1973 Buick Centurion Performance and Racing Products

Below you will find various in-demand Buick Performance and Racing Products, components and accessories for your 1973 Centurion. Advance Auto Parts has popular Centurion parts like Performance Oil Filters, Performance Air Filters, Performance Fuel Systems and more. You’ll also find aftermarket and OEM Performance and Racing Products for other Centurion model years including 1971 1972 and more. Select a category of 1973 Buick Centurion Performance and Racing Products below and start saving instantly.

Please Select your Vehicle to See Exact Fit Parts

Popular 1973 Buick Centurion Performance and Racing Products Categories

Performance Oil Filters

Performance Carburetors

Performance Engine Coolant Thermostats

Performance Intake Manifolds

Performance Fuel Pumps

Performance Air Filters

Performance Coils

Performance Distributor Cap and Rotor Kits

Performance Shifters

Performance Distributors

Performance Transmission Dipstick Tubes

Performance Valve Covers

Performance Engine Water Pumps

Performance Water Outlets

Performance Radiator Caps

Performance Engine Cylinder Head Gaskets

Performance Engine Camshaft and Lifter Kits

Performance Engine Intake Manifold Gaskets

Performance Coil Spring Insulators

Performance Clutch Pressure Plate and Disc Sets

Performance Engine Timing Sets and Components

Performance Engine Valve Springs

Performance Engine Valve Cover Gasket Sets

Performance Flywheel and Flexplates

Performance Exhaust Manifold Gaskets

Performance Posi Units and Components

Performance Timing Covers and Tabs

Performance Ignition Kits

Performance Engine Rocker Arms

Performance Exhaust Header Hardware

Performance Engine Camshafts

Performance Ring and Pinions

Performance Ignition Parts

Performance Intake Manifold Hardware

Performance Points and Condensers

Performance Lower Control Arm Bushings

Performance Engine Valve Lifters

Performance Tie Rod End Boots

Performance Transmission Shift Kits

Performance Engine Push Rods

Performance Engine Valve Spring Retainer

Performance Torque Converters

Performance Engine Valve Stem Seal Sets

Performance Alternator or Generators

Performance Transmission Rebuild Kits

Essential Performance and Racing Products for 1973 Buick Centurions

from

$170.99

Constructed of thicker than stock steel plate to withstand the stress of high stall speed converters and high RPM engine. Zinc dichromate plated to resist rust and corrosion. Meets SFI specification 29.1 for racing.

Product Features:

Thicker Than Stock Steel Plate
Ring Gear Securely Welded
Dual Bolt Patterns
Zinc-Dichromate Plated To Resist Corrosion
Withstands High Torque and RPM

from

$127.99

What better way to check you oil level by using one of B&M’s transmission fluid dipsticks? The cap screws into the tube and is O-ring sealed, while the base of the tube has a sealing grommet where it goes into the transmission.

Product Features:

Automatic Transmission Dip Stick
Mounts to bellhousing
Sold as a kit
Natural finish
Fits TH350 & TH350C

from

$149.99

Product Features:

Non-Rotator Type
1.550 in. Outer Diameter
.190 Wire Size
Single Coil Spring Type
Set of 16

from

$34.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

from

$34.49

Product Features:

Service Part
Makes Connections Quick And Easy

from

$166.99

The B&M Transpak has all the features in the Shift Improver Kit, plus it provides additional driver manual control. Retain full automatic features and standard shift points with selector in Drive.

Product Features:

Recalibrate Auto. Transmission
Optimum Performance
Select Your App. Mode
Improves Transmission Life
Trans. Removal Not Required
Downshift At Any Speed
Great For Trailer Towing
For Heavy Loads Driving Downhill

from

$32.49

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 195 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$53.99

Knowing your coolant temperature can help to prevent burn injuries. Thermocap Cap, with its built-in calibrated thermometer, indicates the coolant temperature. This is useful information prior to cap removal. Never attempt to remove Thermocap Cap when the coolant temperature is very hot. The escaping hot coolant and steam may burn you. Reclamation valve works great with your coolant recovery system. Your radiator can reclaim coolant from your overflow bottle. Wide 30 degree to 270 degree F temperature range. Calibrated in centigrade and Fahrenheit. Color-coded temperature ranges.

Product Features:

Indicates Coolant Temperature
Helps to Prevent Injuries from coolant or steam burns
Integrated Coolant Reclamation Valve
Improves Underhood Appearance
Fahrenheit and centigrade readings
Various valve pressures available

from

$511.99

A B&M transmission in a box! Transform your automatic transmission into a full-tilt B&M performer! This is our ultimate transmission kit – it comes complete with full instructions on how to assemble your transmission to B&M specifications.

Product Features:

High Perf. Friction Materials
Complete Overhaul Gasket Set
Modification Components
Replacement Valves
Replacement Springs
Drain Plug Kit Included

from

$13.29

Made of superior Hyper-Flex material. Saves replacing again and again, lasting 3 to 10 times longer. Assemble to chassis the same way as OEM isolators and do not adversely change ride characteristics.

Product Features:

Made of Superior Hyper-Flex+ Material
Lasts from 3 to 10 Times Longer
Assemble to Chassis Same Way as OEM
Maintains Factory Ride Characteristics
Simple Way to Increase Vehicle Height

from

$19.29

Distributor Condenser

from

$26.99

Spectre’s Oldsmobile V8 water neck fits Oldsmobile 330, 350, 425 and 455 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck has an additional by-pass hose connection and includes the bolts.

Product Features:

Fits Oldsmobile 330, 350, 425 and 455 engines
Chrome plated
Bolts included
Designed for OEM fit
Easy to install
O-ring/gasket not included

from

$767.99

Matched assembly for maximum reliability. An excellent choice for high performance street applications.

Product Features:

Built As Matched Assembly
Exceptional Performance
Exceptional Durability
Long Term Dependability
Designed for Street And Street Strip Applications

from

$665.99

MSD Pro-Billet Distributors are the finest performance and racing distributors available. Every feature has been engineered to endure the rigors of high performance and racing engines. Whether cruising the streets or racing stock cars, dragsters, boats or trucks, MSD has a distributor for it. MSD uses state-of-the-art, Computer Numerical Controlled (CNC) mills and lathes to machine each housing. After a long series of precise cuts and movements, the billet is formed into a flawless distributor housing that is accurate to within 0.001″. The flex-free housings are lightweight, have no porosity or weak areas and look great on polished, show quality engines.

Product Features:

CNC machined billet aluminum housing and billet aluminum base
Must Be Used w/An MSD Ignition Control
Supplied w/HEI style distributor cap/rotor (accepts Cap-A-Dapts)
Mech. advance assem. can be locked out for crank trigger systems
Advance plate and weights are fine blanked from chrome moly steel
QPQ coated for friction reduction
QPQ coated polished steel shaft; guided by sealed ball bearings
Easy-to-adjust mech. advance w/supplied springs and stop bushings

from

$819.99

The off-road truck avenger is designed specifically for off-road applications. The unique fuel metering block eliminates fuel spillover through the boosters at extreme angles allowing for 40 degree climbing, 30 degree side hill maneuvers and nose-down descents to avoid hesitations, stalling and flooding typically associated with carbs in an off road environment. The 470 CFM off-road truck avenger is the perfect carburetor for 4 cylinder, V-6, and inline 6 cylinder engines. Viton(R) is a registered trademark of DuPont Performance Elastomers.

Product Features:

Gold Dichromate Finish For Extreme Off Road Environments
Single Feed Fuel Inlet For Ease Of Installation
Optimized Off-Road Calibration That Works Out-Of-The-Box
Factory Preset Electric Choke For Easy Startups
Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
One Piece Off-Road Vent Tube Eliminates Fuel Spillover
Metering Block For Flood Free Op. 40 deg. Climb/30 deg. Side Hill
Limited Lifetime Warranty Defects In Material/Workmanship

from

$799.99

The B&M Racing Street Bandit Pistol-grip shifter is perfect for the person looking for a gated performance shifter in a compact good looking package which can be mounted in door cars. The Street Bandit features replaceable 2, 3 or 4 speed forward pattern gate plates along with a 3 speed reverse pattern gate plate, all guaranteeing you won’t miss a shift. Other features include a back-up light switch, neutral safety switch, brushed aluminum cover, CNC aluminum Magnum Grip shift handle, a 5ft Super Duty cable, all brackets, levers and instructions for an easy installation. Be sure to check out all our optional side grip plates including real Rosewood engraved with the B&M logo part #81086, CNC billet aluminum side plates with 12 volt micro-switch #81060, 81063, 81078 and coming soon optional colored side plates to customize the look of the shifter. Also see optional floor mounting bracket #80884

Product Features:

Ideal For High-Tech Pro-Street
Ideal For High-Tech Street Rods
Narrow Styled Aluminum Housing
Includes Neutral Safety Switch
Includes Backup Light Switch
Includes Billet Aluminum Knob
Can Be Used w/Reverse Pattern Valve Body

from

$369.99

RngPnn

from

$26.99

Hold your alternator securely in place with Mr. Gasket chrome alternator bracket. Chrome plated heavy gauge steel for long lasting good looks. Must be used with #9852.

Product Features:

Chrome Plated Steel
F-Style
Heavy Gauge Steel Construction
Fits Small Block Chevy 265-400 CID
Must Be Used With Part 9852

from

$33.99

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Product Features:

Work with .530″ guides and 3/8″ valve stem diameter
Valve stem oil seals keep unwanted oil from entering the combustion chamber
Several different types of valve seals are offered

from

$19.99

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. Designed to operate with all synthetic, conventional, and blended motor oils, K&N’s pleated synthetic-blend filtration media helps to shield your engine from contaminants and ensure a consistent flow of oil. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers, and is protected by the K&N 1-Year Limited Warranty.

Product Features:

Designed to allow high flow rates and a consistent flow of oil to your engine
Pleated synthetic-blend filtration media removes most harmful contaminants
Fast and easy Wrench-Off removal using the welded one-inch hex nut
High capacity to withstand the service intervals recommended by vehicle manufacturers
Heavy-duty canister for outstanding durability
Laboratory tested to ensure excellent capacity, efficiency, and mechanical strength
Designed to operate with all synthetic, conventional, and blended motor oils
1-Year Limited Warranty

from

$25.99

Spectre’s Chevy short block timing chain cover kit is designed to protect engine components like timing gears and the timing chain. This kit features a triple chrome plated steel construction and includes a pre-installed seal, base gasket, (10) 12-point screws and a 12 point socket. This timing cover kit is engineered for optimum fit and function and it is designed to fit Chevy 265-400 short block engines.

Product Features:

Fits Small Black Chevrolet 265-400 Engines
Triple chrome plated
Steel construction
Includes pre-installed seal, gasket, (10) 12-point bolts and a 12 point socket
OEM fit & function
Spectre timing tab 4236 or 4237 is recommended

from

$318.99

The Mr. Gasket chrome alternator is a high-performance, remanufactured solution designed to exceed original equipment specifications, ensuring maximum dependability for your vehicle. With an 80-amp output and a sleek chrome-plated finish, this GM 10SI style alternator is both functional and visually appealing. It fits most 1973-1983 GM vehicles, making it a versatile replacement option. The alternator features a 6.6″ bolt spacing, an internal regulator for efficient voltage control, and a 1-groove V-belt pulley included for easy installation. Operating at 12 volts, it can be used as a direct OE replacement or as a 1-wire alternator, offering flexibility to suit your needs. Built for durability and reliability, this alternator is an excellent choice for restoring or upgrading your vehicle’s electrical system.

Product Features:

Fits Most 1973-1983 GM Vehicles
Bolt Spacing 6.6″
80 Amps
GM 10SI Style Alternator
Chrome Plated Finish
1-Groove V-belt pulley – included
Internal Regulator

from

$81.99

Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermoconductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually.brbrGasket Bore 4.130 inch, Compressed thickness 0.055 inch

Product Features:

Five layer (graphite core/perforated steel outer layers) composite construction
Graphite core is excellent transfering heat away from hot spots in head preventing gasket burn-out.
Provides excellent stability, compressibility and high temperature endurance
Coated with high temperature silicone to ensure sealing of engine fluids
Will not brinell (indent) aluminum cylinder heads
For high performance street, drag race and oval track use
Compatible w/High Octane Fuel
Compatible With Exotic Fuel

from

$31.99

This Spectre OEM replacement air filter is an easy to install performance option for multiple Buick, Cadillac, Chevy, GM, Mercedes, Oldsmobile and Pontiac applications that use a 14 inch by 3 inch round air filter. With its performance synthetic air filter media, this air filter has been designed to add horsepower and quicker acceleration by allowing more air flow into your engine than ordinary paper filters. This air filter’s sealing edge was engineered to insure a proper air cleaner housing seal for great engine protection.

Product Features:

Replacement for 14 inch by 3 inch round air filter
Fits perfectly in your vehicle’s air box as a replacement for your factory air filter
Engineered for increased flow and greater performance
Fits select Buick, Cadillac, Chevy, GM, Mercedes, Oldsmobile and Pontiac models
Factory pre-oiled and ready to use
Simple installation

from

$116.99

Put an end to high maintenance points ignition systems by installing an ACCEL points eliminator ignition conversion kit. By utilizing specialized electronic circuitry and an infrared signal, ignition timing is stable from 1 to 10,000 RPM. More accurate ignition timing than any other type of system. Improves performance and fuel efficiency. Easy to install with simple hand tools. Reduced maintenance-eliminates changing points forever. Latest thermal clad based surface mount construction for maximum dependability and long life. Available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

More Accurate Ignition Timing
Improves Performance And Fuel Economy
Provides More Accurate Ignition Timing
Easy To Install w/Hand Tools
Reduced Maintenance
Thermal Clad Based Surface Mount Construction
Utilizes Specialized Electronic Circuitry
Ignition Timing Is Stable From 1 To 10000rpm

from

$179.99

Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

Easy Installation
Improved Fuel Economy
Reduced Maintenance
Accurate Timing
Improved Performance
Provides A Simple Conversion
No Moving Parts To Wear Out

from

$226.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$226.99

HYDRAULIC – Magnum: Great for street machines. Needs 2200+ stall, headers and gears. Rough idle.

Product Features:

HYDRAULIC – Magnum: Great for street machines. Needs 2200+ stall, headers and gears. Rough idle.
280/280 Advertised Duration, 230/230 Duration @ .050″, .480″/.480″ Lift, 110 Lobe Separation
Valve spring upgrade required

Upgrade your 1973 Buick Centurion with Top-Quality Performance and Racing Products

When it comes to maintaining or upgrading your 1973 Buick Centurion, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Buick or enhancing its overall performance, Performance and Racing Products are key to keeping your Centurion functioning at its best. At Advance Auto Parts, we offer a wide selection of 141 Performance and Racing Products for the 1973 Buick Centurion, designed to meet your needs without breaking the bank. From Performance Oil Filter replacements to Performance Air Filters upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1973 Buick Centurion at great prices. Our Performance and Racing Products inventory for this model ranges from just $5.99 to $1,201.99, with an average price of $296.40. Our 141 Performance and Racing Products in stock come from 16 trusted brands, so you’re sure to find the right part for your 1973 Buick Centurion without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1973 Buick Centurion, we stock popular OEM and aftermarket Performance and Racing Products from top names like Holley, B & M, Competition Cams, and more. Holley Performance and Racing Products start at just $509.99 and boast an impressive 4.2 stars average rating from customers. B & M and Competition Cams also bring quality to the table, with Performance and Racing Products available starting at $33.99, and at an average 4.1 stars rating. With 958 customer reviews and counting, our 1973 Buick Centurion Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Fluids and Chemicals and more to make sure your 1973 Buick Centurion is always ready to roll. We’re committed to providing you with everything you need to keep your Centurion in top shape, all in one place. Start shopping confidently below for your 1973 Buick Centurion!

Best-Selling Performance Oil Filters for 1973 Buick Centurions

Enhance the driving experience in your Buick with 1 quality Performance Oil Filter components, starting at $19.99.

show more show less

from

$19.99

Designed to allow high flow rates and a consistent flow of oil to your engine
Pleated synthetic-blend filtration media removes most harmful contaminants
Fast and easy Wrench-Off removal using the welded one-inch hex nut
High capacity to withstand the service intervals recommended by vehicle manufacturers
Heavy-duty canister for outstanding durability
Laboratory tested to ensure excellent capacity, efficiency, and mechanical strength
Designed to operate with all synthetic, conventional, and blended motor oils
1-Year Limited Warranty

Most Popular 1973 Buick Centurion Performance Air Filters

Customize your Buick with 2 Performance Air Filters products like Performance Air Filters, all priced under $83.99.

show more show less

from

$83.99

K&N washable, reusable High-Flow Air Filters feature a state-of-the-art design of layered, oiled cotton media engineered to improve airflow and capture contaminants, and are designed to provide an increase in horsepower. Each performance air filter is reusable, engineered to last for the entire lifespan of your vehicle, and backed by K&N’s No-Hassle Lifetime Limited Warranty. K&N drop-in replacement filters are designed to install easily into your factory air box. Upgrade today and start enjoying superior airflow and superior performance from K&N’s most popular product!

Product Features:

REUSABLE K&N FILTER SAVES YOU MONEY: A K&N washable, reusable air filter will save you up to $125 vs. purchasing multiple disposable filters (compared to MSRP in USD of corresponding OE filters for 200,000 miles of highway driving)
CLEAN ONCE EVERY 5 YEARS: Engine air filter only needs cleaning every 75,000 miles under normal highway driving conditions (5 years based on the average miles driven per year of 15,000 miles)
RUGGED CONSTRUCTION: K&N Air Filters are manufactured with durable, premium materials and state-of-the-art construction methods to last a lifetime
REDUCES WASTE: Over 200 million disposable air filters and their packaging waste wind up in landfills each year- reusable filters help reduce waste in our landfills
ENGINEERED POWER: State-of-the-art air filter media is designed to increase horsepower and acceleration as well as improve overall engine performance
EASY INSTALLATION: K&N Air Filters are pre-oiled and ready to drop into your factory air box- they are one of the easiest and most cost-effective vehicle upgrades for quick performance gains
4 LAYERS OF PROTECTION: Multiple layers of premium cotton gauze treated with a specially-designed tacking agent work together to create an intricate mesh of engine filter media that is designed to block and trap harmful contaminants
ULTIMATE LONGEVITY: No-hassle lifetime limited warranty on stock replacement K&N air filters- limitations apply

from

$31.99

Replacement for 14 inch by 3 inch round air filter
Fits perfectly in your vehicle’s air box as a replacement for your factory air filter
Engineered for increased flow and greater performance
Fits select Buick, Cadillac, Chevy, GM, Mercedes, Oldsmobile and Pontiac models
Factory pre-oiled and ready to use
Simple installation

Top Picks for 1973 Buick Centurion Performance Fuel Systems

Upgrade Buick Centurions with top-quality Performance Fuel Systems parts, including 8 OEM and aftermarket selections for your 1973 model.

show more show less

from

$14.49

This is what you need when changing your manual fuel pump to electric. It blocks the hole that remains when you remove the mechanical fuel pump from the engine to keep the oil inside. This plate is precision machined and is chrome plated.

