from

$53.99

304 stainless steel mesh. 5 layer construction. Most durable filters in the industry. Outperforms the others in clean air testing. Assures cleanest air possible from washable filter. Provides balance between air flow and peak filtration. Lifetime no hassle warranty.

Product Features:

Multi-Layer Construction
Most Durable Filters In The Industry
Outperforms The Others In Clean Air Testing
Assures Cleanest Air Possible From Washable Filter
Washable And Reusable
Made In The USA
Lifetime No Hassle Warranty

from

$386.99

LS1 full length engine swap header fits 66-72 Chevelle, El Camino, Monte Carlo and Sprint applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:

High Performance
Affordable
Durable 16 Gauge Material
Welds Easier
Lasts Longer
Heat Cured
High Heat Resistant

from

$85.99

The best all-round choice for vehicles with leaf or coil springs. Properly loads rear wheels to prevent over-reaction and wheel hop.

Product Features:

Excellent Weight Transfer
Lets Front End Down Quickly
Maximum Traction
Makes Vehicle Safer
Easier Control At End Of Track
Better Overall Stability

from

$347.99

Edelbrock #8832 Water Pump AMC long style 1973-later ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cooling” Water Pumps

Product Features:

Standard Impeller Rotation
0.625 in. Pilot Shaft
0.750 in. Ball/Ball Bearing
4.1875 in. Block To Hub Height
Satin Finish

from

$89.99

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$54.99

Knowing your coolant temperature can help to prevent burn injuries. Thermo Cap, with its built-in calibrated thermometer, indicates the coolant temperature. This is useful information prior to cap removal. Never attempt to remove Thermo Cap when the coolant temperature is very hot. The escaping hot coolant and steam may burn you. Check the Thermo Cap temperature indicator to determine if the coolant is cool enough to make removing Thermo Cap safe. If the coolant is very hot, then thoroughly rinse the radiator with cool water, until the coolant temperature drops into a cooler safe zone Thermo Cap’s integrated coolant reclamation valve works great with your coolant recovery system. Your radiator can reclaim coolant from your overflow bottle. Wide 30 degree to 270 degree Fahrenheit temperature range. Calibrated in centigrade and Fahrenheit. Color-coded temperature ranges. Chromed crown with a colored trim ring. Indicates coolant temperature, Helps to prevent coolant injuries, integrated coolant reclamation valve, Improves under hood appearance, Fits most domestic or import vehicles and various valve pressures available.

Product Features:

Indicates coolant temperature
Helps to prevent coolant injuries
Integrated coolant reclamation valve
Improves under hood appearance
Fits most domestic vehicles
Built in calibrated thermometer

from

$35.99

OilPanGasketSet

from

$40.99

ACCEL’s super stock is the high-performance replacement for OE canister style coils. Improves starting, idle, throttle response and top RPM power. Works with OE ignitions and computers. Alkyd tower prevents flash over. Uses OE leads. Comes in chrome.

Product Features:

42000 Volts
Effective To 6500 RPM
Quicker Starting
Improved Throttle Response
Higher RPM Power
Can Finished In Yellow

from

$40.99

Mr. Gasket standard intake gasket sets are manufactured from a blend of nitrile rubber and fiber, for excellent sealing and durability. They’re precision die-cut for each specific application to ensure a great fit, and can be custom-trimmed for modified ports where needed. The sets come complete with all necessary seals and block-off plates.

Product Features:

Forms an airtight leak proof seal
Precision die cut for excellent seal and fit
Can be trimmed to meet your specifications

from

$497.99

Hays aluminum flywheels are manufactured from certified billet material that will not break up under the stress of high RPM and severe punishment of racing. Features replaceable steel surface insert. Precision balanced to either neutral (internal) or Detroit (external) specifications. Meets SFI specification 1.1 for racing.

