1973 Pontiac Grandville Air Intakes
Find Your Specific 1973 Pontiac Grandville Air Intakes
Below you will find various in-demand Pontiac Air Intakes, components and accessories for your 1973 Grandville. Advance Auto Parts has popular Grandville parts like Air Cleaner Parts, Carburetor Parts, Carburetor Kits and more. You’ll also find aftermarket and OEM Air Intakes for other Grandville model years including
1971,
1972,
1974,
1975 and more. Select a category of 1973 Pontiac Grandville Air Intakes below and start saving instantly.
Popular 1973 Pontiac Grandville Air Intakes Categories
Essential Air Intakes for 1973 Pontiac Grandvilles
Edelbrock – Standard Flow Carburetor Power Valve #12635 Single Stage 3.5in Hg (Part No.12635)
from
$16.99
The Edelbrock #12635 Single Stage 3.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate. During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation
Product Features:
See More
Product Features:
- Gasket Or Seal Included
- 3.5 in. Hg Opening Vacuum
- Single Stage
- Standard Flow Type
- Made In The USA
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$12.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Edelbrock – Carburetor Gasket Kit #12380 Fits 4150 And 4160 Carburetors (Part No.12380)
from
$17.99
Product Features:
See More
- The Edelbrock #12380 Metering Block gasket is made of black nitrile material and will ensure a leak-free seal from your Carb to the metering block.
- The Edelbrock #12380 Metering Block gasket will fit 4150 &4160 Carburetors.
- These will not work with accelerator pump transfer tubes.
Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)
from
$62.99
Product Features:
See More
- Customize Carburetor Calibration and Performance
- Owners Manual has Assembly Help
- Includes Metering Rod Retaining Spring
- Includes Metering Rods
- Includes Metering Jets
- Includes Step-Up Springs
Edelbrock – Intake Manifold Gasket for 1961-79 3626-389-400-421-428-455 Pontiac (Part No.7280)
from
$28.99Product Features:
- Clean Positive Seal
- Embossed Silicone Bead Surrounding The Port
- Matched To Manifolds And Cylinder Heads
Wells Vehicle Electronics – Carburetor Tune-Up Kit (Part No.2G1878)
from
$33.99
WVE is a leading source of advanced vehicle electronics components for replacement applications in the automotive aftermarket and original equipment applications. WVE offers high-technology manufacturing along with innovative solutions and improvements to OE designs. Every component either matches or improves on the OE design to ensure fast, easy installation, superior performance and reliability.
See More
Carquest – Carburetor Choke Pull-Off (Part No.779-106)
from
$42.05
Carquest distributes a full line of engine management products, providing the aftermarket with premium quality and comprehensive coverage.
See More
Edelbrock – Carburetor Accelerator Pump Cam Kit #12403 for 2300, 4150, And 4160 Carburetors (Part No.12403)
from
$40.99
The Edelbrock #12403 Accelerator Pump Cam Kit Assortment Package of 8. These accelerator pump cams will have different shapes and profiles, allowing you to fine tune the accelerator pump’s performance to the engine’s requirements. Cam “lift” will directly
Product Features:
See More
Product Features:
- Multi-Color
- Plastic Material
- Fits Holley® 2300, 4150, And 4160 Carburetors
- Set of 8
- Made In The USA
Felpro – Carburetor Mounting Gasket (Part No.60397)
from
$12.79
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Felpro – Carburetor Mounting Gasket (Part No.60340)
from
$5.99
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Edelbrock – Standard Main Jet Carburetor Metering Jet #12456 Size .055 (Pair) (Part No.12456)
from
$13.99
The Edelbrock 94 #12456 Carburetor Jets .056″ Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 56 Maximum Jet Size
- 0.055 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Standard Main Jet Carburetor Metering Jet #12458 Size .057 (Pair) (Part No.12458)
from
$13.99
The Edelbrock 94 #12458 Carburetor Jets .058″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 58 Maximum Jet Size
- 0.057 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Performer 14063 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Inlet, Blk (Part No.14063)
from
$543.99
The Edelbrock 14063 Performer Series 600 CFM electric choke black powder coated carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day.
Product Features:
See More
Product Features:
- Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
- Electric Choke, Black
- 4 Barrel Count
- Square Bore
United Carb – Remanufactured Carburetor 4 Barrel (Part No.14-4164)
from
$300.99
Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.
See More
Edelbrock – Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip (Part No.12605)
from
$20.99
The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23
Product Features:
See More
Product Features:
- Center Hung Floats
- 0.11 in. Needle Diameter
- Viton® Needle Material
- Sold Individually
- Non-Adjustable Type
Carquest – Needle and Seat (Part No.93-554R)
from
$9.49
High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.
Product Features:
See More
Product Features:
- Designed to OE standards for ease of installation
Edelbrock – Torker II Intake Manifold Small-Block Chevy (Part No.5001)
from
$267.99
2500-6500 RPM high-performance street engines. Single-plane low-rise intake good for high RPM. Ideal for applications with limited hood clearance. For top-end HP and adequate throttle response. Not for mileage or emissions applications. For trucks or vans use PN(2701) instead. Not for LT1 or Chevy bowtie heads. Not for 1987 and later stock aluminum heads. Available in cast or polished.
Product Features:
See More
Product Features:
- 2500 to 6500 RPM High Performance Street Engines
- Single-Plane Low-Rise Intake Good for High RPM
- Ideal for Applications with Limited Hood Clearance
- For Top-End HP and Adequate Throttle Response
- Not for Mileage or Emissions Applications
- For Trucks or Vans Use PN[2701] Instead
- Not for LT1 or Chevy Bowtie Heads
- Not for 1987 and Later Stock Aluminum Heads
Edelbrock – Performer RPM AIR-Gap Small Block Chevy Dual-Quad Intake Manifold (Part No.7525)
from
$484.99
Air gap cooler and denser mixture for more power. Street and high performance compatible. Available in cast, polished and endurashine finish.
Product Features:
See More
Product Features:
- Based on C26 Low Profile with Unique Air Gap
- Air Gap Cooler and Denser Mixture for More Power
- 1.625 in. Taller Than Low-Profile PN[5425]
- Also Available In EnduraShine Finish PN[75254]
- Also Available As Complete Kit PN[2025/20254]
- Best When Matched with Edelbrock 500cfm Carburetor
- Use Fuel Line Kit PN[8088/8091]
- Use Progressive Throttle Linkage Kit PN[7094]
Felpro – Air Cleaner Mounting Gasket (Part No.60038)
from
$3.29
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific, providing unsurpassed quality for a seal you can trust
- Validated for fit, form, and function
- Engineered for the sealing repair environment
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Edelbrock – Carb Needle & Seat Hardware Kit #12600 FOR Holley Carb w/ Center Hung Fuel Bowl (Part No.12600)
from
$13.99
The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45
Product Features:
See More
Product Features:
- Fits Holley® Carburetors With Center Hung Fuel Bowl
- Includes Adjusting Nut
- Includes Locking Screw
- Includes O-Ring
- Includes Washers
Spectre – Bolt Kit Intake Hex Head (Part No.4652)
from
$9.99
Spectre’s Intake Bolt and Washer Set is engineered to provide premium quality hardware for Chevrolet 265-400 and Chrysler 273-440 small block engines. Measuring 3/8 inch-16 by 1 inch, these grade 5 bolts feature a corrosion resistant zinc-plated finish and hex heads to ensure easy installation. This kit includes 12 bolts and washers.
Product Features:
See More
Product Features:
- Designed for Chevrolet 265-400 and Chrysler 273-440 small block engines
- 3/8 inch-16 by 1 inch bolts
- Kit includes 12 bolts and washers
- Manufactured from high quality steel
- Bolts feature hex heads
ARP Auto Racing – For Use With Chevy 265/ 400 Cubic", Hex Style Head Type, Polished, Ss (Part No.434-2001)
from
$44.99
Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.
Product Features:
See More
Product Features:
- Nominally Rated At 170,000 PSI Tensile Strength
- Precision Machined Threads For Secure Engagement, And Would not Rust
- Wide Under Head Flange And Companion Washers Provide Even Load Distribution
- Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
- Facilitates Optimum Sealing Of Gasket Surfaces
- 1″ Long
Edelbrock – Fuel Bowl Inverted Flare Fuel Inlet Fitting #12415 (Part No.12415)
from
$20.99
Edelbrock part #12415 Fuel Bowl Inverted Flare Fitting is a 3/8″ inverted flare fuel inlet fitting. The fitting is designed for use with Holley 2300, 4150, 4150HP and 4160 (center hung floats only), 4500, 4500HP and Rochester Quadrajet applications up to
Product Features:
See More
Product Features:
- Brass Material
- 3/8 in. Single Barb
- 7/8-20 in. Male End
- 5/8-18 in. Female Flare
- With 3/8 in. Tube
Edelbrock – Pro-Flo Black 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1223)
from
$47.99
Product Features:
See More
- Edelbrock triple chrome-plated round air cleaner #1223 work with all popular 5-1/8″ diameter Carburetors (Performer Series, Thunder Series AVS, Holley, Thermo-Quad, Quadra jet and Carter AFB).
- The 10″ and 14″ models have knock-outs in the air cleaner base for use with Edelbrock crank case ventilation adapter #1205 (sold separately).
- #1208, #1209 and #1221 fit all Edelbrock Carburetors.
- Heights of air cleaners are in parentheses, measured from the gasket flange to the top of the supplied retaining nut.
- Dimensions are accurate within 1/8″.
Edelbrock – Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1221)
from
$43.99
Stamped from 18 gauge steel. Triple-chrome plated. High quality finish. Great looks. Works with all 5.152 inch carburetors. Base knock-outs for use with crankcase ventilation.
