1973 Jeep Commando Differentials

Bearing race driver for Dana 44 rear. (TK 31520) No return.

Product Features:

• Bearing race driver
• Fits 31520 race
• All steel construction

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000!

Product Features:

• Fits Dana Spicer 30 with 27 spline axles
• 3.73 and up ratio only
• Patented internal design reduces common locker failures
• 8620 internals for added strength
• Assembled in the USA

Product Features:

• Outer oil slinger for Dana Spicer 25, 27, 30, 44 and 50

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

• Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
• 1/2″ head

Product Features:

• Clutch kit
• Fit Dana Spicer 44 and Chrysler 8.75″ Powr Lok positraction
• Smooth design

Dana 30 & Dana 44 roll PIN, 0.235″ DIA, for cross pin shaft.

Product Features:

• Roll pin for Dana Spicer 30 and Dana Spicer 44
• 0.235″ diameter

Air line repair kit, ZIP locker.

Product Features:

• Air line repair kit
• Includes 20′ air line and two repair fittings

Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:

• Includes four quarts of Redline Shockproof oil

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

• Fits standard rotation Dana Spicer 30
• Included are a pinion seal, axle seals, complete shim kit, marking compound and brush.

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Dana Spicer 27
• Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

• Pinion nut for Dana Spicer 25, 27, 30, 44, 50 and GM 7.75″
• 3/4″ x 16 thread

Product Features:

• MINI-INSTLTN KIT-DANA 30

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Unsurpassed quality you can trust
• Validated for fit, form and function
• Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

Set-up carrier bearing (2 bearings, no races) 25590. No return.

Product Features:

• Set up bearing kit
• Fits Dana Spicer 44
• Easily slips on and off carrier journals to allow for easier carrier shim adjustment

Product Features:

• Oil baffle for Dana Spicer 44

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

• Fits standard rotation Dana Spicer 44
• 8.50″ ring gear diameter
• 26 spline pinion
• 10 ring gear bolts
• 5.13 ratio

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings

Product Features:

• Side gear thrust washer
• Fits Dana Spicer 44 with 19 spline axles

Replacement pinion nut washer for Dana 25, 27, 30, 36, 44 & 53.

Product Features:

• Pinion nut washer for Dana Spicer 25, 27, 30, 44 and 50

7/16″ TO 3/8″ ring gear bolt spacer sleeve.

Product Features:

• Ring gear bolt sleeve
• Adapts 7/16″ to 3/8″

Yukon positraction internals for Dana 44 Dura Grip posi, 30 spline. Does not include clutches. Does NOT fit Trac Loc or Powr Lok. Fits Dura Grip ONLY.

Product Features:

• Spider gear kit
• Fits Dana Spicer 44 with Dura Grip positraction
• Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

This engine oil drain plug is designed to match the fit and function of an original equipment plug on specified vehicles. It is engineered to replace a missing or damaged plug and help ensure a secure seal.

Product Features:

• Direct replacement – this engine oil drain plug is designed to match the fit and function of an original equipment plug on specified vehicles
• Ideal solution – engineered to replace a missing or damaged plug and help ensure a secure seal
• Durable construction – designed and manufactured to strict specifications for reliable performance
• Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

• DANA-44 LATE TIMKEN MASTER KIT

Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.

Product Features:

• Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
• Left hand thread

Product Features:

• Carrier shim kit for Dana Spicer 30 and Dana Spicer 44 with 19 spline axles

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Designed to repair damaged, grooved or worn shafts
• Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
• Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
• Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
• Easy to install with removable flange and installation tool
• Installation tool reduces sleeve distortion and allows for installation without removal from the shaft