1969 Buick Wildcat Performance and Racing Products

Below you will find various in-demand Buick Performance and Racing Products, components and accessories for your 1969 Wildcat. Advance Auto Parts has popular Wildcat parts like Performance Fuel Systems, Performance Oil Filters, Performance Air Filters and more. You’ll also find aftermarket and OEM Performance and Racing Products for other Wildcat model years including 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1970 and more. Select a category of 1969 Buick Wildcat Performance and Racing Products below and start saving instantly.

Please Select your Vehicle to See Exact Fit Parts

Popular 1969 Buick Wildcat Performance and Racing Products Categories

Performance Oil Filters

Performance Carburetors

Performance Engine Coolant Thermostats

Performance Air Filters

Performance Coils

Performance Distributor Cap and Rotor Kits

Performance Shifters

Performance Distributors

Performance Transmission Dipstick Tubes

Performance Water Outlets

Performance Engine Cylinder Head Gaskets

Performance Engine Intake Manifold Gaskets

Performance Coil Spring Insulators

Performance Clutch Pressure Plate and Disc Sets

Performance Engine Valve Springs

Performance Engine Valve Cover Gasket Sets

Performance Flywheel and Flexplates

Performance Exhaust Manifold Gaskets

Performance Ignition Kits

Performance Upper Performance Control Arm Bushings

Performance Engine Camshafts

Performance Ring and Pinions

Performance Ignition Parts

Performance Points and Condensers

Performance Lower Control Arm Bushings

Performance Engine Valve Lifters

Performance Tie Rod End Boots

Performance Transmission Shift Kits

Performance Engine Push Rods

Performance Torque Converters

Performance Engine Valve Stem Seal Sets

Performance Transmission Rebuild Kits

Essential Performance and Racing Products for 1969 Buick Wildcats

from

$5.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Saves Your Tie Rods
Lasts Longer
Looks Great

from

$179.99

Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

Easy Installation
Improved Fuel Economy
Reduced Maintenance
Accurate Timing
Improved Performance
Provides A Simple Conversion
No Moving Parts To Wear Out

from

$34.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

from

$417.99

RngPnn

from

$869.99

The ultimate shifter for automatic transmission equipped street vehicles! The Hi-Tek Street bandit has all the same feature as the above Street Bandit line of shifters, with an interchangeable billet knob design.

Product Features:

Ideal For High-Tech Pro-Street
Ideal For High-Tech Street Rods
Narrow Styled Aluminum Housing
Includes Neutral Safety Switch
Includes Backup Light Switch
Includes Billet Aluminum Knob
Can Be Used w/Reverse Pattern Valve Body

from

$34.49

Product Features:

Service Part
Makes Connections Quick And Easy

from

$54.99

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$167.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$511.99

A B&M transmission in a box! Transform your automatic transmission into a full-tilt B&M performer! This is our ultimate transmission kit – it comes complete with full instructions on how to assemble your transmission to B&M specifications.

Product Features:

High Perf. Friction Materials
Complete Overhaul Gasket Set
Modification Components
Replacement Valves
Replacement Springs
Drain Plug Kit Included

from

$149.99

Product Features:

Non-Rotator Type
1.550 in. Outer Diameter
.190 Wire Size
Single Coil Spring Type
Set of 16

from

$33.99

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Product Features:

Work with .530″ guides and 3/8″ valve stem diameter
Valve stem oil seals keep unwanted oil from entering the combustion chamber
Several different types of valve seals are offered

from

$31.99

This Spectre OEM replacement air filter is an easy to install performance option for multiple Buick, Cadillac, Chevy, GM, Mercedes, Oldsmobile and Pontiac applications that use a 14 inch by 3 inch round air filter. With its performance synthetic air filter media, this air filter has been designed to add horsepower and quicker acceleration by allowing more air flow into your engine than ordinary paper filters. This air filter’s sealing edge was engineered to insure a proper air cleaner housing seal for great engine protection.

