from

$27.99

Product Features:

Brand may vary by location

from

$7.99

14T side gear Thrust washer.

Product Features:

Side gear thrust washer
Fits GM 10.5″ 14 bolt truck

from

$205.99

Product Features:

GM10.5″ 14 BOLT OPEN EMPTY CASE 4:56 & UP

from

$18.09

Mr. Gasket Axle Housing/Differential Cover or Rear End Gaskets are manufactured from a .047 inch thick cellulose/nitrile composite gasket material for excellent sealing and durability. They are precision die-cut for an excellent fit. Fits 1964-1970 Chevrolet 8.2 inch 10 bolt & 1970-1981 GM 8.5 inch ring gear

Product Features:

.047″ thick cellulose/nitrile composite gasket material
Precision die cut
Reusable

from

$18.99

Product Features:

Bulkhead quit connect fitting

from

$509.99

Product Features:

Trac Loc positraction carrier case
Does not include spider gears
Fits Dana Spicer 60
4.10 and down ratio only
ABS and non-ABS compatible

from

$684.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

Fits standard rotation Dana Spicer 60
9.75″ ring gear diameter
29 spline pinion
12 ring gear bolts
3.73 ratio

from

$13.49

Product Features:

Brand may vary by location

from

$266.99

Yukon forged replacement yoke for Dana 60, stronger than billet, with a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 60, 70, 70U and 70HD
29 spline
1350 u-joint size
3.625″ snap ring span
1.188″ cap diameter
Outside snap ring design
U-bolt style

from

$225.99

Product Features:

Fits Dana Spicer 60 rear
Uses Koyo bearings and races
Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, marking compound and brush.

from

$23.99

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o

from

$232.99

Full-floating, 35 spline diameter, non-drilled blank axle shaft for Dana 60. 40″ inches long. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H axles come with a one year warranty against manufacturing defects.

from

$219.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$659.99

Yukon replacement positraction internals for Dana 60 (full- and semi-floating) with 35 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit includes clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Dana Spicer 60 with Trac Loc positraction with 35 spline axles
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$295.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Dana Spicer 60 rear
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$44.99

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

Includes three quarts of conventional oil

from

$156.99

Dana 60 & Dana 70 Power Lok cross pin shaft (TWO needed).

Product Features:

Cross pin shaft
Fits Dana Spicer 60 and 70
Powr Lok positraction only

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$7.99

10.5″ GM 14 bolt truck crush sleeve, 1988 & OLDER. Approx 0.825″ long.

Product Features:

Crush sleeve for 1988 and down GM 10.5″ 14 bolt truck
0.825″ tall

from

$40.99

GM HO72 (Yukon gear ONLY ) pinion depth shims.

Product Features:

Pinion depth shim kit
Fits GM HO72

from

$463.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!