Product Features:
See More
Product Features:
- Stamped From 18-Gauge Steel
- Triple-Chrome Plated
- High-Quality Finish
- Great Looks
- Works With All 5.125 in. Carbs
- Base Knock-Outs For Use w/Crankcase Ventilation
Edelbrock – Pro-Flo 1000 Series Chrome Air Cleaner with Foam Element with 5-1/8" Air Horn (Part No.1002)
from
$31.99Product Features:
- Super Flow; Good Filtration
- Urethane Foam Element
- Strong Metal Inner Frame
- Performance Benefits
- Cleans With Soap and Water
- Low Maintenance Cost
- Simple To Install
- Nicely Finished; Low Profile
Upgrade your 1973 Pontiac Grandville with Top-Quality Air Intakes
When it comes to maintaining or upgrading your 1973 Pontiac Grandville, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Pontiac or enhancing its overall performance, Air Intakes are key to keeping your Grandville functioning at its best. At Advance Auto Parts, we offer a wide selection of 54 Air Intakes for the 1973 Pontiac Grandville, designed to meet your needs without breaking the bank.
From
Air Cleaner Part
replacements to
Carburetor Parts
upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.
Affordable Prices and Wide Selection
Shopping for Air Intakes for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Air Intakes for your 1973 Pontiac Grandville at great prices.
Our Air Intakes inventory for this model
ranges from just $3.29 to $589.99, with
an average price of $171.93.
Our 54 Air Intakes in stock come from 6 trusted brands, so you’re sure to find the right part for your 1973 Pontiac Grandville without overspending.
Top Brands and High Customer Satisfaction
Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1973 Pontiac Grandville, we stock popular OEM and aftermarket Air Intakes from top names
like FELPRO Edelbrock, and more.
FELPRO Air Intakes
start at just $3.29 and boast an impressive 5 stars average rating from customers.
With 507 customer reviews and counting, our 1973 Pontiac Grandville Air Intakes have a strong track record of reliability, ensuring you can trust your purchase.
Explore Related Parts and More
While you’re here, don’t forget to check out other essential categories that go hand in hand with Air Intake upgrades. Explore related part types like Batteries and Chargers, Fluids and Chemicals
and more to make sure your 1973 Pontiac Grandville is always ready to roll. We’re committed to providing you with everything you need to keep your Grandville in top shape, all in one place.
Start shopping confidently below for your 1973 Pontiac Grandville!
Best-Selling Air Cleaner Parts for 1973 Pontiac Grandvilles
Enhance the driving experience in your Pontiac with 4 quality Air Cleaner Part components, starting at $3.29.
Felpro – Air Cleaner Mounting Gasket (Part No.60038)
from
$3.29
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific, providing unsurpassed quality for a seal you can trust
- Validated for fit, form, and function
- Engineered for the sealing repair environment
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Edelbrock – Pro-Flo Black 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1223)
from
$47.99
Product Features:
See More
- Edelbrock triple chrome-plated round air cleaner #1223 work with all popular 5-1/8″ diameter Carburetors (Performer Series, Thunder Series AVS, Holley, Thermo-Quad, Quadra jet and Carter AFB).
- The 10″ and 14″ models have knock-outs in the air cleaner base for use with Edelbrock crank case ventilation adapter #1205 (sold separately).
- #1208, #1209 and #1221 fit all Edelbrock Carburetors.
- Heights of air cleaners are in parentheses, measured from the gasket flange to the top of the supplied retaining nut.
- Dimensions are accurate within 1/8″.
Edelbrock – Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1221)
from
$43.99
Stamped from 18 gauge steel. Triple-chrome plated. High quality finish. Great looks. Works with all 5.152 inch carburetors. Base knock-outs for use with crankcase ventilation.
Product Features:
See More
Product Features:
- Stamped From 18-Gauge Steel
- Triple-Chrome Plated
- High-Quality Finish
- Great Looks
- Works With All 5.125 in. Carbs
- Base Knock-Outs For Use w/Crankcase Ventilation
Edelbrock – Pro-Flo 1000 Series Chrome Air Cleaner with Foam Element with 5-1/8" Air Horn (Part No.1002)
from
$31.99Product Features:
- Super Flow; Good Filtration
- Urethane Foam Element
- Strong Metal Inner Frame
- Performance Benefits
- Cleans With Soap and Water
- Low Maintenance Cost
- Simple To Install
- Nicely Finished; Low Profile
Most Popular 1973 Pontiac Grandville Carburetor Parts
Customize your Pontiac with 32 Carburetor Parts products
like Carburetors,
Carburetor and Injector Mount Gaskets, and
Carburetor Accelerator Pump Diaphragms, all
priced under $589.99.
