1970 Chevrolet Chevelle Performance Engines

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

Magnum Pushrods from COMP Cams offer an affordable solution for your .080″ wall chromemoly pushrod needs. Designed to withstand the stresses of a high performance engine, Magnum Pushrods are head-treated for extended durability and have precision formed, reinforced ends. Magnum Pushrods are black-oxide finished with their part number and length laser etched onto the surface for easy identification.

Product Features:

• 3/8″ Diameter, 7.800″ Length
• Magnum Pushrods for Small Block Chevy
• One-piece .080″ wall chromemoly steel tubing
• Heat-treated for extended durability and guide plate compatibility
• Precision formed and reinforced pushrod end

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

• Manufactured from cellulose/nitrile composition gasket material
• Provides excellent sealing and durability
• Die-cut for an excellent fit
• Can be trimmed if necessary for modified port applications
• For OE replacement, high performance street, drag race and oval track use

Mr. Gasket Steel Shim Cylinder Head Gaskets are for high performance street machines, drag racing and oval track racing. With today’s extreme compression ratios you need stronger more durable gaskets. Mr. Gasket steel shim gaskets are made from .020 inch steel shim stock which is thinner than most composite gaskets increasing engine compression. Stress formed embossments will seal the extreme cylinder pressure.

Product Features:

• Manufactured from .020″ steel shim stock.
• Thinner than composition head gaskets – increases engine compression.
• Stress formed embossments seal extreme cylinder pressures.
• For high performance street, drag race and oval track use.

Molded rubber gaskets are reusable, great for engines that require valve lash maintenance. These gaskets feature Nitrile material for long life, solid steel carrier for strength and rigidity. Incorporates compression limiters to prevent fastener over-tightening.

Product Features:

• Features Nitrile Rubber Material For Long Life
• Molded Rubber Gaskets Are Reusable
• Ideal For Engine Requiring Valve Lash Maintenance

Product Features:

• Replacement Gasket Set For PN[4242]

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
• With steel core to provide ultimate excellent blowout resistance.
• Not intended for use in emission controlled vehicles.

BIG BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Big Mutha’ Thumpr: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.

Product Features:

• Cam and lifter kit for Big Block Chevy engines
• CL-Kit includes cam, lifters, assembly lube, instructions and decals
• HYDRAULIC – Big Mutha’ Thumpr: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.
• 295/312 Advertised Duration, 243/257 Duration @ .050″, .522″/.507″ Lift, 107 Lobe Separation
• Valve spring upgrade required

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:

• Repairs That Leaky Rear Main Sail
• Silicone Rubber to Withstand Extreme Engine Oil Temperatures
• Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
• Injection Molded for Precise Fit

Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

Product Features:

• 8″ diameter
• 1970-73, 396-427-454 cu. in.
• 1967-69, 302 cu. in.
• 1965-68, 327 cu. in. hi-performance
• 1970-76, 400 cu. in.
• 1970-73, 350 cu. in.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

• Excellent performance in street carbureted applications.
• More vacuum allows an increase in duration for improved performance and assists power brakes.
• Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
• Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

Chrome water neck with a swivel top allows you to place your coolant hose where you want it to be, not just where the neck allows. Precision die cast for better fitment, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:

• Chrome Plated Aluminum
• O-ring To Prevent Leaks
• Swivels For Hard To Fit Applications
• Comes With Allen Head Bolts

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 180 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

These grade 8 alloy steel, longer length bolts are designed to compensate for thread length lost when using head bolt washers. This allows increased torque and clamping. Set of 16 does one cylinder head.

Product Features:

• Cylinder Head Bolts
• Longer-Than-Stock
• High Quality Grade 8 Alloy
• Increase Torque Settings
• Higher Clamp Loads On Gasket

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

• Zinc plated to resist corrosion and provide a clean professional appearance
• Made from Grade 5 steel for strength and durability
• Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
• Allen (socket) Head
• Zinc Plated For Protection

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• Complete Kit: Includes Retainers And Locks
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Includes Superior Quality Steel Retainers
• Includes 7 deg. Heat-Treated Valve Stem Locks
• Retainers and Locks Black Oxide Coated
• Non-Rotator Style: Dyno Tested and Street Proven
• Great Match to Edelbrock Camshaft Kit

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:

• Maximum Cooling for Street and Racing Engines
• Internal Passages Are Balanced for Maximum Flow
• Impeller is Larger than Others For Max Pressure
• Impeller Vanes Dramatically Increase Flow Rates
• Equal Distribution to Both Sides of Block
• Only Flows in One-Direction for Optimum Efficiency

Big Block Chevrolet tubular head dowel, .638/.639 inch o.d. (outer diameter) by 1/2 inch. Packaged two per set. These hard to find dowel pins are precision machined then case hardened for accurate alignment in engine assembly.

Product Features:

• Precision Machined
• Case Hardened
• Give Accurate Alignment
• 2 Per Set

Product Features:

• Use W/ Valve Springs Part #5703, 5794
• Set of 16
• 1.50 in. Outside Diameter
• Steel Material
• Black Oxide Finish

Edelbrock camshafts are matched to Edelbrock Total Power Package components for proven performance, taking the guesswork out of camshaft selection. They are compatible with OEM or Edelbrock hydraulic roller tappets which reduce friction, virtually eliminate break-in problems, and permit higher valve velocities for increased performance. Designed to work with Torker II manifolds for performance from 2500 to 6500 RPM, these camshafts are ideal for high-performance street, drag or marine applications. Torker-Plus cams have a slightly rough idle and are not suitable for trucks or towing applications. Hydraulic flat tappet lifters are included with each camshaft.

Product Features:

• Designed for 2500 to 6500 Performance
• Designed for Hi-Perf Street; Drag or Marine Use
• Matched to Edelbrock Torker II Intakes
• Includes Hydraulic Lifters and Assembly Lube
• Dyno Matched/Street Proven Performance
• Take The Guesswork Out Of Camshaft Selection

These are high quality nuts with allen set screws to provide you with that positive lock needed for Race or original equipment Rocker Arms.

Product Features:

• They Are Zinc Dichromate Plated Steel
• They Have Black Oxide Coated Set Screws
• Keeps Rocker Arms Positively Locked
• (16) Rocker Arm Nuts w/ Locks 3/8″-24 Threads
• Includes Locks and Hex Wrench
• Shank O.D. .603″

Mr. Gasket screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street applications. OE style press in rocker studs can actually pull out of the cylinder head when using high lift camshafts. Includes sixteen studs 3/8-24 x 1.47 inch long top x 7/16-14 bottom.

Product Features:

• Black Oxide Coated Grade 8 Steel
• Kit Contains 16 Studs
• Easy To Install
• Heat Treated Steel
• Grade 8 Steel

With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:

• Advance the cam for increased torque and horsepower
• Tune your powerband for more end torque or increase top end horsepower
• Includes (4) offset bushings and (1) 0 degree bushing
• Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
• Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
• Increase Top-End Horsepower

Product Features:

• Solid Bushing Chain Resists Stretching
• For Use with Stock or Edelbrock Camshafts
• Stressproof Steel Crank Gears
• 3 Keyway Setting Points To Ensure Accurate Timing
• True Bearing Surface Rolls with the Sprockets

Product Features:

• 50-State Street Legal Aluminum Cylinder Head
• Out-of-the-Box Bolt-On Performance
• 70cc Combustion Chambers Improve Performance
• Retain Stock Compression Ratio

Product Features:

• 50-State Street Legal Aluminum Cylinder Head
• Out-of-the-Box Bolt-On Performance
• 64cc Combustion Chambers Improve Performance
• Retain Stock Compression Ratio

Product Features:

• 2000-6500 RPM Power Band
• Single Plane/Open Plenum Design
• No Provision For Divorced Or Hot Air Choke
• Square Flange Carburetor Mounting

For 3500 to 7500 PRM. Use where low-end torque is not a prime factor. Great for engines with slightly modified heads. HEI ignition will not clear manifold. Street machines, street rods, pro-street and marine.

Product Features:

• For 3500 to 7500 RPM
• Use Where Low-End Torque is Not a Prime Factor
• Great For Engines w/Slightly Modified Heads
• Top Has Vacuum Outlet for Power Brakes
• Will Accept Forward and Sideways Mounted Carbs
• Carburetor Center-to-Center Dimensions 9.38 in
• HEI Ignition Will Not Clear Manifold
• Street Machines; Street Rods; Pro-Street; Marine