1972 Chevrolet C10 Pickup Performance Engines

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 180 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

Chrome water neck with a swivel top allows you to place your coolant hose where you want it to be, not just where the neck allows. Precision die cast for better fitment, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:

• Chrome Plated Aluminum
• O-ring To Prevent Leaks
• Swivels For Hard To Fit Applications
• Comes With Allen Head Bolts

Magnum Pushrods from COMP Cams offer an affordable solution for your .080″ wall chromemoly pushrod needs. Designed to withstand the stresses of a high performance engine, Magnum Pushrods are head-treated for extended durability and have precision formed, reinforced ends. Magnum Pushrods are black-oxide finished with their part number and length laser etched onto the surface for easy identification.

Product Features:

• 3/8″ Diameter, 7.800″ Length
• Magnum Pushrods for Small Block Chevy
• One-piece .080″ wall chromemoly steel tubing
• Heat-treated for extended durability and guide plate compatibility
• Precision formed and reinforced pushrod end

HYDRAULIC – Thumpr: High performance street, stock converter ok, best with 2000+ converter and gears. Choppy/thumping idle.

Product Features:

• HYDRAULIC – Thumpr: High performance street, stock converter ok, best with 2000+ converter and gears. Choppy/thumping idle.
• 279/296 Advertised Duration, 227/241 Duration @ .050″, .498″/.483″ Lift, 107 Lobe Separation
• Valve spring upgrade required

Big Block Chevrolet tubular head dowel, .638/.639 inch o.d. (outer diameter) by 1/2 inch. Packaged two per set. These hard to find dowel pins are precision machined then case hardened for accurate alignment in engine assembly.

Product Features:

• Precision Machined
• Case Hardened
• Give Accurate Alignment
• 2 Per Set

Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.

Product Features:

• Chrome plated
• Grade 8
• 12-point head
• AN washers with no exposed shoulder for a professional appearance

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:

• Repairs That Leaky Rear Main Sail
• Silicone Rubber to Withstand Extreme Engine Oil Temperatures
• Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
• Injection Molded for Precise Fit

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• Complete Kit: Includes Retainers And Locks
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Includes Superior Quality Steel Retainers
• Includes 7 deg. Heat-Treated Valve Stem Locks
• Retainers and Locks Black Oxide Coated
• Non-Rotator Style: Dyno Tested and Street Proven
• Great Match to Edelbrock Camshaft Kit

Product Features:

• Clean Positive Seal
• Embossed Silicone Bead Surrounding The Port
• Matched To Manifolds And Cylinder Heads

Product Features:

• Valve Cover Gasket

Product Features:

• 4.125 in. Cylinder Bore Diameter
• 0.039 in. Thickness
• 8.7cc Volume
• Charcoal Color
• Two Piece Configuration

These Magnum Roller Rocker Arms for Chevy V8 265-400 and V6 200-262 applications are the ultimate street rocker. With a 3/8″ stud diameter and 1.52 ratio, they are designed for serious performance enthusiasts. All Magnum Roller Rocker Arms are constructed

Product Features:

• Roller tip reduces friction while stiff design and superior ratio accuracy yield more effective valve lift
• For applications with less than 350 lbs. of open spring pressure
• Constructed from 8620 chromemoly steel, a superior material that will not flex and ensures maximum lift
• Ultimate street roller rocker arm designed for serious performance enthusiasts

Mr. Gasket Performance Gaskets are a low density material that conforms well to irregular flange surfaces and has very good crush resistance at high flange pressures. Intended for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit.brbrThis Mr. Gasket Performance Timing Cover Gasket Kit includes the timing cover gasket and water pump gasket for your Gen IV or Gen V Chevy 396,402,427,454 Big Block.

Product Features:

• Includes Timing Cover Gasket and Water Pump Gaskets
• Won’t shrink or stick and provide an airtight leak proof seal
• Engineered specifically for big block Chevys and ideal for high performance and race applications
• Ensures optimum torque retention ideal crush resistance and excellent sheer strength using minimal clamp force yet still releases easily

Product Features:

• Timing Chain Only

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
• With steel core to provide ultimate excellent blowout resistance.
• Not intended for use in emission controlled vehicles.