Product Features:

Replacement for 14 inch by 3 inch round air filter
Fits perfectly in your vehicle’s air box as a replacement for your factory air filter
Engineered for increased flow and greater performance
Fits select Buick, Cadillac, Chevy, GM, Mercedes, Oldsmobile and Pontiac models
Factory pre-oiled and ready to use
Simple installation

from

$699.99

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

Vibratory Polished For Good Looks
Optimized Street Calibration That Works Out Of The Box
Factory Preset Electric Choke For Easy Startups
Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
No Unnecessary Trips Back To The Parts Store
Limited Lifetime Warranty
100% Wet Flow Tested By Holley Technicians
Arrives Ready To Run

from

$19.29

Distributor Condenser

from

$13.29

Made of superior Hyper-Flex material. Saves replacing again and again, lasting 3 to 10 times longer. Assemble to chassis the same way as OEM isolators and do not adversely change ride characteristics.

Product Features:

Made of Superior Hyper-Flex+ Material
Lasts from 3 to 10 Times Longer
Assemble to Chassis Same Way as OEM
Maintains Factory Ride Characteristics
Simple Way to Increase Vehicle Height

from

$127.99

What better way to check you oil level by using one of B&M’s transmission fluid dipsticks? The cap screws into the tube and is O-ring sealed, while the base of the tube has a sealing grommet where it goes into the transmission.

Product Features:

Automatic Transmission Dip Stick

from

$173.99

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1955-85 GM small block (internally balanced) V8 engines along with 4.3L V6 engines. Also fits 1990 and earlier GM big block (internally balanced) V8 engines with two piece rear main seal. Features include high tensile strength steel construction to resist elongation and cracking, dual bolt pattern 10.75 or 11.5 inch converter mounting locations, 168 tooth ring gear with double-sided welds for added strength and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953. Compatible with Powerglide, TH350, TH400 and TH700R4 automatic transmissions.

Product Features:

NHRA/IHRA Legal For All Classes
Includes SFI Certification Sticker
Ideal For Street Applications
To Extreme Duty Racing
To High RPM Use

from

$19.99

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. Designed to operate with all synthetic, conventional, and blended motor oils, K&N’s pleated synthetic-blend filtration media helps to shield your engine from contaminants and ensure a consistent flow of oil. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers, and is protected by the K&N 1-Year Limited Warranty.

Product Features:

Designed to allow high flow rates and a consistent flow of oil to your engine
Pleated synthetic-blend filtration media removes most harmful contaminants
Fast and easy Wrench-Off removal using the welded one-inch hex nut
High capacity to withstand the service intervals recommended by vehicle manufacturers
Heavy-duty canister for outstanding durability
Laboratory tested to ensure excellent capacity, efficiency, and mechanical strength
Designed to operate with all synthetic, conventional, and blended motor oils
1-Year Limited Warranty

from

$32.99

Edelbrock part #7246 Intake Gaskets for 1967-1976 400-455 Buick allow for optimum flow and performance. Any gasket can create a seal, but a good gasket can do it with less clamping force, and for a longer period of time. The new MP-2N Micropore technology

Product Features:

1.15″x2.38″
Features Embossed Silicone Bead Around The Intake Ports & Water Openings
.032″ Thick
Two Piece Configuration
End Seals Not Included

from

$337.99

Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer

from

$32.49

Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:

Complete with o-rings and mounting bolts
Features an o-ring style seal to prevent water leaks
Chrome plated
1/2″ NPT port can be used for various coolant temp related sensors or switches

from

$167.99

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$767.99

Matched assembly for maximum reliability. An excellent choice for high performance street applications.

Product Features:

Built As Matched Assembly
Exceptional Performance
Exceptional Durability
Long Term Dependability
Designed for Street And Street Strip Applications

from

$55.99

If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.

Product Features:

Improved output coil for electronic ignitions
Works w/Blaster Ignition Or MSD 5/6/7 Series
Ballast Resistor Required If Used w/Stock Points Ignition
Alkyd tower w/high dielectric properties lessens carbon tracking

from

$204.99

Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).

Product Features:

Glass Filled Polyester Case
Longer Spark Duration
Increased Performance
No Energy Loss Due To Arcing
Includes Brass Contact Terminal

from

$37.99

The Edelbrock valve cover gaskets #7546?provide excellent sealing integrity and conformability for easy installation. The multi-layer construction has two highly compressible, high rubber content, fiber-reinforced outside layers which are chemically bonde

Product Features:

0.1875 in. Thickness
Core-Reinforced-Composite Material
For Buick 400-455
Set of 2
Made In The USA

Upgrade your 1969 Buick Wildcat with Top-Quality Performance and Racing Products

When it comes to maintaining or upgrading your 1969 Buick Wildcat, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Buick or enhancing its overall performance, Performance and Racing Products are key to keeping your Wildcat functioning at its best. At Advance Auto Parts, we offer a wide selection of 67 Performance and Racing Products for the 1969 Buick Wildcat, designed to meet your needs without breaking the bank. From Performance Fuel System replacements to Performance Oil Filters upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1969 Buick Wildcat at great prices. Our Performance and Racing Products inventory for this model ranges from just $5.99 to $972.99, with an average price of $287.49. Our 67 Performance and Racing Products in stock come from 16 trusted brands, so you’re sure to find the right part for your 1969 Buick Wildcat without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1969 Buick Wildcat, we stock popular OEM and aftermarket Performance and Racing Products from top names like Holley, B & M, Accel, and more. Holley Performance and Racing Products start at just $509.99 and boast an impressive 4.2 stars average rating from customers. B & M and Accel also bring quality to the table, with Performance and Racing Products available starting at $53.99, and at an average 4.1 stars rating. With 234 customer reviews and counting, our 1969 Buick Wildcat Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1969 Buick Wildcat is always ready to roll. We’re committed to providing you with everything you need to keep your Wildcat in top shape, all in one place. Start shopping confidently below for your 1969 Buick Wildcat!

Best-Selling Performance Fuel Systems for 1969 Buick Wildcats

Enhance the driving experience in your Buick with 4 quality Performance Fuel System components, starting at $509.99.

show more show less

from

$509.99

Holley’s new 0-80457SA is constructed from aluminum which compared to its zinc counterpart equates to a weight savings of 40%! Holley’s aluminum 0-80457SA will hold its shine longer and also can be hand polished for a custom look! Its 600 CFM of airflow,

Product Features:

Vibratory Polished For Good Looks

from

$716.99

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

Vibratory Polished For Good Looks
Optimized Street Calibration That Works Out Of The Box
Factory Preset Electric Choke For Easy Startups
Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
No Unnecessary Trips Back To The Parts Store
Limited Lifetime Warranty
100% Wet Flow Tested By Holley Technicians
Arrives Ready To Run

from

$699.99

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

Vibratory Polished For Good Looks
Optimized Street Calibration That Works Out Of The Box
Factory Preset Electric Choke For Easy Startups
Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
No Unnecessary Trips Back To The Parts Store
Limited Lifetime Warranty
100% Wet Flow Tested By Holley Technicians
Arrives Ready To Run

from

$819.99

The off-road truck avenger is designed specifically for off-road applications. The unique fuel metering block eliminates fuel spillover through the boosters at extreme angles allowing for 40 degree climbing, 30 degree side hill maneuvers and nose-down descents to avoid hesitations, stalling and flooding typically associated with carbs in an off road environment. The 470 CFM off-road truck avenger is the perfect carburetor for 4 cylinder, V-6, and inline 6 cylinder engines. Viton(R) is a registered trademark of DuPont Performance Elastomers.

