtercharger filter when used in very dusty conditions. They are made from durable polyester material containing a uniform weave. The PreCharger will stop small dirt particles with minimal restriction to the airflow of the filter.

Product Features:

• Cellulose nitrile composition
• Silicone beading on both sides
• Create a leak proof seal
• Double beaded, includes EGR restrictor plate

The throttle cable bracket is designed for small block Chevy engines thru 1979 and is to be used in conjunction with the kick down cable Pn9886 for the Turbo 350 transmission. The throttle cable bracket mounts on the intake manifold and will hold cables with round or square mounts. It has a 2 inch adjustable range and is finished off in a beautiful chrome plating.

Product Features:

• 2 in. adjustable range
• Includes necessary hardware
• Chrome plated
• Individually packaged

Product Features:

• Case-Hardened Tubing
• Surface Hardening
• Welded Ends
• 0.3125 in. Diameter
• Use with or without Hardened Steel Guideplates

Magnum Pushrods from COMP Cams offer an affordable solution for your .080″ wall chromemoly pushrod needs. Designed to withstand the stresses of a high performance engine, Magnum Pushrods are head-treated for extended durability and have precision formed, reinforced ends. Magnum Pushrods are black-oxide finished with their part number and length laser etched onto the surface for easy identification.

Product Features:

• 3/8″ Diameter, 7.800″ Length
• Magnum Pushrods for Small Block Chevy
• One-piece .080″ wall chromemoly steel tubing
• Heat-treated for extended durability and guide plate compatibility
• Precision formed and reinforced pushrod end

Grade 8, single bolt. Black plated finish. The washers are designed to secure the Mr. Gasket cam button pn1180, pn1181, and pn1183 or can be used as stock replacements.

Product Features:

• Specialty and drive train fastener
• Special cam bolts
• Black plated finish

For 4500 to 8500 RPM drag race applications. Has deeper and larger plenum than Victor Jr. For standard port location iron and aluminum heads. Extra material allows port matching. Great choice for NHRA super stock classes. Also great for alcohol-fueled applications. Can use 1 or 2 inch spacers to tune performance. EFI fuel injector bosses featured on PN(29785).

Product Features:

• For 4500 to 8500 RPM Drag Race Applications
• Has deeper and larger plenum than Victor Jr.
• For standard port location iron and aluminum heads
• Extra material allows port matching
• Great choice for NHRA Super Stock Classes
• Also great for alcohol-fueled applications
• Can Use 1 Or 2 in. Spacers To Tune Performance
• EFI Fuel Injector Bosses featured on PN[29785]

Product Features:

• Hi-Ram; Intake Manifold Runner Section

This stud uses heat treated grade 8 alloy steel. The enlarged radius base provides extra strength for a more durable stable shank. Black plated finish. Fits Chevy small block and Ford small block.

Product Features:

• Heat-treated
• Grade 8 alloy steel
• Ex strength enlarged radius
• More durable/stable shank
• Prevents stud flexing
• Black plated finish

Designed to keep the rocker arms positively locked for precise and critical valve train adjustments. Manufactured from quality grade steel, then heat-treated for extra strength and plated with a durable finish. Kits include 16 rocker arm nuts with socket head set screws and one hex key wrench.

Product Features:

• Sure-lock rocker arm nuts
• Precise valve train adjustment
• Keep rocker arms locked
• High-quality grade steel
• Heat-treated for ex strength
• Plated with durable gold tone finish

Designed to keep the rocker arms positively locked for precise and critical valve train adjustments. Manufactured from quality grade steel, then heat-treated for extra strength and plated with a durable finish. Kits include 16 rocker arm nuts with socket head set screws and one hex key wrench.

Product Features:

• They are zinc dichromate plated steel
• They have black oxide coated set screws
• Keeps rocker arms positively locked

Product Features:

• Timing Chain Only

Product Features:

• Solid Bushing Chain Resists Stretching
• For Use with Stock or Edelbrock Camshafts
• Stressproof Steel Crank Gears
• 3 Keyway Setting Points To Ensure Accurate Timing
• True Bearing Surface Rolls with the Sprockets