Product Features:

Chrome Plated Steel
Comes With Gasket

from

$509.99

Holley’s new 0-80457SA is constructed from aluminum which compared to its zinc counterpart equates to a weight savings of 40%! Holley’s aluminum 0-80457SA will hold its shine longer and also can be hand polished for a custom look! Its 600 CFM of airflow,

Product Features:

Vibratory Polished For Good Looks

from

$394.99

The Edelbrock 1405 Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1405 Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Manual Choke
4 Barrel Count
Square Bore
Smooth Secondary Transition
Both Timed and Full Vacuum Ports
Includes PCV Outlet

from

$716.99

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

Vibratory Polished For Good Looks
Optimized Street Calibration That Works Out Of The Box
Factory Preset Electric Choke For Easy Startups
Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
No Unnecessary Trips Back To The Parts Store
Limited Lifetime Warranty
100% Wet Flow Tested By Holley Technicians
Arrives Ready To Run

from

$699.99

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

Vibratory Polished For Good Looks
Optimized Street Calibration That Works Out Of The Box
Factory Preset Electric Choke For Easy Startups
Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
No Unnecessary Trips Back To The Parts Store
Limited Lifetime Warranty
100% Wet Flow Tested By Holley Technicians
Arrives Ready To Run

from

$13.99

Spectre’s triple chrome plated Fuel Pump Block Off Plate was designed for small block Chevrolet engines. Engineered for optimum fit and function, this kit includes a block off plate gasket and chrome mounting bolts with washers.

Product Features:

Necessary if switching to electric fuel pump
Includes block off plate gasket
Includes chrome mounting bolts with washers
Triple chrome plated

from

$819.99

Gold Dichromate Finish For Extreme Off Road Environments
Single Feed Fuel Inlet For Ease Of Installation
Optimized Off-Road Calibration That Works Out-Of-The-Box
Factory Preset Electric Choke For Easy Startups
Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
One Piece Off-Road Vent Tube Eliminates Fuel Spillover
Metering Block For Flood Free Op. 40 deg. Climb/30 deg. Side Hill
Limited Lifetime Warranty Defects In Material/Workmanship

from

$523.99

The Edelbrock 1400 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characterist

Product Features:

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Electric Choke
4 Barrel Count
Square Bore
Electric Choke Installed from Factory
Smooth Secondary Transition
Includes Only Timed Vacuum Port
Includes EGR ; Fuel Vapor Outlet

In-Demand Performance Exhaust Products for 1973 Buick Centurions

Select from 4 premium Performance Exhaust Products parts for your 1973 Buick Centurion, with prices ranging from $26.99 to $41.99.

show more show less

from

$26.99

Hold your alternator securely in place with Mr. Gasket chrome alternator bracket. Chrome plated heavy gauge steel for long lasting good looks. Must be used with #9852.

Product Features:

Chrome Plated Steel
F-Style
Heavy Gauge Steel Construction
Fits Small Block Chevy 265-400 CID
Must Be Used With Part 9852

from

$34.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

from

$41.99

Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head.

Product Features:

Withstands Intense Exhaust Heat
Graphite-Impregnated Facing
Superior Tensile Strength
Resists Deteriorating
Anti-stick Properties
Resists Deteriorating
Anti-Stick Properties
Easy Removal For Disassembly

from

$34.99

Edelbrock part No. 7247 Exhaust Gaskets are designed for 1967-76 Buick 400-455 V8 engines. These Exhaust Gaskets are made of EnCore HTX-900

Most Sold 1973 Buick Centurion Performance Engines

Explore our best-selling Buick parts for the 1973 Centurion among 73 OEM and aftermarket options starting from $10.99.

show more show less

from

$33.99

Work with .530″ guides and 3/8″ valve stem diameter
Valve stem oil seals keep unwanted oil from entering the combustion chamber
Several different types of valve seals are offered

from

$12.99

Spectre’s Chevrolet V8 water neck fits 1966 – 1995 Chevy V8 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes bolts.

Product Features:

Fits 1966 – 1995 Chevy V8 engines
Includes bolts
Chrome plated
Designed for OEM fit
Easy to install
O-ring/gasket not included

from

$562.99

Torque Converter – Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New allow steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required.

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer
Washer Between Turbine and Cover

from

$914.99

SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Big Mutha’ Thumpr: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.

Product Features:

Cam and lifter kit for Small Block Chevy engines
CL-Kit includes cam, lifters, assembly lube, instructions and decals
HYDRAULIC – Big Mutha’ Thumpr: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.
295/313 Advertised Duration, 243/257 Duration @ .050″, .500″/.486″ Lift, 107 Lobe Separation
Valve spring upgrade required

from

$898.99

SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – High Energy: Good street performance with stock converter, choppy idle. OR High Energy Marine: Biggest cam for inboard/outboard. Good for ski, economy and light performance.

Product Features:

Cam and lifter kit for Small Block Chevy engines
CL-Kit includes cam, lifters, assembly lube, instructions and decals
HYDRAULIC – High Energy: Good street performance with stock converter, choppy idle. OR High Energy Marine: Biggest cam for inboard/outboard. Good for ski, economy and light performance.
268/268 Advertised Duration, 218/218 Duration @ .050″, .454″/.454″ Lift, 110 Lobe Separation
Valve spring upgrade required

from

$10.99

Spectre’s Intake Bolt and Washer Set is engineered to provide premium quality hardware for Chevrolet 265-400 and Chrysler 273-440 small block engines. Measuring 3/8 inch-16 by 1 inch, these grade 5 bolts feature a corrosion resistant zinc-plated finish and hex heads to ensure easy installation. This kit includes 12 bolts and washers.

