1974 Plymouth Duster Differentials

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Oil baffle for Dana Spicer 60 and Dana Spicer 70U

Yukon Gear & Axle offers a full line of top quality differential tools to save time and money.

Product Features:

• Fits HM88510 race
• All-steel construction
• For accurate installation of bearing races

Replacement ring gear bolt for Dana 60, 70, 70U & 70HD, 1/2″ x 18.

Product Features:

• Ring gear bolt for Dana Spicer 60, 70, 70U and 70HD
• 1/2″ x 18 thread

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

8.25″ Chrysler cover gasket.

Product Features:

• Cover gasket
• Fits Chrysler 8.25″

Yukon Minimum Installation Kits are a low-cost solution for ring and pinion gear changes in newer vehicles where the bearings can be reused. Kits include all high-quality components for a smooth differential set up.

Product Features:

• Fits 1975 and down Chrysler 8.25″
• Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin bolt for AMC Model 35 with c-clip axles

Yukon Mighty Seals use the latest design and manufacturing technologies to produce a precision fit that seals tight and lasts for years to come.

Product Features:

• Pinion seal
• Fits Chrysler 8.75″ with ’41’ and ’89’ case housings and 2000 and down Chrysler 9.25″

Yukon Gear & Axle manufactures a full line of top-quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers, and other general maintenance items. You can count on Yukon to fulfill all your differential small parts needs.

Product Features:

• Clutch kit
• Fits Dana Spicer 44 and Chrysler 8.75″ Power Lok
• Aggressive design

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin bolt for Dana Spicer 60 with c-clip axles

Product Features:

• CHRYSLER 7.25″ INTERNAL KIT

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Pinion gear thrust washer for Dana Spicer 60
• Fits standard open and Trac Loc applications

RngPnn

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

• Fits Chrysler 8.25″ with 27 spline axles
• Made from 9310 steel for added strength
• Replaces the spiders in a standard carrier case

Product Features:

• Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.
• Dana engineering-approved for fit, form and function
• Meets or exceeds OE specifications

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin shaft
• Fits Chryler 8.25″
• 0.801″ diameter
• Notched
• Not compatible with Spartan Lockers or Lock Rights

Yukon Pinion Installation Kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings and races can be reused. This kit features Timken bearings and races along with high-quality seals and small parts. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your gear set.

Product Features:

• Fits 1975 and down Chrysler 8.25″
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

Yukon right hand axle for ’10-’14 Ford F150 SVT Raptor front, 31 spline.

Product Features:

• Bulkhead quit connect fitting

Yukon Mighty Seals use the latest design and manufacturing technologies to produce a precision fit that seals tight and lasts for years to come.

Product Features:

• Redi-Sleeve yoke saver
• Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

Yukon spider gear set for GM 8.2″ Dura Grip posi, 28 spline. This kit does not include clutches. This kit fits Yukon Dura Grip ONLY.

Product Features:

• Cover gasket
• Fits Dana Spicer 60, 70, 70U and 70HD

Yukon 4340 Chrome-Moly replacement inner axle for Dana 60 with a length of 16.17″ and 35 splines. Yukon 4340 Chrome-Moly axles provide up to 50% increased strength over stock axles for use in extreme performance applications with large tires and high horsepower. Yukon’s 4340 axles are manufactured using the latest technologies and the highest quality materials to ensure high strength and long life. Limited Lifetime warranty covers manufacturing defects and axle breakage for as long as you own the vehicle. This warranty is not transferable to another party. “No Questions Asked” replacement for first warranty return, however Yukon reserves the right to either replace axle or refund original purchase price after the first warranty claim. Yukon (through Randy’s ring & pinion) makes final determination on warranty considerations.

Product Features:

• Rubber fill plug
• Fits Chrysler 7.25″, 8.25″ and 9.25″

Yukon Carrier Installation Kits are a convenient and low-cost solution for carrier changes in cases where one is upgrading to a positraction limited slip differential, a mechanical locker, or an air operated locker. These kits contain carrier bearings and races and a carrier shim kit.

Product Features:

• Fits 1976 and up Chrysler 8.25″
• Includes carrier bearings and races

Yukon shim kits are precision machined and tailored for each individual application to ensure you have the right shims for every set up.

Product Features:

• Pinion depth shim kit for Toyota 7.5″, 8″ and V6

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
• For Trac Loc positraction applications only

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Pinion nut for Chrysler 8.0″ IFS, 8.25″, 8.75″ with 29 spline pinion and 9.25″ rear
• 7/8″ x 14 thread

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

• Cover bolt for Dana Spicer 60, 70 and 80
• 3/8″

Product Features:

• MINI INSTALL KIT CHRYSLER 8.25 8 1/4″