from

$165.99

This Spectre Oil Pan was designed for the big block Chrysler/Dodge/Plymouth 383, 400, 413, 426, & 440 engines. This triple chrome plated oil pan is made to replace the oem oil pan.

Product Features:

Triple chrome-plated
Steel construction
Stock capacity
Made from high quality material

from

$79.99

Put an end to high maintenance points ignition systems by installing an ACCEL points eliminator ignition conversion kit. By utilizing specialized electronic circuitry and an infrared signal, ignition timing is stable from 1 to 10,000 RPM. More accurate ignition timing than any other type of system. Improves performance and fuel efficiency. Easy to install with simple hand tools. Reduced maintenance-eliminates changing points forever. Latest thermal clad based surface mount construction for maximum dependability and long life. Available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

More Accurate Ignition Timing
Improves Performance
Provides More Accurate Ignition Timing
Easy To Install w/Hand Tools
Reduced Maintenance
Thermal Clad Based Surface Mount Construction
Utilizes Specialized Electronic Circuitry
Ignition Timing Is Stable From 1 To 10000rpm

from

$16.99

FRAM Racing® filters are designed with a heavy-gauge tapping plate and an extra-thick* steel can that is able to withstand the high pressure flexing caused by demanding driving conditions. A spiral-shaped center tube provides protection against collapse, and tough steel end caps add even more durability. A screen-over 22psi filter bypass valve provides additional protection against larger contaminants.**

Product Features:

Proven protection for up to 10,000 miles
Engineered for use with synthetic or conventional motor oils
Filter media is a blend of fiber and resin that captures 95% of the dirt particles
The perfect balance of dirt-trapping efficiency and dirt-holding capacity

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens at 160 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Stainless Steel, Copper & Brass Construction – Resists Corrosion
High Flow

from

$60.29

Copperseal exhaust gaskets are unique gaskets made from .043 inch solid copper. They feature an embossed O-ring design for a leak proof seal. They won’t shrink, deteriorate or blowout. Header bolts stay tight. Ideal for motor homes and towing.

Product Features:

Will Not Shrink/Deteriorate
Creates A Tight Leak Proof Seal
Helps Lower Under hood Temps
Seals Irregular Surfaces
Seals Slightly Damaged Surface
Ideal For Tow Vehicles
Ideal For Motor Homes

from

$24.99

A true performance application component for cars, trucks, hot rod, for racing and competition, yet popularly used for street vehicles when more horsepower is added. Soft running enough to absorb vibrations for street use yet rugged for racing use. Helps control torque on high performance vehicles. Maintains proper drive shaft angle to help prevent early wear and unexpected power train damage. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal transmission mounts. Resistant to under vehicle fluid oils, coolants and road contaminants. Made of Energy’s Hyper-Flex performance polyurethane and heavy duty hardware – for added durability.

Product Features:

Made from HYPER-Flex Polyurethane
Firm Enough for Huge Amounts of Horsepower/Torque
Soft Enough Not to Transmit Vibration

from

$85.29

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

Service Part
No Moving Parts To Wear Out
Self Contained Unit
Can Drive OEM
Can Drive High Performance Ignition Coils

from

$96.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets

from

$409.99

MSD Pro-Billet Distributors are the finest performance and racing distributors available. Every feature has been engineered to endure the rigors of high performance and racing engines. Whether cruising the streets or racing stock cars, dragsters, boats or trucks, MSD has a distributor for it. MSD uses state-of-the-art, Computer Numerical Controlled (CNC) mills and lathes to machine each housing. After a long series of precise cuts and movements, the billet is formed into a flawless distributor housing that is accurate to within 0.001″. The flex-free housings are lightweight, have no porosity or weak areas and look great on polished, show quality engines.

Product Features:

Smaller diameter CNC machined billet aluminum housing
Must Be Used w/An MSD Ignition Control
Supplied w/small dia. cap w/HEI style terminals; race and rotor
Nylon pads ensure smooth operation of the advance weights
Advance weight pins are staked and tig welded to the plate
Mech. advance assem. can be locked out for crank trigger systems
Advance plate and weights are fine blanked from chrome moly steel
QPQ coated for friction reduction
Maintenance-free magnetic pickup and precision reluctor
Creates stable trigger signals throughout the rpm range
Easy-to-adjust mech. advance w/supplied springs and stop bushings
No CARB Exemption Order Number

from

$154.99

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1971-92 Chrysler, Dodge and Plymouth (externally balanced) 360ci V8 engine (6-bolt crankshaft flange) and A727 transmission. Features include high tensile strength steel construction to resist elongation and cracking, 10.00 and 11.125 inch bolt patterns and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953.

Product Features:

NHRA/IHRA Legal For All Classes
Includes SFI Certification Sticker
Ideal For Street Applications
To Extreme Duty Racing
To High RPM Use

from

$17.79

Fuel pump mounting pad cover is used to cover the hole in the block when the mechanical fuel pump is removed to use an electric pump.

Product Features:

Mechanical Fuel Pump Mounting Pad Cover For Chrysler V-8ft.S

from

$612.99

Edelbrock part #75763 RPM Air-Gap intake manifold is designed for 340-360 c.i.d. Chrysler V8’s and 318 c.i.d. engines with 340-360 cylinder heads. The RPM Air-Gap incorporates the same race-winning technology that’s been used on our Victor Series competit

Product Features:

1500-6500 RPM Range
Dual Plane Type-4150 Style Flange
4.9 in. Front Height, 5.35 in. Center Height, 5.8 in. Rear Height
Black Powder Coated Finish
Made In The USA

from

$42.49

Excellent high performance replacement for import and domestic vehicles with canister type oil filled coil. Re-engineered windings for even higher energy output resulting in quicker starting improved throttle response and more high RPM power. Designed to work with Points style and Breakerless electronic ignition systems. Heavy duty black Alkyd tower provides in flashover in protection to primary terminals. ACCEL Yellow can. 42000 volts effective up to 6500 RPM 1.4 ohms on the primary

Product Features:

42000 Volts
Effective To 6500 RPM
Quicker Starting
Improved Throttle Response
Higher RPM Power
Can Finished In Yellow

from

$27.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

from

$12.09

If you have custom steel or mag wheels that are not designed without a provision for a center cap, you’re probably looking at an ugly stock dust cap in the center of your front wheels. This chrome dust cap fixes that problem, and is a direct replacement for stock cap 1.790 inches in diameter. Two per set.

Product Features:

Chrome Plated Steel
Set of 2 Caps
Easy Installation
2 Per Set

from

$499.99

The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, New turbine hub and dual pattern drive lugs on some Holeshots.

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$48.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$32.09

These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:

Features 12-point Smaller-than-standard Bolt Head
Thick Flat Washers Distribute Optimum Clamp Load
Ideal Use Where Space Is Minimal On Race Manifolds
Bolts And Washers Zinc Plated For Protection
Zinc Plated For Protection

from

$23.79

Spectre’s Chrysler water neck fits 1964 and later Chrysler V8 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes bolts.

Product Features:

Fits 1964 and later Chrysler V8 engines
Includes bolts
Chrome plated
Easy to install
O-ring/gasket not included

from

$14.29

Chrome plated breather cap is ideal for race car vacuum balance systems, as well as original equipment applications with positive crankcase ventilation (PCV).

Product Features:

Features 1″ O.D. neck and a 5/8″ O.D. breather tube
Breather has Metal/Foam Baffle inside and includes Grommet
Fits all aftermarket valve covers with a 1.22″ Dia. opening

from

$32.59

Product Features:

Prevents Air Inclusion
Direct Replacement
For OE Bleeders
One Person Bleeds Safely
Without The Mess
No Chance Of Air Bubbles

from

$438.99

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

from

$31.99

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Product Features:

Work with .530″ guides and 3/8″ valve stem diameter
Valve stem oil seals keep unwanted oil from entering the combustion chamber
Several different types of valve seals are offered

from

$22.49

When installing headers you will need header bolts, factory exhaust manifold bolts won’t work. These Mr. Gasket Header Bolts are Grade 5 for strength, black oxide coated, and have a compact hex head that is ideal for use where space is minimal – your typical header flanges. Sold as a set of 14.

Product Features:

14 per Package
Heat-Treated For Strength
Ideal For Tight Spaces
Grade 5 Material
Protective Black Finish

from

$166.99

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1971-up Chrysler, Dodge and Plymouth 383, 400 and 440ci (externally balanced cast crankshaft) V8 engines with A727 transmission. Features include high tensile strength steel construction to resist elongation and cracking, 10.00 and 11.125 inch bolt patterns and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953.

Product Features:

NHRA/IHRA Legal For All Classes
Includes SFI Certification Sticker
Ideal For Street Applications
To Extreme Duty Racing
To High RPM Use

from

$64.99

Available in various sizes, heights, and finishes, Spectre offers a wide variety of high performance valve covers designed to easily replace your stock covers. Designed for 1965-1991 Chrysler 273-318-340-360 engines, this valve cover features chrome-plated steel construction and a smooth design. Sold in pairs, this stock profile cover is baffled to provide optimum function. With show quality construction and a sealing edge designed for an ideal fit, our valve covers are engineered to look great for applications ranging from custom builds to replacing stock equipment.

Product Features:

Designed for 1965-1991 Chrysler 273-318-340-360 engines
Baffled for breather system compatibility
Sold in pairs
Triple chrome-plated steel construction
Stock height
Features OEM style sealing edge

from

$102.99

K&N performance High-Flow Air Filters are engineered to improve engine performance. Unlike disposable paper filters which must be frequently replaced, K&N Air Filters are washable, reusable, and engineered to last for the life of your vehicle or outdoor power small engine. Engineered to fit easily into your factory air box, installation can be completed in a matter of minutes! K&N develops and tests each product on the world┐s toughest race tracks, so we can bring the highest level of performance to your daily driving. Join the millions of customers who have saved money and improved vehicle performance by upgrading to K&N filtration.

Product Features:

ENGINEERED POWER: State-of-the-art air filter media is designed to increase horsepower and acceleration as well as improve overall engine performance
RUGGED CONSTRUCTION: K&N Air Filters are manufactured with durable, premium materials and state-of-the-art construction methods to last a lifetime
4 LAYERS OF PROTECTION: Multiple layers of premium cotton gauze treated with a specially-designed tacking agent work together to create an intricate mesh of engine filter media that is designed to block and trap harmful contaminants
CLEAN ONCE EVERY 5 YEARS: Engine air filter only needs cleaning every 75,000 miles under normal highway driving conditions (based on the average miles driven per year of 15,000 miles)
ULTIMATE LONGEVITY: No-hassle lifetime warranty on stock replacement K&N air filters- limitations apply
EASY INSTALLATION: K&N Air Filters are pre-treated and ready to drop into your factory air box- they are one of the easiest and most cost-effective vehicle upgrades for quick performance gains
ECO-FRIENDLY: Using a washable, reusable engine air filter helps reduce replacement air filter waste- a K&N air filter is designed to last longer than 10 or more disposable filters
MADE IN USA: K&N Air Filters are proudly made in the USA for trusted quality & reliability

from

$53.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features: