from

$417.99

Yukon Performance 1-3/4″ deck steel spool for 8.5″ GM with 30 spline axles. Uses large bearings, 1.785 journals. Yukon performance spools are made from the highest quality materials to ensure high strength and long life in performance applications. Spools provide 100% power to both tires at all times and are a lower cost alternative to lockers. Spools are not recommended for street driven vehicles. Yukon Performance spools come with a one year warranty against manufacturing defects. This spool requires the use of a C-Clip eliminator kit to be used.

Product Features:

Fits GM 8.5″ with 30 spline axles
2.73 and up ratios only
Provides 100% traction to both wheels at all times
Not recommended for street driven vehicles

from

$41.99

Product Features:

Shim kit
Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction

from

$8.99

Positraction clutch guide.

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44, Dana Spicer 50, Ford 8.8″, GM 12 bolt passenger car, GM 8.2″, 8.5″ and 8.6″, 1963-1979 Corvette and Nissan Titan
Compatible with Dura Grip positractions only

from

$57.99

8.5, 9.5, & 8.2 Buick, Oldsmobile, Pontiac GM REDI sleeve yoke saver.Yukon Mighty seal.

Product Features:

Pinion Redi-sleeve
Fits GM 8.5″, 9.5″ and 8.2″ Buick, Oldsmobile and Pontiac

from

$214.99

Product Features:

Spider gear kit
Fits GM 8.5″ 30 spline open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$8.99

7.5 & 7.625 Standard Open Pinion gear Thrust Washer.

Product Features:

Pinion gear thrust washer for GM 7.5″ and 7.625″
Fits standard open differentials only

from

$11.99

GM 7.5″ standard Open side gear thrust washer.

Product Features:

Side gear thrust washer
Fits GM 7.5″

from

$137.99

Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil

from

$187.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 1981 and down GM 7.5″
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$148.99

Product Features:

SUPER KIT-GM 7.5 (1977-81)*TIMKIN*

from

$61.99

Made from heavy gauge steel, these chrome plated rear end covers are complete with bolts and gaskets.

Product Features:

Heavy gauge steel
Chrome plated

from

$98.99

Motive Gear Mini-Spools replace your stock spider and side gears with a solid billet mini-spool for 100% traction to both wheels. Not recommended for street applications.

Product Features:

Billet construction
Not recommended for street applications
GM7.5″ MINI SPOOL 26 SPLINE

from

$6.99

Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

Product Features:

Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS

from

$14.99

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.5″, 8.6″ & 9.5″.

Product Features:

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.625″, 7.6″ IFS, 8.5″, 8.6″ and 9.5″.

from

$14.29

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$1.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$279.99

Yukon spider gear set for GM 7.5″ & 7.625″ Dura Grip posi, 26 spline. This kit does not include clutches. This kit fits Yukon Dura Grip ONLY.

Product Features:

Spider gear kit
Fits GM gm 7.5″ with 26 spline Dura Grip positraction
Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$223.99

Product Features:

GM 10BL 7.5 &7.625 R/P 3.73 MGP 10 3/8 X 18 LH THRED BLTS, PD=1.438

from

$42.99

Product Features:

Shim kit
Fits GM 7.5″ and 7.625″ with Eaton positraction

from

$49.99

Product Features:

MINI INSTALL KIT GM 7.5

from

$108.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

Fits GM 7.5″ and 7.625″
Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

from

$8.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o

from

$15.99

Precision cut and high quality materials. Reusable.

Product Features:

Precision cut
High-quality materials
Reusable

from

$188.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M802011 race
All steel construction

from

$119.99

The Motive Gear replacement axle shaft offers an OE-quality axle shaft at a fraction of the OE cost. Manufactured from 1541H material on high-tolerance CNC equipment, this axle shaft is designed to provide a perfect fit every time.

Product Features:

AXLE SHAFT 8.2″ 28 SPL. 29 5/8″ L&R DOUBLE DRILLED

from

$57.99

Cross pin shaft for 7.5″, 7.625″, and 8″ GM.

Product Features:

Cross pin shaft for GM 7.5″, 7.625″ and 8.0″
Fits standard open differentials only

from

$6.49

This differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles
Required replacement – when servicing the differential
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience