1969 GMC C15/C1500 Pickup Differentials

Product Features:

• Super carrier shim kit for Ford 8.8″, GM 12 bolt passenger car and truck, GM 8.0″, 8.6″, 8.6″ IRS and 1963-1979 Corvette
• Interlocking design makes installation much easier

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Design type: spring loaded; multi-lip
• Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
• Resistance to EP lubricants
• Low swell in hydrocarbon fluids
• Delivers quality and reliable performance for every type of repair

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

• Redi-Sleeve yoke saver
• Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

Dana 60 & Dana 70 Power Lok case bolt.

Product Features:

• Power Lok case bolt for Dana Spicer 60 and 70
• 7/16 x 14 thread
• 3.5″ long
• 9/16″ hex head

Yukon replacement standard open spider gear kit for Dana 60 with 30 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Dana Spicer 60 open differential with 30 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

• DANA-60 BRG & SEAL KIT-UP TO 98 FRD

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

• Fits Dana Spicer 44 with 30 spline axles
• Made from 9310 steel for added strength
• Replaces the spiders in a standard carrier case

Differential

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Product Features:

• Shim kit
• Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction

Product Features:

• Cover gasket
• Fits Dana Spicer 60, 70, 70U and 70HD

Seal housing for Dana 60, Zip locker, with o-rings.

Product Features:

• Seal housing for Dana Spicer 60
• Includes o-rings

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush. (Includes Supershims).

Product Features:

• Fits GM 12 bolt truck
• Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

Replacement pinion nut washer for Dana 25, 27, 30, 36, 44 & 53.

Product Features:

• Pinion nut washer for Dana Spicer 25, 27, 30, 44 and 50

Air line repair kit, ZIP locker.

Product Features:

• Air line repair kit
• Includes 20′ air line and two repair fittings

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

• Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Dana 44 differential. This kit contains carrier bearings, races and shims.

Product Features:

• Fits Dana Spicer 44
• Includes carrier bearings and races and carrier shim kit

3/8″ ring gear bolt washer for GM 12 bolt car & truck, 8.2 BOP & more.

Product Features:

• Ring gear bolt washer for GM 12 bolt car and truck, 1955-1964 passenger car, 1963-1979 Corvette and 8.2″ Buick, Oldsmobile and Pontiac

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits GM 12 bolt truck
• Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

USA Standard axle for ’71-’81 2WD GM Truck. 12 bolt differential, 31 7/16″, 5 lug, 30 spline.

Product Features:

• Fits 1970-1981 GM 12 bolt truck with 2 wheel drive
• 30 spline
• 31 7/16″ long
• 5 lug

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

Standard Open and positraction cross pin shaft for GM 12T, 12P, and 55T.

Product Features:

• Cross pin shaft for GM 12 bolt passenger car and truck
• Fits standard open and positraction applications

Product Features:

• CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN: Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Positraction clutch guide.

Product Features:

• Clutch guide for Chrysler 9.25″, Dana Spicer 44, Dana Spicer 50, Ford 8.8″, GM 12 bolt passenger car, GM 8.2″, 8.5″ and 8.6″, 1963-1979 Corvette and Nissan Titan
• Compatible with Dura Grip positractions only

RngPnn

Product Features:

• Clutch kit
• Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
• 14 piece kit
• Composite clutches

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver selectability. The Yukon Zip locker is an air operated locker that provides selectable traction for off road or street use. This unit features 4320 Chrome Moly internals for added strength. Assembled in the USA! compressor sold separately. All Zip Lockers are backed by the best warranty in the business! All Zip Lockers come with a six (6) year warranty, including any collaterally damaged parts and associated labor, up to $2,000, for the first two (2) years.

Product Features:

• Fits Dana Spicer 44 with 30 spline axles
• 3.73 and down ratio only
• Forged case and 8620 internals for added strength
• Works with a variety of air delivery systems
• Assembled in the USA