1973 Chevrolet Camaro Intake Manifold Parts
More 1973 Chevrolet Camaro Intake Manifold Parts
Find your specific 1973 Chevrolet Camaro original or aftermarket Intake Manifold Parts below. Order your parts online and have delivered to your home or pick up in-store at Advance Auto.
Essential 1973 Chevrolet Camaro Intake Manifold Parts
Felpro – Engine Intake Manifold Gasket Set (Part No.MS 95809-1)
from
$56.99
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
- ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
- REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
- EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
Felpro – Engine Intake Manifold Gasket Set (Part No.MS 98014 T)
from
$97.99
Product Features:
See More
- DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- STRONG AND DURABLE — Features molded rubber over an aluminized steel carrier which resists high heat and coolants
- SUPERIOR SEAL — Proprietary rubber sealing beads help eliminate potential leak paths for a superior seal
- EASIER TO INSTALL — Locating tabs assure proper alignment and easier installation
- PREVENTS OVERTIGHTENING — Torque limiters help eliminate overtightening and gasket splitting and extruding
- EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
- EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
Felpro – Engine Intake Manifold Gasket Set (Part No.MS 95580)
from
$31.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
- ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
- REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
- EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
Felpro – Engine Intake Manifold Gasket Set (Part No.MS 93020)
from
$40.99
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
- ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
- REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
- EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
Edelbrock – Intake Manifold replacement runner to base gaskets (Part No.6942)
from
$14.99Product Features:
- Replacement Gasket For PN[3789] Edelbrock Intake
- One Gasket Only
- Goes Between Base pn[3785] And Top PN[3789]
- Also Included in Base PN[3789]
Mr. Gasket – Ultra Seal: Intake Gasket (Part No.5820)
from
$34.99
Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.
Product Features:
See More
Product Features:
- Manufactured from cellulose/nitrile composition gasket material
- Provides excellent sealing and durability
- Silicone beading on both sides of each gasket
- Complete with manifold end seals and distributor gasket
- For OE replacement, high performance street, drag race and oval track use
Mr. Gasket – Ultra Seal: Intake Gasket (Part No.5828)
from
$40.19
Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.
Product Features:
See More
Product Features:
- Manufactured from cellulose/nitrile composition gasket material
- Provides excellent sealing and durability
- Silicone beading on both sides of each gasket
- Complete with manifold end seals and distributor gasket
- For OE replacement, high performance street, drag race and oval track use
Felpro – Intake Man. Gasket S (Part No.A8043972544FEL)
from
$46.51
Intake Man. Gasket S
Edelbrock – Intake Manifold Gasket for 1965-1990, Oval port 396-402-454 B/B Chevy (Part No.7203)
from
$32.99
Product Features:
See More
- Clean Positive Seal
- Embossed Silicone Bead Surrounding The Port
- Matched To Manifolds And Cylinder Heads
Edelbrock – Performer Intake Manifold Small-Block Chevy (Part No.3706)
from
$381.99Product Features:
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 Deg Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
- Accepts Late-Model Choke; Waterneck; and HEI
- Accepts A/C And Alternator
- Accepts Exhaust Heated Chokes and Accepts EGR
Edelbrock – Performer RPM Small Block Chevy Polished Intake Manifold (Part No.71011)
from
$578.99Product Features:
- Polished Version Of Edelbrock PN[7101]
- Polish is Hand-Buffed for Brilliant Shine
- Based on Performer RPM-Series with Unique Air Gap
- Air Gap Cooler and Denser Mixture for More Power
- Designed for 1500 to 6500 RPM Street-Driven Power
- Produces Incredible Top-End Horsepower
- Retains Good Throttle Response and Acceleration
- Larger Plenum and Runners Maximizes Other Upgrades
Edelbrock – Single-Quad Manifold and carb Kit for Big-Block Chevy Oval Port (Part No.2062)
from
$1029.99
The Edelbrock #2062 Single-Quad Manifold and carb kit is designed for Big-Block Chevy Oval Port applications. With a Manifold and Carb Kit, it’s easy to upgrade your induction system with the best combination of Edelbrock proven performance and looks in a
Product Features:
See More
Product Features:
- Satin Finish
- Single-Quad Manifold
- Thunder Series AVS2 800 cfm Carb
- Performer RPM Manifold
- Oval Port
Holley – Manifold; SBC Early DP TBI EGR (Part No.300-49)
from
$377.99
Utilizes late model alternator and A/C bracket mounting provisions. Has vacuum taps off Manifold runners. Uses cable bracket P/N 20-101 for GM 700R4 transmission. Extra installation hardware included.
Product Features:
See More
Product Features:
- High Rise Dual Plane Design
- Holley Pro-Jection Tbi Mounting Flange
- Erg Provisions
MSD Ignition – Atomic; AirForce; LS1; 2; 6; Intake Manifold (Part No.2702)
from
$1230.00
When you’re serious about power for your LS or new LT1 engine, call in the AirForce! The all-new MSD Atomic AirForce intake manifold delivers improved airflow and distribution to improve the performance of stock and modified engines. The unique bell-mouthed runner entrances maximize airflow and minimize shrouding – all while optimizing the available plenum volume for an unobstructed flow path over opposing runners. The polymer molded 2-piece design allows for easy access to the runners for porting. Atomic AirForce accepts an OEM or 103mm throttle body as well as stock or aftermarket fuel rails including MSD’s Atomic LS EFI system. The intake bolts on and is supplied with new gaskets and hardware for a direct bolt-on package.
Product Features:
See More
Product Features:
- Polymer Material Resists Heat Soak
- 103mm Throttle Bore For Greater Air Flow
- Direct Flow Path Runner Design
- Allows For The Use Of Stock Fuel Rails
Edelbrock – Pro-Flo XT Small Block Chevy LS1 EFI Intake Manifold (Part No.7139)
from
$655.99
Edelbrock part #7139 Pro-Flo XT LS1 EFI intake manifold is engineered with a large plenum and tapered runners to deliver maximum horsepower and broad torque band throughout the rpm range (1500-7000 rpm). Features a 90mm throttle bore opening and 2.75″ por
Product Features:
See More
Product Features:
- 1500-7000 RPM Range
- Single Plane Type-Throttle Body XT Style Flange
- 10.2 in. Front Height, 10.2 in. Center Height, 10 in. Rear Height
- Satin Finish
- Made In The USA
Holley – Intake Manifold (Part No.300-5)
from
$363.99
Holley products have been the undisputed leader in fuel systems for over 100 years. Holley carburetors power every NASCAR Sprint Cup team and every NHRA Pro-Stock champion. Holley’s products include performance fuel pumps, fuel injection, intake manifolds, cylinder heads & engine dress-up products for street performance, race and marine applications. As a single solution, or partnered with products from other Holley companies, Hooker Headers, Flowtech Headers, NOS, Weiand, or Earl’s, Holley products can give you the edge you need over the competition.
Product Features:
See More
Product Features:
- Single Plane/Open Plenum Design
- Deep Plenum Design With Isolated Runners
- 4150 Square Bore Carburetor Mounting Flange
- Power Band 4500-8500 rpm
- Height Front 4.77 in. Rear 6.16 in.
- Port Size 2.30 in. Height 1.60 in. Width
- 50 State Legal
Edelbrock – Pro-Flo XT Small Block Chevy LS1 EFI Black Intake Manifold (Part No.71393)
from
$823.99
Edelbrock part #71393 Pro-Flo XT LS1 EFI intake manifold is engineered with a large plenum and tapered runners to deliver maximum horsepower and broad torque band throughout the rpm range (1500-7000 rpm). Features a 90mm throttle bore opening and 2.75″ po
Product Features:
See More
Product Features:
- 1500-7000 RPM Range
- Single Plane Type-Throttle Body XT Style Flange
- 10.2 in. Front Height, 10.2 in. Center Height, 10 in. Rear Height
- Black Powder Coated Finish
- Made In The USA
Edelbrock – Performer EPS Manifold w/Oil Fill Tube for Small-Block Chevy, Black Finish (Part No.27033)
from
$445.99
Edelbrock part #27033 Performer EPS intake manifold is designed for 1986 and earlier 262-400 cubic-inch Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent thr
Product Features:
See More
Product Features:
- Idle-5500 RPM Range
- Dual Plane Type-4150 Style Flange
- 3.74 in. Front Height, 4.27 in. Center Height, 4.8 in. Rear Height
- Black Powder Coated Finish
- Non-EGR W/ Oil Fill Tube
ARP Auto Racing – For Use With Chevy 396/ 454 Cubic", 12 Point Head Type, Polished, With Washers (Part No.435-2101)
from
$59.99
Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.
Product Features:
See More
Product Features:
- Nominally Rated At 170,000 PSI Tensile Strength
- Precision Machined Threads For Secure Engagement, And Wont Rust
- Wide Under Head Flange And Companion Washers Provide Even Load Distribution
- Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
- Facilitates Optimum Sealing Of Gasket Surfaces
Spectre – Bolt Kit Intake Hex Head (Part No.4652)
from
$9.99
Spectre’s Intake Bolt and Washer Set is engineered to provide premium quality hardware for Chevrolet 265-400 and Chrysler 273-440 small block engines. Measuring 3/8 inch-16 by 1 inch, these grade 5 bolts feature a corrosion resistant zinc-plated finish and hex heads to ensure easy installation. This kit includes 12 bolts and washers.
Product Features:
See More
Product Features:
- Designed for Chevrolet 265-400 and Chrysler 273-440 small block engines
- 3/8 inch-16 by 1 inch bolts
- Kit includes 12 bolts and washers
- Manufactured from high quality steel
- Bolts feature hex heads
ARP Auto Racing – For Use With Chevy 265/ 400 Cubic", 12 Point Head Type, Polished, With Washers (Part No.434-2101)
from
$46.49
Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.