Valve spring retainers for use OE cast iron heads. Superior quality heat-treated steel. Machined for strength with black oxide finish. Finish ensures rust and corrosion protection.

Product Features:

• Valve Spring Retainers for Use OE Cast Iron Heads
• Superior Quality Heat-Treated Steel
• Machined for Strength with Black Oxide Finish
• Finish Ensures Rust and Corrosion Protection

Product Features:

• Use W/ Valve Springs Part #5703, 5794
• Set of 16
• 1.50 in. Outside Diameter
• Steel Material
• Black Oxide Finish

Product Features:

• Made of aluminum with a natural finish
• 100cc chambers with 290cc intake ports
• 2.19 in. intake and 1.88 in. exhaust valves
• Bare Cylinder Head
• Standard intake and exhaust port location

Product Features:

• 50-State Street Legal Aluminum Cylinder Head
• Out-of-the-Box Bolt-On Performance
• 64cc Combustion Chambers Improve Performance
• Retain Stock Compression Ratio

BIG BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Big Mutha’ Thumpr: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.

Product Features:

• Cam and lifter kit for Big Block Chevy engines
• CL-Kit includes cam, lifters, assembly lube, instructions and decals
• HYDRAULIC – Big Mutha’ Thumpr: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.
• 295/312 Advertised Duration, 243/257 Duration @ .050″, .522″/.507″ Lift, 107 Lobe Separation
• Valve spring upgrade required

Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

Product Features:

• 8″ diameter
• 1970-73, 396-427-454 cu. in.
• 1967-69, 302 cu. in.
• 1965-68, 327 cu. in. hi-performance
• 1970-76, 400 cu. in.
• 1970-73, 350 cu. in.

Product Features:

• Maximizes Performance with Edelbrock Carburetors
• Runners Tuned to Match Square Bore Carburetor
• Maximizes Peak Torque Around 3500 RPM
• Excellent Throttle Response and Mid-Range Power
• For Idle to 5500 RPM Street-Driven Performance
• Dual-Plane Low-Rise Intake w/180 deg. Firing Order
• Prod. +5 HP and +9 ft/lbs. of Torque Over PN[2101]

For 3500 to 7500 PRM. Use where low-end torque is not a prime factor. Great for engines with slightly modified heads. HEI ignition will not clear manifold. Street machines, street rods, pro-street and marine.

Product Features:

• For 3500 to 7500 RPM
• Use Where Low-End Torque is Not a Prime Factor
• Great For Engines w/Slightly Modified Heads
• Top Has Vacuum Outlet for Power Brakes
• Will Accept Forward and Sideways Mounted Carbs
• Carburetor Center-to-Center Dimensions 9.38 in
• HEI Ignition Will Not Clear Manifold
• Street Machines; Street Rods; Pro-Street; Marine

Product Features:

• Designed For Today’s Larger Cubic Inch Big Block
• Perfect For Hard Core Drag Racers
• Permanent Mold Casting Process
• For Lighter And More Consistent Castings
• Dyno Proven To Make 17hp More Than Competitors

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:

• Maximum Cooling for Street and Racing Engines
• Internal Passages Are Balanced for Maximum Flow
• Impeller is Larger than Others For Max Pressure
• Impeller Vanes Dramatically Increase Flow Rates
• Equal Distribution to Both Sides of Block
• Only Flows in One-Direction for Optimum Efficiency

Product Features:

• Standard Impeller Rotation
• 0.625 in. Pilot Shaft
• 0.750 in. Ball/Ball Bearing
• 7.3125 in. Block To Hub Height
• Satin Finish

Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:

• Twisted Snout Water Pump Design For Updated Style
• Street Performance
• Heavy Duty Shaft w/5/8 in. Pilot
• Six-Blade Stamped Steel
• Anti-Cavitation Impeller
• 100 Percent Leak Tested