1970 Chevrolet Blazer Drivetrains
More 1970 Chevrolet Blazer Drivetrains Categories
If you’re looking for an original Drivetrains replacement for a 1970 Chevrolet Blazer, you can search through our selection below. You’ll also find aftermarket and OEM Drivetrains to meet your needs.
Essential 1970 Chevrolet Blazer Drivetrains
Yukon Gear – Dana 44 Front Axle Bearing And Seal Kit Replacement (Part No.10022)
from
$121.99
Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. Replacement Axle bearing and seal kit for ’57 to ’77 Dana 44 and Chevy/GM 1/2 ton front axle. This kit includes Timken inner and outer bearings and races along with high quality seals. Unit is sold per side and is covered for one year against manufacturing defects. This axle bearing & seal kit services one side only.
Product Features:
See More
Product Features:
- Fits 1957-1977 GM 1/2 ton
- Includes axle bearings, races and seal
- Services one side
MOOG Driveline Products – Double Cardan CV H Yoke (Part No.647)
from
$71.99
By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.
Product Features:
See More
Product Features:
- Machined bodies to meet the tight tolerances
- Forged and cast material to meet the performance requirement
- Minimize the flash lines for less interference
- Cleaning process induces compressive strength for increased performance
- Machined and threaded holes for mounting ease
- Rust preventative added for longer shelf life
Motive Gear – Differential Carrier Shim Kit (Part No.1101)
from
$8.49
High-quality Differential Carrier Shim Kit
Product Features:
See More
Product Features:
- CARRIER SHIMS 12 BOLT GM CAR & TRUCK ALSO GM8.6″ 99-ON
Yukon Gear – Positraction Shim Kit (18 Shims) For GM 8.2", GM 8.5", 12T, 12P, Ford 8.8" & Cast Iron ‘Vette (Part No.16042)
from
$41.99
Product Features:
See More
- Shim kit
- Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
Driveworks – Tapered Roller Bearing (Part No.S-HM-88648)
Yukon Gear – Dana 30 & Dana 44 Power Lok Bolt, Left Hand, & 8.75" Chrysler & 55P (Part No.33234)
from
$26.99
Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.
Product Features:
See More
Product Features:
- Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
- Left hand thread
ACDelco – Trans Case Input Sft (Part No.J7110341646ACD)
from
$107.03
Trans Case Input Sft
National – Bearings (Part No.31520)
from
$12.29
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Yukon Gear – Drive Flange Cap For Dana 44 (Part No.32134)
National – Multi Purpose Seal (Part No.710046)
from
$17.99
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Low swell in hydrocarbon fluids
- Design type: spring loaded; multi-lip
- Provides good low temperature capability
- Temperature range: -40°F to 225°F; -40°C to 107°C
- Delivers quality and reliable performance for every type of repair
National – Bearings (Part No.M802011)
from
$14.79
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Milemarker – Spindle Nut Socket (Part No.15002-01)
Yukon Gear – Replacement Front Axle Inner Seal Redi-Sleeve For Dana 44 & 8.5" GM (Part No.30219)
from
$83.99
Replacement front axle inner seal redi-sleeve for Dana 44 & 8.5″ GM.Yukon Mighty seal.
Product Features:
See More
Product Features:
- Axle Redi-sleeve
- Fits Dana Spicer 44
USA Standard Gear – Master Overhaul Kit for the GM 8.5 Differential with HD Posi or Locker (Part No.37057)
from
$208.99
USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.
Product Features:
See More
Product Features:
- Fits GM 8.5″ rear with aftermarket positraction
- Uses Koyo bearings and races
- Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.
Yukon Gear – Replacement Outer Oil Slinger For Dana 25, 27, 30, 44 & 50 (Part No.33011)
Pro-King – Differential Case (Empty) (Part No.714A714A)
from
$159.99
Pro-King is the leading supplier of transmission and driveline products in the aftermarket.
Product Features:
See More
Product Features:
- All products are designed to meet or exceed OE quality, form, fit and funtion.
Yukon Gear – Redline Synthetic "Shock Proof" Oil With Positraction Additive – 4 Quarts (Part No.15005)
from
$148.99
Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.
Product Features:
See More
Product Features:
- Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive
Yukon Gear – 8.6" GM 12P 12T & F8.8 Carrier Installation Kit (Part No.57010)
from
$121.99
Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.6″, 12 bolt car and 12 bolt truck differential. This kit contains carrier bearings, races and shims.
Product Features:
See More
Product Features:
- Fits GM 12 bolt passenger car and truck and 8.6″
- Includes carrier bearings and races and “super” carrier shim kit
Motive Gear – Differential Pinion Shim Kit (Part No.1114)
Yukon Gear – Replacement Carrier Shim Kit For Dana Spicer 44, 30 Spline Axles (Part No.55010)
USA Standard Gear – Spartan Locker For GM 12 Bolt Car & Truck With 30 Spline Axles, Includes Heavy-Duty Cross Pin Shaft (Part No.17032)
from
$672.99
The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.
Product Features:
See More
Product Features:
- Fits GM 12 bolt car and truck with 30 spline axles
- Made from 9310 steel for added strength
- Replaces the spiders in a standard carrier case
Yukon Gear – Dana 44, Ford 8" / 9", And Model 20 Side Gear Thrust Washer Replacement (Part No.33283)
from
$5.99
Product Features:
See More
- Side gear thrust washer for Ford 8″, Ford 9″ and AMC Model 20
- 0.030″ thick
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6091)
from
$103.99
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CHEV 88-12; GMC 94-12;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1988-2012
- Weight approx: 3 Lbs
- BEARING ID / BORE: 1.5750 INCH / 40 MM
- CENTERLINE: 2.28 INCH / 58 MM
- MOUNT WIDTH: 6.62 INCH / 168 MM
- WITHOUT PLATE
- WITH STUDS
Yukon Gear – Positraction Clutch Guide (Part No.33352)
from
$8.99
Positraction clutch guide.
Product Features:
See More
Product Features:
- Clutch guide for Chrysler 9.25″, Dana Spicer 44, Dana Spicer 50, Ford 8.8″, GM 12 bolt passenger car, GM 8.2″, 8.5″ and 8.6″, 1963-1979 Corvette and Nissan Titan
- Compatible with Dura Grip positractions only
MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.377)
from
$47.99
Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.
Product Features:
See More
Product Features:
- BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
- COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
- CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
- GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
- KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
- RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Dorman – Help – Differential Shaft Lock Bolt (Part No.81048)
from
$5.99
This differential pinion shaft lock bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Driveworks – Ball Bearing (Part No.S-HB-88107-A)
National – Multi Purpose Bearing (Part No.HB-206-FF)
from
$46.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Controlled heat treating process for lasting performance and extended bearing life
- Industry leading coverage
- Professional technicians know they can depend on National
Popular 1970 Chevrolet Blazer Drivetrains Categories
1970 Chevrolet Blazer Drivetrains
You count on your 1970 Chevrolet Blazer to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Drivetrains. With 433 Drivetrains ranging in price from $3.99 to $1,674.99, you’re sure to find everything you need for your 1970 Chevrolet Blazer.
Brands matter. If you want to shop a specific Drivetrains brand, we stock 23 different brands like Valvoline, Moog, and National. 1970 Chevrolet Blazer Drivetrains start as low as $3.99!
One of the best ways to find top quality OEM or aftermarket Drivetrains is by asking professionals. Short of that, you can shop with confidence thanks to our 8,941 extensive product reviews on 1970 Chevrolet Blazer Drivetrains. Some of the top-rated Drivetrains products we carry are Greaseable Super Strength Universal Joint with 4.6 stars and Greaseable Premium Universal Joint with 4.0 stars.
Did we mention you can order your Drivetrains from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Drivetrains inventory for your 1970 Chevrolet Blazer below to get started!
Top-Rated Drivetrains Brands For Your 1970 Chevrolet Blazer
Trusted Drivetrains OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1970 Chevrolet Blazer running right for years to come. In our inventory you’ll find brands like Valvoline, Moog, National, and even more.
Popular Valvoline Drivetrains
You’ll find popular Valvoline brand products across Differentials. All are waiting to get your 1970 Chevrolet Blazer back on the road. Some of the top-rated Valvoline products in these categories are:
from
$12.79
(446)
MaxLife Multi-Vehicle (ATF) Full Synthetic Automatic Transmission Fluid, 1 Quart
Differential Oil
FAQs for 1970 Chevrolet Blazer Drivetrains
What are the most purchased Drivetrains for the 1970 Chevrolet Blazer?
Out of 433 Drivetrains for the 1970 Chevrolet Blazer, the most popular in our inventory are:
What are the top-rated 1970 Chevrolet Blazer Drivetrains?
Top-rated Drivetrains for your 1970 Chevrolet Blazer based on customer reviews/ratings are:
from
$32.99
(37)
Greaseable Super Strength Universal Joint
“grease fitting I like location dont like needle design to grease should be regular design fitting”
