1973 Dodge B200 Van Differentials

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

• Fits Chrysler 8.75″ ’42’ case housing with 25520 carrier races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, marking compound and brush.

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits Chrysler 8.75″ ’42’ case housing with LM104912 carrier races
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

• Cover bolt for Dana Spicer 60, 70 and 80
• 3/8″

Yukon extra HD yoke for Chrysler 8.75″ with 10 spline pinion and a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Chrysler 8.75″
• 10 spline
• 1350 u-joint size
• Outside snap ring design
• 3.625″ snap ring span
• 1.188″ cap diameter
• Strap style

Dana 60 & Dana 70 Power Lok case bolt.

Product Features:

• Power Lok case bolt for Dana Spicer 60 and 70
• 7/16 x 14 thread
• 3.5″ long
• 9/16″ hex head

Pinion seal for Chrysler 8.75″ 42 housing.Yukon Mighty seal.

Product Features:

• Pinion seal
• Fits Chrysler 8.75″ with ’42’ case housing

Product Features:

• Floater roll pin
• Fits Dana Spicer 44 and Chrysler 8.75″
• Powr Lok positraction only

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

• Powr Lok button kit
• Fits Dana Spicer 30, 44 and Chrysler 8.75″

A worn or damaged differential pinion flange can lead to driveline vibrations and fluid leaks. This part is designed to match the performance of the original equipment pinion flange on specified vehicles. It has been engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is rusted, worn or damaged. It is made of rugged materials for reliable service and durability.

Product Features:

• Direct replacement – this differential pinion flange is designed to match the performance of the original equipment flange on specified vehicles
• Ideal solution – engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is worn or damaged
• Durable construction – designed and manufactured to strict specifications for reliable performance
• Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

M804049 set-up bearing (one bearing). No return.

Product Features:

• Set up bearing
• Fits HM804049 pinion bearing
• Easily slips on and off pinion journal to allow for pinion depth adjustment

Full-floating, 35 spline diameter, non-drilled blank axle shaft for Dana 60. 40″ inches long. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H axles come with a one year warranty against manufacturing defects.

Product Features:

• Pinion nut washer for Chrysler 7.25″, 8.25″, 8.75″ with 29 spline pinion, Jeep JK rear, Dana Spicer 60, 70, 70U and 70HD and 2007-2010 Ford 10.5″

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

• Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty. This is a fine spline pinion which takes a 29 spline yoke.

Product Features:

• Fits Chrysler 8.75″ “41” case housing
• 8.75″ ring gear diameter
• 29 spline pinion
• 12 ring gear bolts
• 3.55 ratio

Product Features:

• Spider gear kit
• Fits Dana Spicer 60, 30 spline open differential
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

9.25″ pinion gear thrust washer.

Product Features:

• Pinion gear thrust washer for Chrysler 9.25″ rear

Differential side bearing screw adjuster for 9.25″ Chrysler.

Product Features:

• Side adjuster for Chrysler 9.25″ rear

Seal housing for Dana 60, Zip locker, with o-rings.

Product Features:

• Seal housing for Dana Spicer 60
• Includes o-rings

This differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

• Direct replacement – this differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles
• Required replacement – when servicing the differential
• Durable construction – this part is made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Chrysler 8.75″ (coarse spline) pinion nut. 3/4″ x 16.

Product Features:

• Pinion nut
• Fits Chrysler 8.75″ with 10 spline pinion

Product Features:

• Cover gasket
• Fits Dana Spicer 60, 70, 70U and 70HD

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver selectability. The Yukon Zip locker is an air operated locker that provides selectable traction for off road or street use. This unit features 4320 Chrome Moly internals for added strength. Assembled in the USA! compressor sold separately. All Zip Lockers are backed by the best warranty in the business! All Zip Lockers come with a six (6) year warranty, including any collaterally damaged parts and associated labor, up to $2,000, for the first two (2) years. This is a narrow case locker. If you have a wide housing, please order two DS 42563 with your locker. This locker is ABS compatible.

Product Features:

• Fits Dana Spicer 60 with 35 spline axles
• 4.10 and down ratio only
• Forged case and 8620 internals for added strength
• Works with a variety of air delivery systems
• Assembled in the USA

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Chrysler 8.75″ ’41’ case
• Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

89 housing nodular Iron Drop Out case, up to 500 HP, Billet adjuster for 8.75″ Chrysler. This dropout does not come with fill plug (Part number CHY612017).

Product Features:

• Fits Chrysler 8.75″
• ’89’ case design
• Nodular iron for added strength

Product Features:

• Inner oil slinger for Dana Spicer 60

Product Features:

• Fits Chrysler 9.25″ rear with open differential
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits HM89410 race
• All steel construction