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$12.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Edelbrock – AVS2 1906 Carburetor: 650 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1906)
from
$446.99
The Edelbrock AVS2 Series #1906 is a satin-finished four-barrel carburetor with electric choke that is designed and calibrated for optimum street performance in engines that require an air-fuel flow of 650 CFM. The AVS2 is a perfect replacement or upgrade that features annular flow primary boosters with a new calibration for improved off-idle and cruising performance. The annular flow booster design delivers improved fuel atomization to eliminate flat spots that may be encountered as the carburetor transitions from idle to full throttle. Each annular flow booster features eight equally spaced orifices to improve fuel metering from idle to the main circuit. The improved flow metering makes this carburetor ideal for use with a wide variety of small- and big-block engines with either dual- or single-plane intake manifolds. The Edelbrock AVS2 #1906 includes both timed and full vacuum ports for ignition advance. It comes with: .101 primary and.098 secondary metering jets; .070 x .037 metering rods; orange (5″ Hg) step-up spring. Use our Carburetor Stud Kits #8008 or #8024 if needed. Match with a variety of manifolds that include Edelbrock Performer, Performer EPS, RPM Air-Gap, Performer RPM, Torker II or other brands of similar design. For a black-finished AVS2 with electric choke, order part #19063.
Product Features:
See More
Product Features:
- Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
- Electric Choke
- 4 Barrel Count
- Square Bore
Edelbrock – Performer Carburetor #9906 600 CFM With Electric Choke, Satin Finish (Non-EGR) (Part No.9906)
from
$397.99
Burnished aluminum. GM/MAC- style throttle linkage. Electric choke installed from factory. Easy tuning with 2 piece design. Smooth secondary transition. Both timed for full vacuum ports. Includes PCV outlet.
See More
Edelbrock – Performer Carburetor #9905 600 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.9905)
from
$397.99
Burnished aluminum. GM/MAC- style throttle linkage. Electric choke installed from factory. Easy tuning with 2 piece design. Smooth secondary transition. Both timed for full vacuum ports. Includes PCV outlet.
See More
Edelbrock – AVS2 1905 Carburetor: 650 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1905)
from
$407.99
orange (5″ Hg) step-up spring. Use our Carburetor Stud Kits #8008 or #8024 if needed. Match with a variety of manifolds that include Edelbrock Performer, Performer EPS, RPM Air-Gap, Performer RPM, Torker II or other brands of similar design. For a black-f
Product Features:
See More
Product Features:
- Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
- Manual Choke
- 4 Barrel Count
- Square Bore
Edelbrock – Standard Flow Carburetor Power Valve #12665 Single Stage 6.5in Hg (Part No.12665)
from
$16.99
Product Features:
See More
- The Edelbrock #12665 Single Stage 6.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
- During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.
Felpro – Carburetor Mounting Gasket (Part No.60061-1)
from
$9.79
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Edelbrock – Fuel Bowl Inverted Flare Fuel Inlet Fitting #12415 (Part No.12415)
from
$20.99
Edelbrock part #12415 Fuel Bowl Inverted Flare Fitting is a 3/8″ inverted flare fuel inlet fitting. The fitting is designed for use with Holley 2300, 4150, 4150HP and 4160 (center hung floats only), 4500, 4500HP and Rochester Quadrajet applications up to
Product Features:
See More
Product Features:
- Brass Material
- 3/8 in. Single Barb
- 7/8-20 in. Male End
- 5/8-18 in. Female Flare
- With 3/8 in. Tube
Edelbrock – Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip (Part No.12605)
from
$20.99
The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23
Product Features:
See More
Product Features:
- Center Hung Floats
- 0.11 in. Needle Diameter
- Viton® Needle Material
- Sold Individually
- Non-Adjustable Type
Edelbrock – Adjustable Carburetor Needle and Seat #12602 Size .097 With Viton Tip (Part No.12602)
from
$18.99
Product Features:
See More
- The Edelbrock #12602 Adjustable Inlet Needle and Seat assembly will fit Carburetors with center hung fuel bowls and can be used as replacements or performance upgrades.
- Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 4500 Series, Quick Fuel 4500, Professional Series and Q-Series, as well as various Demon Carburetors.
Edelbrock – Performer 1413 Carburetor: 800 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1413)
from
$561.99
The Edelbrock 1413 Performer Series 800 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characterist
Product Features:
See More
Product Features:
- Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
- Electric Choke
- 4 Barrel Count
- Square Bore
- Smooth Secondary Transition
- Both Timed and Full Vacuum Ports
- Includes PCV Outlet
- Can Easily Calibrate with Rods and Jets
United Carb – Remanufactured Carburetor 4 Barrel (Part No.14-4164)
from
$300.99
Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.
See More
Edelbrock – Carburetor Accelerator Pump Diaphragm #12401 50cc (Part No.12401)
from
$31.99
Edelbrock #12401 50cc Accelerator Pump Diaphragm for 4150 Carburetors. Proper installation is the responsibility of the installer. Improper installation will void your warranty and may result in poor performance and engine or vehicle damage.