Product Features:

Designed for Chevrolet 265-400 and Chrysler 273-440 small block engines
3/8 inch-16 by 1 inch bolts
Kit includes 12 bolts and washers
Manufactured from high quality steel
Bolts feature hex heads

from

$32.49

Opens At 195 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$32.49

Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:

Complete with o-rings and mounting bolts
Features an o-ring style seal to prevent water leaks
Chrome plated
1/2″ NPT port can be used for various coolant temp related sensors or switches

from

$26.99

Fits Oldsmobile 330, 350, 425 and 455 engines
Chrome plated
Bolts included
Designed for OEM fit
Easy to install
O-ring/gasket not included

from

$223.99

Work with .530″ guides and 11/32″ valve stem diameter
Valve stem oil seals keep unwanted oil from entering the combustion chamber
Several different types of valve seals are offered

from

$89.99

Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermoconductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually.brbrGasket Bore 4.230 inch, Compressed thickness 0.038 inch

Product Features:

Five layer (graphite core/perforated steel outer layers) composite construction
Graphite core has excellent thermo-conductivity-transfers heat away from hot spots in head preventing gasket burn-out
Provides excellent stability, compressibility and high temperature endurance
Coated with high temperature silicone to ensure sealing of engine fluids
Will not brinell (indent) aluminum cylinder heads
For high performance street, drag race and oval track use
Compatible w/High Octane Fuel
Compatible With Exotic Fuel

from

$37.99

The Edelbrock valve cover gaskets #7546?provide excellent sealing integrity and conformability for easy installation. The multi-layer construction has two highly compressible, high rubber content, fiber-reinforced outside layers which are chemically bonde

Product Features:

0.1875 in. Thickness
Core-Reinforced-Composite Material
For Buick 400-455
Set of 2
Made In The USA

from

$337.99

Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer

from

$226.99

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$258.99

HYDRAULIC – Xtreme Energy: Very strong mid-range torque and throttle response, 2200+ stall.

Product Features:

HYDRAULIC – Xtreme Energy: Very strong mid-range torque and throttle response, 2200+ stall.
274/286 Advertised Duration, 230/236 Duration @ .050″, .490″/.490″ Lift, 110 Lobe Separation
Valve spring upgrade required
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$81.99

Five layer (graphite core/perforated steel outer layers) composite construction
Graphite core is excellent transfering heat away from hot spots in head preventing gasket burn-out.
Provides excellent stability, compressibility and high temperature endurance
Coated with high temperature silicone to ensure sealing of engine fluids
Will not brinell (indent) aluminum cylinder heads
For high performance street, drag race and oval track use
Compatible w/High Octane Fuel
Compatible With Exotic Fuel

from

$32.99

Edelbrock part #7246 Intake Gaskets for 1967-1976 400-455 Buick allow for optimum flow and performance. Any gasket can create a seal, but a good gasket can do it with less clamping force, and for a longer period of time. The new MP-2N Micropore technology

Product Features:

1.15″x2.38″
Features Embossed Silicone Bead Around The Intake Ports & Water Openings
.032″ Thick
Two Piece Configuration
End Seals Not Included

from

$44.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

from

$471.99

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

Product Features:

Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
Best with aftermarket converters and more rear gear.
Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.

from

$251.99

HYDRAULIC – Xtreme Energy: Great for street machines, largest cam for stock converter, better with 2000 stall.

Product Features:

HYDRAULIC – Xtreme Energy: Great for street machines, largest cam for stock converter, better with 2000 stall.
268/280 Advertised Duration, 224/230 Duration @ .050″, .477″/.480″ Lift, 110 Lobe Separation
Valve spring upgrade required
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$1201.99

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.

Product Features:

Good blend of efficiency and performance.
Perfect choice for performance street rebuilds.
Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

from

$1152.99

Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
Best with aftermarket converters and more rear gear.
Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.

from

$972.99

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine
Dual Pattern Drive Lugs
New Turbine Hub
New Springs/Rollers In Stator

from

$963.99

SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Mutha’ Thumpr: High performance street/strip, needs 9:1 compression, 2500+ stall, intake, gears and headers, rough idle.

Product Features:

Cam and lifter kit for Small Block Chevy engines
CL-Kit includes cam, lifters, assembly lube, instructions and decals
HYDRAULIC – Mutha’ Thumpr: High performance street/strip, needs 9:1 compression, 2500+ stall, intake, gears and headers, rough idle.
287/305 Advertised Duration, 235/249 Duration @ .050″, .489″/.476″ Lift, 107 Lobe Separation
Valve spring upgrade required

Top-Rated Performance and Racing Products Brands For Your 1973 Buick Centurion

Shop for the best-rated brands offering Performance and Racing Products and other products for your 1973 Buick Centurions. Below you’ll find some of our best rated Performance and Racing Products from Holley, B & M, and Competition Cams, and more. Performance and Racing Products from these brands that fit a 1973 Centurion start at just $33.99 and are rated as high as 4.2 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.

