from

$498.99

The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, New turbine hub and dual pattern drive lugs on some Holeshots.

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$21.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$37.99

Spectre’s High Performance Replacement Air Filters are engineered to outperform ordinary paper filters by providing increased air flow for improved performance. Manufactured using high quality materials including pre-dyed synthetic media, urethane, and steel mesh, this performance air filter is factory pre-oiled and ready to use.

Product Features:

High performance and high air flow filter
Filter media is non-woven synthetic and pre-dyed
Replaces stock air filter
Easy to install with no special tools or skills required
Reinforced with a steel mesh

from

$49.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

from

$549.99

High burst strength woven lining to withstand heat and higher engine RPM. Heavy-duty sprung hub assembly to allow smooth engagement and steady torque transfer without chatter. Recommended for high horsepower street vehicles in addition to occasional drag strip use.

Product Features:

Built As Matched Assembly
Exceptional Performance
Exceptional Durability
Long Term Dependability

from

$18.99

Oil Pan Bolt Kit

from

$25.99

Product Features:

Service Part
Makes Connections Quick And Easy

from

$96.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets

from

$149.99

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1971-92 Chrysler, Dodge and Plymouth 360ci (externally balanced) V8 engines with A904 transmission. Features include high tensile strength steel construction to resist elongation and cracking, 10.00 inch bolt pattern and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953.

Product Features:

NHRA/IHRA Legal For All Classes
Includes SFI Certification Sticker
Ideal For Street Applications
To Extreme Duty Racing
To High RPM Use

from

$125.99

Kits include most popular chrome dress-up components, including short, OEM height valve covers with integral oil baffles.

Product Features:

Includes oil baffles
Chrome plated

from

$426.99

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in

Product Features:

Maximum Cooling for Street and Racing Engines
Internal Passages Are Balanced for Maximum Flow
Impeller is Larger than Others For Max Pressure
Impeller Vanes Dramatically Increase Flow Rates
Equal Distribution to Both Sides of Block
Only Flows in One-Direction for Optimum Efficiency

from

$379.99

Our advanced power system line has grown to include starters. Our new APS starter is designed to crank over the highest compression engines on a hot day in Death Valley. Not that too many race cars are sitting in Death Valley, but it’s good to know that you have the oomph to make it happen. The APS starter features all new components beginning with a three horsepower motor. This power is used to crank over the reduced 4.4:1 gear set to deliver great torque to the engine’s ring gear to get the engine turning. The armature is balanced during assembly and is guided by two ball bearings for smooth engagement and thousands of starts. The downsized housing clears most headers and oil pans, but just in case, we made the billet mount so it can be clocked in different positions to help in tight applications. The assembly is powder coated MSD red and will stay looking good, even though it’s underneath your car.

Product Features:

Mount Can Be Clocked To Assist In Mounting
Downsized design helps clearance issues w/oil pans and exhaust
Ball bearing supported armature and pinion gear
3 Hp Motor Provides Power For High Compression Engines
Gear reduction of 4.4:1 improves torque for great cranking
Downsized design helps clearance issues
Mount can be clocked to assist in mounting

from

$23.79

Spectre’s Chrysler water neck fits 1964 and later Chrysler V8 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes bolts.

Product Features:

Fits 1964 and later Chrysler V8 engines
Includes bolts
Chrome plated
Easy to install
O-ring/gasket not included

from

$16.99

Fuel pump mounting pad cover is used to cover the hole in the block when the mechanical fuel pump is removed to use an electric pump.

Product Features:

Mechanical Fuel Pump Mounting Pad Cover For Chrysler V-8ft.S

from

$30.99

Mr. Gasket has three types of exhaust gaskets–standard, Ultra Seal, and Copperseal. Use the standard for a stock rebuild and the Ultra or Copperseal for extra blowout protection.