Product Features:
See More
Product Features:
- Rubber Material
- For Holley®, Barry Grant, And Demon Gasoline Carburetors
- No Hardware Included
- 50cc Volume
- Made iIn The USA
Edelbrock – Standard Flow Carburetor Power Valve #12655 Single Stage 5.5in Hg (Part No.12655)
from
$16.99
Product Features:
See More
- The Edelbrock #12645 Single Stage 5.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
- During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.
Edelbrock – AVS2 650 CARBURETOR (Part No.1906-BP)
from
$589.99
AVS2 650 CARBURETOR
Edelbrock – Performer 14063 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Inlet, Blk (Part No.14063)
from
$543.99
The Edelbrock 14063 Performer Series 600 CFM electric choke black powder coated carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day.
Product Features:
See More
Product Features:
- Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
- Electric Choke, Black
- 4 Barrel Count
- Square Bore
Edelbrock – Performer 14073 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Inlet, Black (Part No.14073)
from
$527.99
Product Features:
See More
- Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
- Manual Choke, Black
- 4 Barrel Count
- Square Bore
Edelbrock – Performer 14053 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Inlet, Black (Part No.14053)
from
$492.99
The Edelbrock 14053 Performer Series 600 CFM manual choke Black Powder Coated carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 14053 Performer Series 600 CFM manual choke Black Powder Coated carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.
Product Features:
See More
Product Features:
- Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
- Manual Choke, Black
- 4 Barrel Count
- Square Bore
Edelbrock – CARBURETOR (Part No.1812)
from
$443.99
New qwik-tune adjustable secondary air valve. Optional single or dual fuel inlet. Distinctive black accented hardware. No gaskets below fuel level to prevent leakage. Metering rod and step up springs can be changed easily. GM and AMC style throttle linkag
Product Features:
See More
Product Features:
- New Qwik-Tune Adjustable Secondary Air Valve
- Optional Single Or Dual Fuel Inlet
- Distinctive Black Accented Hardware
- No Gaskets Below Fuel Level to Prevent Leakage
- Metering Rod/Step Up Springs Can Be Changed Easily
- GM/AMC-Style Throttle Linkage
- Exclusive 12 Month Complete Satisfaction Warranty
Edelbrock – Reman Thunder AVS Carb #18069 650 CFM W/ Electric Choke, Satin Finish (Non-EGR) (Part No.18069)
from
$435.99
Product Features:
See More
- Satin Finish
- 4 Barrel
- Aluminum Body Material
- Electric Choke Type
- 650 cfm Maximum Flow Rating
Edelbrock – Performer Carburetor #9913 750 CFM With Electric Choke, Satin Finish (Non-EGR) (Part No.9913)
from
$427.99
Product Features:
See More
- Satin Finish
- 4 Barrel
- Annular Booster Type
- Electric Choke Type
- 750 cfm Maximum Flow Rating
Edelbrock – Thunder AVS Carburetor #1805 650 CFM, Manual, Square Bore, Polished (Part No.1805)
from
$408.99
New qwik-tune adjustable secondary air valve. Optional single or dual fuel inlet. Distinctive black accented hardware. No gaskets below fuel level to prevent leakage. Metering rod and step up springs can be changed easily. GM and AMC style throttle linkage. Exclusive 12 month complete satisfaction warranty.
Product Features:
See More
Product Features:
- New Qwik-Tune Adjustable Secondary Air Valve
- Optional Single Or Dual Fuel Inlet
- Distinctive Black Accented Hardware
- No Gaskets Below Fuel Level to Prevent Leakage
- Metering Rod/Step Up Springs Can Be Changed Easily
- GM/AMC-Style Throttle Linkage
- Exclusive 12 Month Complete Satisfaction Warranty
Edelbrock – Reman Thunder AVS Carb #18059 650 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.18059)
from
$400.99
Product Features:
See More
- Satin Finish
- 4 Barrel
- Aluminum Body Material
- Manual Choke Type
- 650 cfm Maximum Flow Rating
United Carb – Remanufactured Carburetor 2 Barrel (Part No.14-4167)
from
$367.99
Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.
See More
United Carb – Remanufactured Carburetor 2 Barrel (Part No.14-4160)
from
$231.99
Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.
