1974 Dodge Challenger Differentials

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

• Redi-Sleeve yoke saver
• Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

Dana 44 & 9.25 Chrysler TracLoc clutch kit.

Product Features:

• Clutch kit
• Fits Dana Spicer 44 and Chrysler 9.25″ Trac Loc positraction

Yukon yoke for Chrysler 7.25″ and 8.25″ with a 7290 U/joint size. 2.625″ snap ring span. 1.125″ cap diameter. Inside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Chrysler 7.25″ and 8.25″
• 27 spline
• 7290 u-joint size
• Inside snap ring design
• 2.625″ snap ring span
• 1.125″ cap diameter
• Strap style

Positraction clutch guide.

Product Features:

• Clutch guide for Chrysler 9.25″, Dana Spicer 44, Dana Spicer 50, Ford 8.8″, GM 12 bolt passenger car, GM 8.2″, 8.5″ and 8.6″, 1963-1979 Corvette and Nissan Titan
• Compatible with Dura Grip positractions only

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits 2000 and down Chrysler 9.25″ rear
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

Product Features:

• Fits Chrysler 9.25″ rear with open differential
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

• Fits Chrysler 8.75″ ’89’ case housing with 25520 carrier races
• Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve , thread locker, marking compound with brush, and gasket.

89 housing nodular Iron Drop Out case, up to 500 HP, Billet adjuster for 8.75″ Chrysler. This dropout does not come with fill plug (Part number CHY612017).

Product Features:

• Fits Chrysler 8.75″
• ’89’ case design
• Nodular iron for added strength

Product Features:

• Pinion depth shims for Dana Spicer 60 and 70U

Product Features:

• Dura Grip positraction carrier case
• Does not include spider gears
• Fits Chrysler 9.25″ rear

Differential side bearing screw adjuster for 9.25″ Chrysler.

Product Features:

• Side adjuster for Chrysler 9.25″ rear

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits HM89410 race
• All steel construction

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Chrysler 9.25″ rear
• Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

Six piece side gear thrust washer kit for Chrysler 8″ and 9.25″.

Product Features:

• Side gear thrust washer kit
• Fits Chrysler 8″ and 9.25″

Cross pin shaft for standard open Chrysler 9.25″, .860″ diameter. Will not fit posi!

Product Features:

• Cross pin shaft for Chrysler 9.25″
• Fits standard open differentials only
• 0.860″ diameter

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Chrysler 9.25″ rear differential. This kit contains carrier bearings and races.

Product Features:

• Fits Chrysler 9.25″ rear
• Includes carrier bearings and races

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

Product Features:

• Rubber fill plug
• Fits Chrysler 7.25″, 8.25″ and 9.25″

Product Features:

• CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
• PREMIUM MATERIALS: Precision manufactured using high-quality materials for durability and performance
• OE-STYLE DESIGN: Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Bolt/screw for adjuster lock for Chrysler 7.25″, 8.25″, 8.75″, 9.25″.

Product Features:

• Side adjuster lock bolt
• Fits Chrysler 7.25″, 8.25″, 8.75″ and 9.25″

A worn or damaged differential pinion flange can lead to driveline vibrations and fluid leaks. This part is designed to match the performance of the original equipment pinion flange on specified vehicles. It has been engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is rusted, worn or damaged. It is made of rugged materials for reliable service and durability.

Product Features:

• Direct replacement – this differential pinion flange is designed to match the performance of the original equipment flange on specified vehicles
• Ideal solution – engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is worn or damaged
• Durable construction – designed and manufactured to strict specifications for reliable performance
• Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

Crush Sleeve for Model 35, Chrysler 7.25″, 8.25″ Ford 8″ & GM 7.75″. Approx 0.495″ long.

Product Features:

• Crush sleeve for AMC Model 35, Chrysler 7.25″ and 8.25″, Ford 8″ and GM 7.75″
• 0.495″ tall

Product Features:

• Fits Chrysler 9.25″ rear
• Steel

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

Product Features:

• BILLET HP 1350-29 SPLINE YOKE

RngPnnInstlKt