Popular Holley 1973 Buick Centurion Performance and Racing Products

When it comes to maintaining or upgrading your 1973 Buick Centurion, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. Holley ticks all of those boxes. We offer a wide selection of Holley Performance and Racing Products, specifically designed for the 1973 Buick Centurion. With over 3 Holley brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $509.99, with an average price of just $642.32. Plus, with over 53 customer reviews and an average rating of 4.2 stars, you can trust that our Holley Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from $509.99

(45)

Street Carburetor: 600 CFM, Electric Choke, 4 Barrel, Square Bore, Single Inlet, Shiny

“very easy to install…replaced older carb this one is fresh and runs smooth … needed to do minor ajustment .. but nothing anyone couldn’t do …”

from $699.99

(6)

Street Carburetor: 670 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny

“great carb”

from $716.99

(2)

Prem Street Carbs (Avengers)

“This was the carb that my engine builder suggested.”

Popular B & M 1973 Buick Centurion Performance and Racing Products

B & M auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1973 Buick Centurion owner should feel confident when installing genuine B & M parts in their vehicle. To ensure the best fit and performance for your 1973 Centurion, Advance Auto Parts carries a full inventory of 3 B & M Performance and Racing Products. Plus you will be keeping your Buick in peak condition while saving money because prices on these B & M Performance and Racing Products range from $371.99 to $562.99, plus, with more than 3 customer reviews and an impressive 4.1 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.

from $539.99

(1)

Automatic Shifter – Megashifter – Universal

“its was pretty easy to install if u have any type of knowlegde of cars it should not be difficult at all and the shifting is awesome just be careful w”

from $562.99

(1)

Tork Master 3000

“good parts and very strong”

from $371.99

(1)

Automatic Shifter, Sport Shifter

“This is a sweetly made product with that hotrod look and feel.This shifter was easy to install and a knock out to drive.No down falls as far as I’m aw”

FAQs for 1973 Buick Centurion Performance and Racing Products

Which Performance and Racing Products are best-sellers for 1973 Buick Centurions?

Out of 141 Performance and Racing Products that fit 1973 Buick Centurions, the following parts are the top sellers:

Fuel Pump Block-Off Plate (6121586) – $14.49
Tie Rod Dust Boot (17360821) – $5.99
Tie Rod Dust Boot (17360833) – $5.99

What’s the price range for 1973 Buick Centurion Performance and Racing Products?

Performance and Racing Product prices for the 1973 Buick Centurion start at $5.99 and go up to $1,201.99 for the most premium parts.

What’s the average price of a Performance and Racing Product for a 1973 Buick Centurion?

The average price for Performance and Racing Products for the 1973 Buick Centurion is $296.40. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Performance and Racing Products for other Buick Centurion model years?

Yes, we currently carry Performance and Racing Products for 1 model years of Buick Centurions between 1971 and 1972. Performance and Racing Products are bought most frequently for the following model years: 1972 and 1971.

What are the cheapest Performance and Racing Products for my 1973 Buick Centurion?

The cheapest 1973 Buick Centurion Performance and Racing Products we carry in stock are:

Tie Rod Dust Boot (17360821) – $5.99
Tie Rod Dust Boot (17360833) – $5.99
Tie Rod Dust Boot (22906873) – $6.29
Bolt Kit Intake Hex Head (22905656) – $10.99
11 Steel Retainer for Buick 350-455 with 1.225"-1.250" OD Valve Spring (50289473) – $10.99

What are the top-rated Performance and Racing Products that fit the 1973 Buick Centurion?

Out of 958 reviews by customers, our 1973 Buick Centurion Performance and Racing Products have an average customer rating of . These are some of the highest-rated Performance and Racing Product types for the 1973 Buick Centurion and their top-rated products:

Performance Radiators
- Thermocap Radiator Cap (6900022) – $53.99
Performance Oil Filters
- Thermocap Radiator Cap (6900022) – $53.99
Performance Air Filters
- Thermocap Radiator Cap (6900022) – $53.99

What types of Performance and Racing Products do you sell for my 1973 Buick Centurion?

As of 3/1/26, these are some of the most in-demand types of Performance and Racing Products for a 1973 Buick Centurion:

Can I get help with 1973 Buick Centurion Performance and Racing Product orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Buick Performance and Racing Products and more.

What is your return policy for Buick Centurion Performance and Racing Products?

Advance Auto Parts keeps returns simple. For new Buick Centurion Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1973 Buick Centurion Performance and Racing Products

Hays – Flexplate: Chevy 57-85 (153T) (Part No.10-012)

B & M – Aluminum Braided Dip Stick, Fits TH-350 Transmission (Part No.22165)

Edelbrock – Sure Seat Valve Springs for Chrysler 383-400-413-440 V8 1969-79 (Part No.5792)

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1479)

Mallory – Distributor Wiring Harness (Part No.29349)

B & M – Transpak For 65-87 TH400 Transmission (Part No.20228)

Mr. Gasket – High Performance Thermostat (Part No.4365)

Mr. Gasket – Thermocap Radiator Cap (Part No.2471S)

B & M – Transkit For 65-87 TH400 Transmission (Part No.20229)