See More
Edelbrock – Carburetor Accelerator Pump Cam Kit #12403 for 2300, 4150, And 4160 Carburetors (Part No.12403)
from
$40.99
The Edelbrock #12403 Accelerator Pump Cam Kit Assortment Package of 8. These accelerator pump cams will have different shapes and profiles, allowing you to fine tune the accelerator pump’s performance to the engine’s requirements. Cam “lift” will directly
Product Features:
See More
Product Features:
- Multi-Color
- Plastic Material
- Fits Holley® 2300, 4150, And 4160 Carburetors
- Set of 8
- Made In The USA
Edelbrock – Carburetor Gasket Kit #12370 Fits 2300, 4150, 4160, 4165, And Some 4500 Carbs (Part No.12370)
from
$19.99
The Edelbrock #12370 comes with fuel bowl and metering block gaskets. The Edelbrock #12370 is designed to be used with Holley 2300, 4150, 4160, 4165, and some 4500 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block, Fuel Bowl Type
- Set of 4
- Fits Holley® 2300, 4150, 4160, 4165, And Some 4500 Carburetors
- Made In The USA
Edelbrock – Standard Flow Carburetor Power Valve #12635 Single Stage 3.5in Hg (Part No.12635)
from
$16.99
The Edelbrock #12635 Single Stage 3.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate. During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation
Product Features:
See More
Product Features:
- Gasket Or Seal Included
- 3.5 in. Hg Opening Vacuum
- Single Stage
- Standard Flow Type
- Made In The USA
Edelbrock – Carb Needle & Seat Hardware Kit #12600 FOR Holley Carb w/ Center Hung Fuel Bowl (Part No.12600)
from
$13.99
The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45
Product Features:
See More
Product Features:
- Fits Holley® Carburetors With Center Hung Fuel Bowl
- Includes Adjusting Nut
- Includes Locking Screw
- Includes O-Ring
- Includes Washers
Edelbrock – Standard Main Jet Carburetor Metering Jet #12457 Size .056 (Pair) (Part No.12457)
from
$13.99
The Edelbrock 94 #12457 Carburetor Jets .057″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 57 Maximum Jet Size
- 0.056 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Standard Main Jet Carburetor Metering Jet #12456 Size .055 (Pair) (Part No.12456)
from
$13.99
The Edelbrock 94 #12456 Carburetor Jets .056″ Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 56 Maximum Jet Size
- 0.055 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Carb Power Valve Block-Off Plug #12624 For Demon, Holley, & Quick Fuel Carbs (Part No.12624)
from
$12.99
The Edelbrock 94 Carburetor power valve block off #12624 is a great way to fine tune your vintage series carburetor. These Edelbrock Power valve Block Off’s will fit Edelbrock Vintage Series 94 carburetors as well as original Holley 94’s and its later var
Product Features:
See More
Product Features:
- Fits Any Demon®, Holley®, And Quick Fuel® Carburetors
- Includes Gasket
- 1/2 in. x 28 Power Valve Thread
- For Applications That Prefer To Run Carbs Without The Power Valves
- Made In The USA
Top Picks for 1973 Pontiac Grandville Carburetor Kits
Upgrade Pontiac Grandvilles with top-quality Carburetor Kits parts, including 10 OEM and aftermarket selections for your 1973 model.
Edelbrock – Carburetor Gasket Kit #12382 Fits 2300, 4150, 4160, 4175, And 4500 Carburetors (Part No.12382)
from
$14.99
Product Features:
See More
- The Edelbrock #12382 fuel bowl gasket is designed for Holley 2300, 4150, 4160, 4175 and 4500 Carburetors.
- Kit includes two black nitrile fuel bowl gaskets.
Edelbrock – Carburetor Repair Kit #12750 Fits Most Holley 4160 Carburetors (Part No.12750)
from
$43.99
Product Features:
See More
- The Edelbrock #12750 4160 Carburetor rebuild kit is for Holley, Demon and Quick Fuel Carburetors.
- The kit comes with the necessary components to rebuild a 4160 style Carburetor.
Edelbrock – Carburetor Repair Kit #12760 Fits Most Holley 4150 Carburetors (Part No.12760)
from
$57.99
Product Features:
See More
- The Edelbrock #12760 4150 Carburetor rebuild kit is for Holley, Demon and Quick Fuel Carburetors.
- The kit comes with the necessary components to rebuild a 4150 style Carburetor.
Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)
from
$62.99
Product Features:
See More
- Customize Carburetor Calibration and Performance
- Owners Manual has Assembly Help
- Includes Metering Rod Retaining Spring
- Includes Metering Rods
- Includes Metering Jets
- Includes Step-Up Springs
Carquest – Carburetor Kit (Part No.96-208A)
from
$25.49
High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.
Product Features:
See More
Product Features:
- Designed to OE standards for ease of installation
- Designed and manufactured to our stringent quality standards at a certified facility, so you can install with confidence
- Premium components and durable materials withstand harsh engine conditions to increase longevity and lifespan
- Undergoes extensive testing and validation for proper performance and peak reliability
- As a global manufacturer of automotive aftermarket products, we maintain complete quality control throughout the manufacturing process
Wells Vehicle Electronics – Carburetor Tune-Up Kit (Part No.2G1834)
from
$49.99
WVE is a leading source of advanced vehicle electronics components for replacement applications in the automotive aftermarket and original equipment applications. WVE offers high-technology manufacturing along with innovative solutions and improvements to OE designs. Every component either matches or improves on the OE design to ensure fast, easy installation, superior performance and reliability.
See More
Wells Vehicle Electronics – Carburetor Tune-Up Kit (Part No.2G1734)
from
$27.99
WVE is a leading source of advanced vehicle electronics components for replacement applications in the automotive aftermarket and original equipment applications. WVE offers high-technology manufacturing along with innovative solutions and improvements to OE designs. Every component either matches or improves on the OE design to ensure fast, easy installation, superior performance and reliability.
See More
Wells Vehicle Electronics – Carburetor Tune-Up Kit (Part No.2G1815)
from
$26.99
WVE is a leading source of advanced vehicle electronics components for replacement applications in the automotive aftermarket and original equipment applications. WVE offers high-technology manufacturing along with innovative solutions and improvements to OE designs. Every component either matches or improves on the OE design to ensure fast, easy installation, superior performance and reliability.
See More
Wells Vehicle Electronics – Carburetor Tune-Up Kit (Part No.2G1737)
from
$25.99
WVE is a leading source of advanced vehicle electronics components for replacement applications in the automotive aftermarket and original equipment applications. WVE offers high-technology manufacturing along with innovative solutions and improvements to OE designs. Every component either matches or improves on the OE design to ensure fast, easy installation, superior performance and reliability.
See More
Edelbrock – Carburetor Gasket Kit #12371 Fits 4160 Carburetors (Part No.12371)
from
$19.99
The Edelbrock #12371 kit includes the primary fuel bowl gasket, the primary metering block gasket, the secondary metering block gasket and a metering plate gasket. The Edelbrock #12371 fits Holley 4160 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block Type
- Set of 4
- Fits Holley® 4160 Carburetors
- Made In The USA
In-Demand Carburetor Choke Parts for 1973 Pontiac Grandvilles
Select from 1 premium Carburetor Choke Parts parts for your 1973 Pontiac Grandville.
Carquest – Carburetor Choke Pull-Off (Part No.779-106)
from
$42.05
Carquest distributes a full line of engine management products, providing the aftermarket with premium quality and comprehensive coverage.
See More
Most Sold 1973 Pontiac Grandville Intake Manifold Parts
Explore our best-selling Pontiac parts for the 1973 Grandville among 7 OEM and aftermarket options starting from $28.49.
Felpro – INTAKE MANIFOLD GASKET SET (Part No.MS 90205)
from
$28.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
- ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
- REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
- EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
Edelbrock – Performer Intake Manifold for 1965-79 Pontiac 326-455 Non-EGR (Part No.2156)
from
$409.99
Product Features:
See More
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 deg. Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
ARP Auto Racing – For Use With Chevy 265/ 400 Cubic", 12 Point Head Type, Polished, With Washers (Part No.434-2101)
from
$47.99
Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.
Product Features:
See More
Product Features:
- Nominally Rated At 170,000 PSI Tensile Strength
- Precision Machined Threads For Secure Engagement, And Would not Rust
- Wide Under Head Flange And Companion Washers Provide Even Load Distribution
- Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
- Facilitates Optimum Sealing Of Gasket Surfaces
Edelbrock – Intake Manifold Gasket for 1961-79 3626-389-400-421-428-455 Pontiac (Part No.7280)
from
$28.99Product Features:
- Clean Positive Seal
- Embossed Silicone Bead Surrounding The Port
- Matched To Manifolds And Cylinder Heads
Edelbrock – Performer Intake Manifold for 1965-79 Pontiac 326-455 Non-EGR, Black Finish (Part No.21563)
from
$545.99
Edelbrock part #21563 Performer Pontiac intake manifold is designed for 1965-79 Pontiac 326-455 c.i.d. V8’s (except Ram Air V and 265/301 V8’s). Provides great throttle response for performance you can feel. Ideal for cars, 4x4s, tow vehicles, RVs and boa
Product Features:
See More
Product Features:
- Idle-5500 RPM Range
- Dual Plane Type-4150 Style Flange
- 5.5 in. Front Height, 6.05 in. Center Height, 6.6 in. Rear Height
- Black Powder Coated Finish
- Non-EGR
Edelbrock – Performer RPM Pontiac 326-455 Intake Manifold (Part No.7156)
from
$432.99Product Features:
- Best for the Ultimate in Street High-Performance
- Designed for 1500 to 6500 RPM Street-Driven Power
- Dual-Plane High-Rise Intake w/180 deg Firing Order
- Produces Incredible Top-End Horsepower
- Retains Good Throttle Response and Acceleration
- Larger Plenum and Runners Maximizes Other Upgrades
- Edelbrock Total Power Package Maximizes Gains
ARP Auto Racing – For Use With Chevy 265/ 400 Cubic", Hex Style Head Type, Polished, Ss (Part No.434-2001)
from
$44.99
Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.