Product Features:
See More
Product Features:
- Nominally Rated At 170,000 PSI Tensile Strength
- Precision Machined Threads For Secure Engagement, And Would not Rust
- Wide Under Head Flange And Companion Washers Provide Even Load Distribution
- Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
- Facilitates Optimum Sealing Of Gasket Surfaces
Mr. Gasket – Intake Manifold Bolts (Part No.955G)
from
$15.49
These grade 5 socket head bolts are zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8-16 x 1 inch bolts & washers.
Product Features:
See More
Product Features:
- Grade 5 socket head bolts are zinc plated for protection and appearance
- Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds
- Washers Included
ARP Auto Racing – For Use With Chevy 265/ 400 Cubic", Hex Style Head Type, Polished, Ss (Part No.434-2001)
from
$46.49
Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.
Product Features:
See More
Product Features:
- Nominally Rated At 170,000 PSI Tensile Strength
- Precision Machined Threads For Secure Engagement, And Would not Rust
- Wide Under Head Flange And Companion Washers Provide Even Load Distribution
- Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
- Facilitates Optimum Sealing Of Gasket Surfaces
- 1″ Long
Mr. Gasket – Intake Manifold Bolt Set – Chevrolet Small Block – Socket Head 3/8"-16 X 1" Bolts & Washers (Part No.956G)
from
$17.49
These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers
Product Features:
See More
Product Features:
- Zinc plated to resist corrosion and provide a clean professional appearance
- Made from Grade 5 steel for strength and durability
- Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
- Allen (socket) Head
- Zinc Plated For Protection
ARP Auto Racing – For Use With Chevy 396/ 454 Cubic Inch, Hex Head, Polished, Ss, With Washers (Part No.435-2001)
from
$59.99
Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.
Product Features:
See More
Product Features:
- Nominally Rated At 170,000 Psi Tensile Strength
- Precision Machined Threads For Secure Engagement, And Would not Rust
- Wide Under Head Flange And Companion Washers Provide Even Load Distribution
- Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
- Facilitates Optimum Sealing Of Gasket Surfaces
Popular 1973 Chevrolet Camaro Intake Manifold Parts Categories
1973 Chevrolet Camaro Intake Manifold Parts
Maybe you’re in the middle of a full rebuild of that 1973 Chevrolet Camaro. Maybe you just need a couple of Intake Manifold Parts. Either way, Advance Auto Parts has 30 different Intake Manifold Parts in our inventory ranging from $9.99 to $1,776.99. That means you can find the exact parts or products you need to keep that 1973 Chevrolet Camaro running smoothly.
Intake Manifold Parts are only as good as their brand. We stock 7 different brands to make sure you have plenty of trusted parts to choose from for your 1973 Chevrolet Camaro. Felpro, Mr. Gasket, and Spectre are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!
We know you’ll find the perfect Intake Manifold Parts for your 1973 Chevrolet Camaro, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 753 reviews in this category, some of the top rated parts include Keith Dorton Series; Intake Manifold with 5.0 stars.
So if you’re in the market for aftermarket Intake Manifold Parts to keep your 1973 Chevrolet Camaro rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!
Intake Manifold Parts Brands To Make Your 1973 Chevrolet Camaro Last
Simple repair, complete replacement, or a full rebuild. No matter the job, your 1973 Chevrolet Camaro demands trusted brand parts and products to keep it running. Many trusted brands of Intake Manifold Parts make up Advance Auto Parts’ inventory, and all are ready to help make your Camaro the best it can be. Be sure to browse some of our top Intake Manifold Parts brands and parts.
Popular Edelbrock Intake Manifold Parts
We carry Edelbrock parts in our stock across Intake Manifolds categories, plus more. For a 1973 Chevrolet Camaro, our most popular Edelbrock Intake Manifold Parts include:
from
$257.99
(3)
Performer Intake Manifold for 1955-86 Small-Block Chevy, Satin Finish
Intake Manifolds
Top 1973 Chevrolet Camaro Intake Manifold Parts from Felpro
Felpro products are another trusted brand when it comes to Intake Manifold Parts for your 1973 Chevrolet Camaro. Popular Felpro parts include:
FAQs for 1973 Chevrolet Camaro Intake Manifold Parts
What are the most purchased Intake Manifold Parts for the 1973 Chevrolet Camaro?
Out of 30 Intake Manifold Parts for the 1973 Chevrolet Camaro, the most popular in our inventory are:
from
$17.49
This product is not rated
Intake Manifold Bolt Set – Chevrolet Small Block – Socket Head 3/8"-16 X 1" Bolts & Washers
Intake Manifold Bolt Sets
What are the top-rated 1973 Chevrolet Camaro Intake Manifold Parts?
Top-rated Intake Manifold Parts for your 1973 Chevrolet Camaro based on customer reviews/ratings are:
from
$491.99
(1)
Keith Dorton Series; Intake Manifold
“This is a excellent choice for dirt circle track racing for sbc in the 350-377 range.”