Product Features:

Designed to provide excellent sealing and durability
Large fiber gasket material
Heat resistant
Reusable
Precision die cut for excellent fit
Limited warranty

from

$71.99

If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.

Product Features:

Improved output coil for electronic ignitions
Works w/Blaster Ignition Or MSD 5/6/7 Series
Ballast Resistor Required If Used w/Stock Points Ignition
Alkyd tower w/high dielectric properties lessens carbon tracking

from

$24.99

Available in hex head or socket head designs. The hex head is designed for easy installation of headers and heat-treated for extra strength. The special washer faced, smaller-than-standard hex head is ideal for tight spaces. Or save time, work and solve the impossible tightening problems of some header installations with socket head bolts. They help to eliminate improper gasket seal. Various sizes available in each type of bolt.

Product Features:

Quick and easy installation
Heat-treated for strength
Ideal for tight spaces
Grade 5 material
Protective black finish

from

$409.99

An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts. Ideal for use with higher compression ratio engines that

Product Features:

Best with aftermarket torque converters and 9.5:1 compression.
Great high RPM power.
Easy on valve train parts.
Can be used with mild ratio rocker arms and traditional performance valve springs.

from

$55.99

When you change a cam, you don’t need a complete engine gasket set, because you don’t have to take everything apart. Mr. Gasket cam change gasket sets are tailored to deliver just the pieces that you need when you swap bump-sticks. They include gaskets for the valve covers, intake manifold, oil pan, water pump, timing-chain cover, and fuel pump.

Product Features:

Comes with all gaskets
Fuel injector oring not included
Meets performance standards

from

$397.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 Deg Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
50-State Street Legal if Correct Carburetor Used

from

$17.99

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

from

$128.99

Product Features:

Head: 4.505″ Bore/0.038″ Thick/9.69cc Vol.
Intake: 1.23″x2.27″ Port/.030″ Thick
Exhaust: 1.84″x1.33″ Port
3/16″ Valve Cover
Multi Piece Configuration

from

$455.99

The industry standard with adjustable mechanical advance curve. Triggered by photo-optic infrared LED system. Improved combustion efficiency and economy, increased spark plug life and cold weather starting, and maintenance free operation.

Product Features:

Improved Combustion And Economy
Increased Spark Plug Life
Improved Cold Weather Starting
Maintenance Free Operation
Accurate Spark Timing
Self-Lubricating Bushings
Years Of Trouble-Free Service

from

$47.99

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$259.99

The B&M Unimatic is an ideal replacement for column shift vehicles, includes neutral safety switch, 5 foot cable and a boot and plate.

Product Features:

Ideal As Column Shift Replacement
Includes Neutral Safety Switch
Includes Black T-Handle
Backup Light Not Available
Includes 5 ft. Cable and Hardware
Includes Boot and Plate

from

$25.99

These high performance thermostats are designed to resist large variations in coolant pressures that occur at high RPM’s where coolant temperature and coolant pressure fight for control of the thermostat keeping it from opening at its designated temperature. The balanced HP thermostat features all brass and copper construction, and opens at the right temperature regardless of engine RPM.

Product Features:

High performance
Resists variations in coolant
Brass and copper construction
Opens at right temperature

from

$62.99

Available in various sizes, heights, and finishes, Spectre offers a wide variety of high performance valve covers designed to easily replace your stock covers. Designed for 1959-1980 Chrysler Slant 6 Cylinder engines, this stock profile valve cover features chrome-plated steel construction and a smooth design. With show quality construction and a sealing edge designed for an ideal fit, our valve covers are engineered to look great for applications ranging from custom builds to replacing stock equipment.

Product Features:

Designed for 1959-1980 Chrysler Slant 6 Cylinder engines
Sold in pairs
Triple chrome-plated steel construction
Stock height
Features OEM style sealing edge

from

$20.29

Fel-Pro® Performance Gaskets deliver reliable sealing under grueling racing conditions.

Product Features:

Blue Stripe® performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.