Product Features:
See More
Product Features:
- Nominally Rated At 170,000 PSI Tensile Strength
- Precision Machined Threads For Secure Engagement, And Would not Rust
- Wide Under Head Flange And Companion Washers Provide Even Load Distribution
- Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
- Facilitates Optimum Sealing Of Gasket Surfaces
- 1″ Long
Top-Rated Air Intakes Brands For Your 1973 Pontiac Grandville
Shop for the best-rated brands offering Air Intakes and other products for your 1973 Pontiac Grandvilles. Below you’ll find some of our best rated Air Intakes from FELPRO and Edelbrock, and more. Air Intakes from these brands that fit a 1973 Grandville start at just $3.29 and are rated as high as 5 stars. OEM and aftermarket Air Intakes don’t get more top quality, durable, and affordable than from the brands below.
Popular FELPRO 1973 Pontiac Grandville Air Intakes
When it comes to maintaining or upgrading your 1973 Pontiac Grandville, using quality Air Intakes is essential to ensure durability and a perfect fit. FELPRO ticks all of those boxes. We offer a wide selection of FELPRO Air Intakes, specifically designed for the 1973 Pontiac Grandville. With over 3 FELPRO brand Air Intakes in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $3.29, with an average price of just $13.86. Plus, with over 40 customer reviews and an average rating of 5 stars, you can trust that our FELPRO Air Intakes will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.
Popular Edelbrock 1973 Pontiac Grandville Air Intakes
Edelbrock auto parts is one of the highest quality Air Intake brands in the market. Any 1973 Pontiac Grandville owner should feel confident when installing genuine Edelbrock parts in their vehicle. To ensure the best fit and performance for your 1973 Grandville, Advance Auto Parts carries a full inventory of 40 Edelbrock Air Intakes. Plus you will be keeping your Pontiac in peak condition while saving money because prices on these Edelbrock Air Intakes range from $12.99 to $589.99, plus, with more than 59 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Air Intakes below will deliver on both quality and value.
from
$62.99
$62.99
This product is not rated
Performer Carburetor Calibration Kit #1487 for #1406 Carburetors
“”
from
$57.99
$57.99
This product is not rated
Carburetor Repair Kit #12760 Fits Most Holley 4150 Carburetors
“”
from
$43.99
$43.99
This product is not rated
Carburetor Repair Kit #12750 Fits Most Holley 4160 Carburetors
“”
FAQs for 1973 Pontiac Grandville Air Intakes
Which Air Intakes are best-sellers for 1973 Pontiac Grandvilles?
Out of 54 Air Intakes that fit 1973 Pontiac Grandvilles, the following parts are the top sellers:
- Pro-Flo Black 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (10226962) – $47.99
- Carburetor Repair Kit #12750 Fits Most Holley 4160 Carburetors (10648540) – $43.99
- Carburetor Accelerator Pump Diaphragm #12400 30cc (10648626) – $12.99
What’s the price range for 1973 Pontiac Grandville Air Intakes?
Air Intake prices for the 1973 Pontiac Grandville start at $3.29 and go up to $589.99 for the most premium parts.
What’s the average price of a Air Intake for a 1973 Pontiac Grandville?
The average price for Air Intakes for the 1973 Pontiac Grandville is $171.93. Keep in mind the variety of part types within our Air Intake category so you are likely to find a wide range of prices across a variety of parts and components.
Does Advance Auto Parts sell Air Intakes for other Pontiac Grandville model years?
What are the cheapest Air Intakes for my 1973 Pontiac Grandville?
The cheapest 1973 Pontiac Grandville Air Intakes we carry in stock are:
- Air Cleaner Mounting Gasket (5785448) – $3.29
- Carburetor Mounting Gasket (3210138) – $9.79
- Carburetor Accelerator Pump Diaphragm #12400 30cc (10648626) – $12.99
- Carb Power Valve Block-Off Plug #12624 For Demon, Holley, & Quick Fuel Carbs (10648376) – $12.99
- Carb Needle & Seat Hardware Kit #12600 FOR Holley Carb w/ Center Hung Fuel Bowl (10648424) – $13.99
What are the top-rated Air Intakes that fit the 1973 Pontiac Grandville?
Out of 507 reviews by customers, our 1973 Pontiac Grandville Air Intakes have an average customer rating of . These are some of the highest-rated Air Intake types for the 1973 Pontiac Grandville and their top-rated products:
- Intake Manifold Parts
- INTAKE MANIFOLD GASKET SET (5184495) – $28.49
- Air Cleaner Parts
- INTAKE MANIFOLD GASKET SET (5184495) – $28.49
- Carburetor Kits
- INTAKE MANIFOLD GASKET SET (5184495) – $28.49
What types of Air Intakes do you sell for my 1973 Pontiac Grandville?
As of 2/5/25, these are some of the most in-demand types of Air Intakes for a 1973 Pontiac Grandville:
Can I get help with 1973 Pontiac Grandville Air Intake orders?
Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Pontiac Air Intakes and more.
What is your return policy for Pontiac Grandville Air Intakes?
Advance Auto Parts keeps returns simple. For new Pontiac Grandville Air Intakes and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.