Product Features:

Certified Billet Material
Borg and Beck Clutch Pattern
Long-Style Clutch Pattern
Ring Gear Securely Mounted To Prevent Spinning

from

$592.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 deg. Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
50-State Street Legal if Correct Carburetor Used
Not for Stock Motorcraft Spread Bore Carburetor
Two Center Bolt Holes are Offset

from

$171.99

The Edelbrock #7372?head gaskets provide the best sealing solution and are matched to Edelbrock cylinder heads for optimal performance. Edelbrock relies on industry leading head gasket manufactures to ensure our head gasket sets will provide the best fit

Product Features:

Head: 4.275″ Bore/0.045″ Thick/10.60cc Vol.
Intake: 1.13″x2.21″ Port/.030″ Thick
Exhaust: 1.80″x1.30″ Port
3/16″ Valve Cover
Multi Piece Configuration

from

$43.99

A true performance application component for cars, trucks, hot rods and racing/competition vehicles – yet designed to be also used for street vehicles. Soft-running enough to absorb vibrations for street use yet rugged for racing use. When required- a torque resistant safety interlock design is used that is comparable in strength to those too hard-running metal mounts. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal motor mounts. The popular early style mounts for General Motors vehicles are available in either zinc or chrome metal finishes. Made of Hyper-Flex performance polyurethane. Resistant to under vehicle fluids such as: oils, coolants, road contaminants, etc.

Product Features:

Gains Both Performance and Longevity
Will Handle Any and All Torque
Out Lasts Rubber

from

$10.49

Product Features:

SOLID SPACER FORD 8.8″ & 9″

from

$25.99

The special self locking oil pan bolts, use a smaller-than-standard hex head is ideal for tight spaces. Because of the hex flange head design, it will not fall back into the socket wrench, allowing for easier installation. Special under head serrations prevent loosening and the wide flange head distributes uniform clamping pressure for an ultra gasket seal. Bolts are zinc plated, grade 5.

Product Features:

Ideal For Tight Spaces
Serrations Prevent Loosening
Flange Distributes Pressure
Zinc Plated Bolts
Grade 5 Material
Easy Installation

from

$64.99

Available in various sizes, heights, and finishes, Spectre offers a wide variety of high performance valve covers designed to easily replace your stock covers. Designed for AMC/Jeep V8 engines, this valve cover features triple chrome-plated steel construction. Sold in pairs, this standard height cover is built to provide optimum function. With show quality construction and a sealing edge designed for an ideal fit, our valve covers are engineered to look great for applications ranging from custom builds to replacing stock equipment.

Product Features:

Designed for AMC/Jeep V8 engines
Sold in pairs
Triple chrome-plated steel construction
Stock height
Features OEM style sealing edge

from

$25.99

Product Features:

Service Part
Makes Connections Quick And Easy

from

$46.99

ACCEL high-performance 32 ounce points resist point float up to 6,500 RPM. Extra-thick contact arms prevent flexing. Large tungsten contacts provide crisp circuit-breaking for peak coil output. Phenolic rubbing blocks endure heavy spring loads.

Product Features:

Extra Thick Contact Arms
Large Radius Tungsten Contacts
High Strength Phenolic Rubbing Blocks
Prevents Points Float
Moisture-Proof Buna-N Condenser

from

$141.99

These ACCEL wire sets are custom tailored for race engines and their builders. The oversize 8.8 mm wire is rated for 600 degrees Fahrenheit and 60kV. Resists heat, chemicals and moisture. High density insulation eliminates arcing. Route over and under headers.

Product Features:

150 Ohms Per Foot
8.8mm Oversize Silicone Jacket

from

$99.99

Mallory distributor gears are precision machined from alloy steel in our factory to exact original equipment specs. For use with cast flat tappet hydraulic/mechanical cams and austempered ductile iron roller cams.

Product Features:

Replacement Distributor Gear

from

$31.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

from

$353.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched To Performer Intakes PN[2131/3731]
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$40.99

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$40.99

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$15.49

Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA. Limited five year Manufacturer’s warranty.

Product Features: