1971 Pontiac LeMans Differentials

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Design type: spring loaded; multi-lip
• Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
• Resistance to EP lubricants
• Low swell in hydrocarbon fluids
• Delivers quality and reliable performance for every type of repair

Product Features:

• GM10 BOLT 8.5″ 28 SPL INTERNAL KIT (OPEN)

3/8″ ring gear bolt washer for GM 12 bolt car & truck, 8.2 BOP & more.

Product Features:

• Ring gear bolt washer for GM 12 bolt car and truck, 1955-1964 passenger car, 1963-1979 Corvette and 8.2″ Buick, Oldsmobile and Pontiac

Yukon Gear & Axle offers a full line of top quality differential tools to save time and money.

Product Features:

• Fits M802011 race
• All-steel construction
• For accurate installation of bearing races

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND.

8.5″ GM EXTRA HD standard Open case (uses larger bearings).

Product Features:

• Standard open carrier case
• Fits GM 8.5″ with 28 or 30 spline axles
• 2.73 and up ratio only
• Does not include spider gears
• Has larger carrier carrier bearing journals for high strength

Spartan spring & pin kit, fits smaller designs.

Product Features:

• Replacement spring and pin kit for Spartan Locker
• Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
• Includes 4 springs and 4 alignment pins

Value-priced bearing meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Mr. Gasket Axle Housing/Differential Cover or Rear End Gaskets are manufactured from a .047 inch thick cellulose/nitrile composite gasket material for excellent sealing and durability. They are precision die-cut for an excellent fit. Fits 1964-1970 Chevrolet 8.2 inch 10 bolt & 1970-1981 GM 8.5 inch ring gear

Product Features:

• .047″ thick cellulose/nitrile composite gasket material
• Precision die cut
• Reusable

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Pinion nut for GM 7.2″, 7.5″, 7.625″, 8.0″, 8.25″ IFS, 8.5″, 8.6″, 9.25″ IFS and 9.5″
• 7/8″ x 14 thread
• 1 1/4″ socket

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND.

Product Features:

• For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond.
• The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
• Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
• Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by limited warranty.
• Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

Yukon Pinion Installation Kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings and races can be reused. This kit features Timken bearings and races along with high-quality seals and small parts. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your gear set.

Product Features:

• Fits 8.2″ Buick, Oldsmobile and Pontiac
• Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

We develop and produce high-quality roller bearings, spherical bearings, and plain bearings worldwide for a wide range of applications.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects. This unit has larger bearing journals for added strength & uses heavy-duty carrier bearings & races.

Product Features:

• Fits GM 8.5″ with 28 spline axles
• 2.73 ratio and up only
• 4-spring, clutch style positraction
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Spider gear kit
• Fits GM 8.5″ 28 spline open differential
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits 8.5″ Oldsmobile with 28 spline axles
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin shaft for GM 8.5″ and 8.6″
• Fits standard open differentials only
• 0.795″ diameter

Yukon shim kits are precision machined and tailored for each individual application to ensure you have the right shims for every set up.

Product Features:

• Super carrier shim kit for Ford 7.5″, GM 7.5″, 7.625″, 7.6″ IFS, 7.6″ IRS, 7.75″, 8.2″, 8.2″ Buick, Oldsmobile and Pontiac and GM 8.5″ front and rear
• Interlocking design makes installation much easier

Yukon Gear and Axle manufactures a complete line of general replacement and performance series of pinion yokes for many street, racing, and heavy-duty off-road applications.

Product Features:

• Fits GM 8.5″ and 8.6″
• 30 spline
• Mechanics 3R u-joint size
• 2.556″ snap ring span
• 1.125″ cap diameter
• Inside snap ring design
• Strap style

The Motive Gear replacement axle shaft offers an OE-quality axle shaft at a fraction of the OE cost. Manufactured from 1541H material on high-tolerance CNC equipment, this axle shaft is designed to provide a perfect fit every time.

Product Features:

• AXLE SHAFT 8.2″ 28 SPL. 30 1/8″ L&R

Ring gear bolt for GM 12 bolt car & truck, 8.2″, 8.2″ for Buick/Olds/Pontiac, 63-79 Corvette & 55-62 GM Car & Truck. 3/8″ x 24.

Product Features:

• Ring gear bolt for GM 12 bolt passenger car and truck, 1955-1964 passenger car and truck, GM 8.2″, 8.2″ Buick, Oldsmobile and Pontiac and 1963-1979 Corvette
• 3/8″ x 24 thread

This Yukon Gear & Axle clutch kit is a direct replacement for the popular Yukon Dura Grip positraction unit.

Product Features:

• Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ differentials
• Dura Grip composite replacement clutches
• 14 piece kit
• Composite clutches

Product Features:

• Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.
• Dana engineering-approved for fit, form and function
• Meets or exceeds OE specifications

Product Features:

• GM 10BL 7.5 &7.625 R/P 3.42X* MGP

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Pinion gear thrust washer for GM 8.5″ and 8.6″
• Fits standard open differentials only
• 0.795″ I.D.

Union 76 gear oil is a conventional non-synthetic 80W90 formulation designed for all types of differentials.

Product Features:

• Includes three quarts of conventional oil

For vehicles that are driven daily, the Power Trax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Power Trax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Power Trax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Power Trax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds.

Product Features:

• The Power Trax Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Power Trax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.
• Power Trax lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.
• Power Trax offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.
• Power Trax ia an Extreme Traction System

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on