1971 Dodge Challenger Differentials

Find your specific 1971 Dodge Challenger original or aftermarket Differentials below. Order your parts online and have delivered to your home or pick up in-store at Advance Auto.

Essential 1971 Dodge Challenger Differentials

from

$209.99

Product Features:

Fits Chrysler 9.25″ rear with open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$186.99

Product Features:

FULL SPOOL DANA 60 35 SPLINE 4.10 & DOWN

from

$26.99

Product Features:

Pinion nut
Fits Chrysler 7.25″, 8.0″, 8.25″, 9.25″ and 8.75″ with 29 spline pinion

from

$37.99

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

from

$15.99

Crush Sleeve for Chrysler 8″ & 9.25″ rear. Approx 0.630″ long.

Product Features:

Crush sleeve for Chrysler 8.0″ IFS and 9.25″ rear, also Ford 9″ with aftermarket Daytona pinion support
0.630″ tall

from

$8.29

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$292.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Chrysler 8.75″ ’41’ case
Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

from

$684.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

from

$84.99

Standard Open notched cross pin shaft for 9.25″ Chrysler.

Product Features:

Cross pin shaft
Fits Chrysler 9.25″
Standard open carrier only
Notched

from

$142.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

Fits Chrysler 8.75″ ’42’ case
Included are a pinion seal, pinion nut, completete shim kit, marking compound and brush.

from

$9.99

Ring gear bolt for Chrysler 9.25″ rear, 7/16″ x 18.

Product Features:

Ring gear bolt for Chrysler 9.25″ rear

from

$10.79

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$96.99

Product Features:

BEARING KIT 8.75 CHRY 1.875 489 CST OPEN/AUBURN/TRUETRAC/DET.LOCKER

from

$98.99

Six piece side gear thrust washer kit for Chrysler 8″ and 9.25″.

Product Features:

Side gear thrust washer kit
Fits Chrysler 8″ and 9.25″

from

$19.99

We’ve squeezed innovation into every ounce of Valvoline FlexFill SAE 75W-140 Full Synthetic Gear Oil, the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Our unique new flexible pouch makes getting into the tightest places to lubricate gears easier than ever and with less waste. The superior detergent package-based formulation contains fully synthetic basestocks and special additives that help protect parts from rust and corrosion while providing exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity, wear resistance additives that assist in protecting gear teeth, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. Valvoline FlexFill SAE 75W-140 Full Synthetic Gear Oil is recommended for use in axle applications requiring factory-fill or drain-and-fill levels for limited slip performance.

Product Features:

FLEXIBLE POUCH FOR EASIER USE WITH LESS WASTE in tight, hard to reach undercarriage situations
EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -30F to 300F degrees for dependable coverage year-round
REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4
MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Ford M2C-192A, GM 12346140, Chrysler MS-8985 and API GL-5

from

$474.99

Product Features:

Dropout housing
Fits Chrylser 8.75″
’89’ case design
Nodular iron for added strength

from

$57.99

9.25″ cross pin shaft TracLoc ONLY, not standard Open 0.870″ DIA.

Product Features:

Cross pin shaft for Chrysler 9.25″
Fits Trac Loc positraction only
0.870″ diameter

from

$15.99

Bolt/screw for adjuster lock for Chrysler 7.25″, 8.25″, 8.75″, 9.25″.

Product Features:

Side adjuster lock bolt
Fits Chrysler 7.25″, 8.25″, 8.75″ and 9.25″

from

$67.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

Powr Lok button kit
Fits Dana Spicer 30, 44 and Chrysler 8.75″

from

$12.99

9.25″ pinion gear thrust washer.

Product Features:

Pinion gear thrust washer for Chrysler 9.25″ rear

from

$8.79

With Victor Reinz gaskets, you can be sure you are getting sealing solutions that deliver OE quality gasket technology and engineering. That is because Victor Reinz is an original equipment supplier and the trusted choice of manufacturers the world over, offering broad coverage for foreign and domestic cars and trucks. In Victor Reinz gasket sets, you get the right combination of components needed for fast, long-lasting repairs.

Product Features:

Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.

from

$22.99

Product Features:

Rubber fill plug
Fits Chrysler 7.25″, 8.25″ and 9.25″

from

$9.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$23.71

3 oz. tube, carded – OEM specified. Specially formulated to withstand the harsh gear oil environment found in differentials and transfer cases. Because gear oil has friction modifiers that break down normal RTV and cause leaking, this specialty silicone has been tested to OEM specifications to ensure complete sealing. As a gasket maker, it seeks and seals leak paths that cut gaskets cannot. It can also be used to seal cut gaskets. Suggested Applications: Differentials and transfer cases. DIRECTIONS:

Product Features:

For best results, clean and dry all surfaces with a residue-free solvent, such as Permatex® Brake and Parts Cleaner.
Cut nozzle to desired bead size: gaskets are best formed using a 1/16? to 1/4? (2 to 6 mm) bead.
Apply a continuous and even bead of silicone to one surface; surround all bolt holes. Assemble parts immediately. Finger tighten bolts until material begins to squeeze out around flange. Allow to dry for one hour then re-tighten 1/4 to 1/2 turn.
Silicone dries in 1 hour, and fully cures in 24 hours. Allow more time in cold or very dry conditions.
Replace cap after use. Note: Not recommended for use on head gaskets or parts in contact with gasoline. Store below 80°F (27°C). TECHNICAL DATA SHEET

from

$6.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$219.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M88010 race
All steel construction

from

$9.99

Chrysler 8.75″ (coarse spline) pinion nut washer.

Product Features:

Pinion nut washer
Fits Chrysler 8.75″ with 10 spline pinion

from

$59.99

RngPnnInstlKt

Popular 1971 Dodge Challenger Differentials Categories

Differential Oil

Rear Differential Cover Gaskets

Differential Open Unit and Components

Differential Pinion Shaft Lock Bolts

Differential Bearings

Differential Axle Shafts

Differential Pinion Pilot Bearings

Differential Bearing Kits

Front Differential Pinion Bearings

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Differential Cover Plugs

Differential Clutch Packs

Differential Ring and Pinions

Differential Cases

Differential End Yokes

Rear Differential Pinion Bearings

Differential Spools

Front Differential Cover Gaskets

Rear Housing Cover Gaskets

Differential Pinion Bearing Kits

Complete Differentials

Differential Ring Gear Bolts

Bearing Race Drivers

Differential Crush Sleeves

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Gear Install Kits

Differential Cross Pins

Automatic Transmission Differential Carrier Gaskets

Differential Side Gear Thrust Washers

Differential Pinion Gear Thrust Washers

Differential Pinion Gear Washers

Differential Lock Thrust Blocks

Maybe you’re in the middle of a full rebuild of that 1971 Dodge Challenger. Maybe you just need a couple of Differentials. Either way, Advance Auto Parts has 203 different Differentials in our inventory ranging from $2.49 to $1,566.99. That means you can find the exact parts or products you need to keep that 1971 Dodge Challenger running smoothly.

Differentials are only as good as their brand. We stock 12 different brands to make sure you have plenty of trusted parts to choose from for your 1971 Dodge Challenger. Driveworks, National, and Yukon Gear are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Differentials for your 1971 Dodge Challenger, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 513 reviews in this category, some of the top rated parts include DIFFERENTIAL GASKET with 3.0 stars and Differential Crush Sleeve with 5.0 stars.

So if you’re in the market for aftermarket Differentials to keep your 1971 Dodge Challenger rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Differentials Brands To Make Your 1971 Dodge Challenger Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 1971 Dodge Challenger demands trusted brand parts and products to keep it running. Many trusted brands of Differentials make up Advance Auto Parts’ inventory, and all are ready to help make your Challenger the best it can be. Be sure to browse some of our top Differentials brands and parts.

Popular Driveworks Differentials

We carry Driveworks parts in our stock across Front Differential Pinion Bearings categories, plus more. For a 1971 Dodge Challenger, our most popular Driveworks Differentials include:

from $13.99

(14)

Tapered Cone/Cup Wheel Bearing Set

Front Differential Pinion Bearings

FAQs for 1971 Dodge Challenger Differentials

What are the most purchased Differentials for the 1971 Dodge Challenger?

Out of 203 Differentials for the 1971 Dodge Challenger, the most popular in our inventory are:

from $57.99

This product is not rated

3 Qt – 80W90 Conventional Gear Oil With Posi Additive

Differential Oil

from $22.99

(3)

Bearings

Differential Bearings

from $8.99

This product is not rated

Bearings

Differential Bearings

What are the top-rated 1971 Dodge Challenger Differentials?

Top-rated Differentials for your 1971 Dodge Challenger based on customer reviews/ratings are:

from $8.29

(4)

DIFFERENTIAL GASKET

“Great Product”

from $2.49

(1)

Differential Crush Sleeve

“High quality, would buy again”

from $18.99

(1)

Multi Purpose Seal

“Perfect fit and in stock for a 50 year old vehicle. Thanks Advance Auto Parts”

1971 Dodge Challenger Differentials

More 1971 Dodge Challenger Differentials

Essential 1971 Dodge Challenger Differentials

USA Standard Gear – Open Spider Gear Set For Chrysler 9.25", 31 Spline (Part No.39004)

Motive Gear – Differential Spool (Part No.FSD60-35H)

Yukon Gear – Chrysler Fine Spline Pinion Nut For Chrysler 7.25", 8", 8.25", 8.75", And 9.25" (Part No.33253)

Yukon Gear – Redi-Sleeve Yoke Saver For 8.75" C, 9.25" C, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD (Part No.30228)

Yukon Gear – Crush Sleeve (Part No.33094)

Felpro – DIFFERENTIAL GASKET (Part No.RDS 6095-1)

Yukon Gear – Pinion Install Kit For Chrysler 8.75" (#41) Differential (Part No.13005)

Powertrax – Grip LOK Traction System (Part No.LK436035)

Yukon Gear – Standard Open Notched Cross Pin Shaft For 9.25" Chrysler (Part No.33309)

Yukon Gear – Minor Install Kit For Chrysler 42 8.75" Differential (Part No.12006)

Yukon Gear – Ring Gear Bolt For Chrysler 9.25" Rear (Part No.33033)

Driveworks – Taper Bearing Set (Part No.S-A-18)

Motive Gear – Differential Bearing Kit – Koyo (Part No.R8.75RLA)

Yukon Gear – Six Piece Side Gear And Thrust Washer Kit For Chrysler 8" And 9.25" (Part No.33278)

Valvoline – Flex Fill Transmission & Differential Gear Oil: Full Synthetic 75W-140, 1 Quart (Part No.889787)

USA Standard Gear – 8.75" Chrysler 89 Drop Out Case, Up To 500 Hp, Nodular Iron (Part No.59001)

Yukon Gear – 9.25" Cross Pin Shaft Tracloc Only, Not Standard Open 0.870" Diameter (Part No.33310)

Yukon Gear – Bolt/Screw For Adjuster Lock For Chrysler 7.25", 8.25", 8.75", 9.25" (Part No.33233)

Yukon Gear – Powr Lok Button Kit For Dana 30, Dana 44 & Chrysler 8.75" (Part No.33536)

Yukon Gear – 9.25" Pinion Gear Thrust Washer (Part No.33274)

Victor Reinz – Differential Cover Gasket (Part No.71-14868-00)

Yukon Gear – Rubber Fill Plug For Chrysler (Part No.33463)

National – Bearings (Part No.M86610)

Permatex – Gear Oil RTV Gasket Maker (Part No.3G350374768PMX)

Felpro – Differential Carrier Gasket (Part No.RDS 6583)

Yukon Gear – Bearing Race Driver (Part No.56023)

Yukon Gear – Chrysler 8.75" (Coarse Spline) Pinion Nut Washer (Part No.33162)

Richmond Gear – RngPnnInstlKt (Part No.83-1034-B)

Popular 1971 Dodge Challenger Differentials Categories