Energy Suspension – Coil Spring Isolator Set (Part No.3.6108G)

Mallory – Distributor Condenser (Part No.401)

Spectre – Water Neck; Olds (Part No.4733)

Hays – Power Train (Part No.85-110)

MSD Ignition – Distributor; Buick V8 215-350 Pro-Billet (Part No.8548)

Holley – Off Road Carbs (Part No.0-90670)

B & M – Automatic Shifter, Magnum Grip Street Bandit (Part No.81050)

Richmond Gear – RngPnn (Part No.49-0094-1)

Mr. Gasket – Alternator Bracket (Part No.9850)

Competition Cams – VALVE SEALS, TEFLON 3/8" 1 ST (Part No.505-16)

K&N – Premium Oil Filter: Ideal for Synthetic, Conventional & Blended Oil, Protects Your Engine (Part No.HP-2003)

Spectre – Timing Cover Comp Kit (Part No.42353)

Mr. Gasket – Alternator: Remanufactured, 80 Amps (Part No.5122)

Mr. Gasket – Ultra Seal: Head Gasket (Part No.5799G)

Spectre – Spectre Replacement Air Filter (Part No.HPR0136)

Accel – Points Eliminator Kit (Part No.2010)

Mallory – Unilite Breakerless Ignition Conversion Kit (Part No.503M)

Competition Cams – Xtreme Energy 206/212 Hydraulic Flat Cam (Part No.12-230-2)

Competition Cams – Magnum 224/224 Hydraulic Flat Cam (Part No.12-212-2)

K&N – Premium Oil Filter: Ideal for Synthetic, Conventional & Blended Oil, Protects Your Engine (Part No.HP-2003)

K&N – Engine Air Filter: Washable & Reusable, Engineered to Increase Air Flow and Performance (Part No.E-1650)

Spectre – Spectre Replacement Air Filter (Part No.HPR0136)

Mr. Gasket – Fuel Pump Block-Off Plate (Part No.1515)

Holley – Street Carburetor: 600 CFM, Electric Choke, 4 Barrel, Square Bore, Single Inlet, Shiny (Part No.0-80457S)

Edelbrock – Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1405)

Holley – Prem Street Carbs (Avengers) (Part No.0-80770)

Holley – Street Carburetor: 670 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny (Part No.0-80670)

Spectre – Sbc Blk Off Plate With Bolts (Part No.42463)

Holley – Off Road Carbs (Part No.0-90670)

Edelbrock – Performer 1400 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1400)

Mr. Gasket – Alternator Bracket (Part No.9850)

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1479)

Mr. Gasket – Exhstmnfgsktset (Part No.7529)

Edelbrock – Exhaust Manifold Gasket Set for Buick (Part No.7247)

Competition Cams – VALVE SEALS, TEFLON 3/8" 1 ST (Part No.505-16)

Spectre – Water Neck Chev Late w/Hdr (Part No.42313)

B & M – Tork Master 3000 (Part No.20402)

Competition Cams – Big Mutha’ Thumpr 243/257 Hydraulic Flat Cam/Lifter Kit (Part No.CL12-602-4)

Competition Cams – High Energy/Marine 218/218 Hydraulic Flat Cam/Lifter Kit (Part No.CL12-210-2)

Spectre – Bolt Kit Intake Hex Head (Part No.4652)

Mr. Gasket – High Performance Thermostat (Part No.4365)

Mr. Gasket – Water Neck (Part No.2557)

Spectre – Water Neck; Olds (Part No.4733)

Competition Cams – VALVE SEALS, 11/32" TEFLON 1 ST (Part No.503-16)

Mr. Gasket – Ultra Seal: Head Gasket (Part No.5788G)

Edelbrock – Valve Cover Gasket Set for Buick (Part No.7546)

B & M – Performance Torque Converter for GM TH400, 350, & 375 Transmissions (Part No.20400)

Competition Cams – Xtreme Energy 206/212 Hydraulic Flat Cam (Part No.12-230-2)

Competition Cams – Xtreme Energy 230/236 Hydraulic Flat Cam (Part No.12-246-3)

Mr. Gasket – Ultra Seal: Head Gasket (Part No.5799G)

Edelbrock – Intake Manifold Gasket for 1967-1976 400-455 Buick (Part No.7246)

FEL-PRO Performance – Lower Intake Manifold Gasket Set: 4 Piece Set (Part No.1357)

Competition Cams – Thumpr 226/241 Hydraulic Flat Cam and Lifter Kit (Part No.CL42-600-5)

Competition Cams – Xtreme Energy 224/230 Hydraulic Flat Cam (Part No.12-242-2)

Competition Cams – High Energy 206/206 Hydraulic Flat Cam K-Kit (Part No.K12-205-2)

Competition Cams – Thumpr 227/241 Hydraulic Roller Cam and Lifter Kit (Part No.CL12-600-8)

B & M – Holeshot 3600 (Part No.20425)

Competition Cams – Mutha’ Thumpr 235/249 Hydraulic Flat Cam and Lifter Kit (Part No.CL12-601-4)