Product Features:

Gold Dichromate Finish For Extreme Off Road Environments
Single Feed Fuel Inlet For Ease Of Installation
Optimized Off-Road Calibration That Works Out-Of-The-Box
Factory Preset Electric Choke For Easy Startups
Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
One Piece Off-Road Vent Tube Eliminates Fuel Spillover
Metering Block For Flood Free Op. 40 deg. Climb/30 deg. Side Hill
Limited Lifetime Warranty Defects In Material/Workmanship

Top Picks for 1969 Buick Wildcat Performance Air Filters

Upgrade Buick Wildcats with top-quality Performance Air Filters parts, including 1 OEM and aftermarket selections for your 1969 model.

show more show less

from

$31.99

Replacement for 14 inch by 3 inch round air filter
Fits perfectly in your vehicle’s air box as a replacement for your factory air filter
Engineered for increased flow and greater performance
Fits select Buick, Cadillac, Chevy, GM, Mercedes, Oldsmobile and Pontiac models
Factory pre-oiled and ready to use
Simple installation

In-Demand Performance Exhaust Products for 1969 Buick Wildcats

Select from 2 premium Performance Exhaust Products parts for your 1969 Buick Wildcat, with prices ranging from $34.49 to $34.99.

show more show less

from

$34.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

from

$34.99

Edelbrock part No. 7247 Exhaust Gaskets are designed for 1967-76 Buick 400-455 V8 engines. These Exhaust Gaskets are made of EnCore HTX-900

Most Sold 1969 Buick Wildcat Performance Engines

Explore our best-selling Buick parts for the 1969 Wildcat among 18 OEM and aftermarket options starting from $13.99.

show more show less

from

$33.99

Work with .530″ guides and 3/8″ valve stem diameter
Valve stem oil seals keep unwanted oil from entering the combustion chamber
Several different types of valve seals are offered

from

$562.99

Torque Converter – Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New allow steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required.

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer
Washer Between Turbine and Cover

from

$32.49

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 195 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$32.49

Complete with o-rings and mounting bolts
Features an o-ring style seal to prevent water leaks
Chrome plated
1/2″ NPT port can be used for various coolant temp related sensors or switches

from

$37.99

0.1875 in. Thickness
Core-Reinforced-Composite Material
For Buick 400-455
Set of 2
Made In The USA

from

$337.99

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer

from

$32.99

1.15″x2.38″
Features Embossed Silicone Bead Around The Intake Ports & Water Openings
.032″ Thick
Two Piece Configuration
End Seals Not Included

from

$972.99

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine
Dual Pattern Drive Lugs
New Turbine Hub
New Springs/Rollers In Stator

from

$921.99

HoleShot 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$562.99

HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) Application: HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

High Energy 218/218 Hydraulic Flat Cam for Buick 400, 430, 455

from

$504.99

High Energy 218/218 Hydraulic Flat Cam for Buick 400, 430, 455

from

$422.99

16 Springs

from

$166.99

Engine Valve Spring Kit

from

$149.99

Product Features:

Non-Rotator Type
1.550 in. Outer Diameter
.190 Wire Size
Single Coil Spring Type
Set of 16

from

$109.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions.

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printo seal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$71.99

GASKETS

High Energy 9.378" Long, 5/16" Diameter Pushrod Set

from

$49.99

High Energy 9.378" Long, 5/16" Diameter Pushrod Set

High Energy Hydraulic Flat Lifter for Buick 181-252/350-455 and Cadillac 472-500

from

$13.99

High Energy Hydraulic Flat Lifter for Buick 181-252/350-455 and Cadillac 472-500

Top-Rated Performance and Racing Products Brands For Your 1969 Buick Wildcat

Shop for the best-rated brands offering Performance and Racing Products and other products for your 1969 Buick Wildcats. Below you’ll find some of our best rated Performance and Racing Products from Holley, B & M, and Accel, and more. Performance and Racing Products from these brands that fit a 1969 Wildcat start at just $53.99 and are rated as high as 4.2 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.

Popular Holley 1969 Buick Wildcat Performance and Racing Products

When it comes to maintaining or upgrading your 1969 Buick Wildcat, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. Holley ticks all of those boxes. We offer a wide selection of Holley Performance and Racing Products, specifically designed for the 1969 Buick Wildcat. With over 3 Holley brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $509.99, with an average price of just $642.32. Plus, with over 53 customer reviews and an average rating of 4.2 stars, you can trust that our Holley Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from $716.99

(2)

Prem Street Carbs (Avengers)

“This was the carb that my engine builder suggested.”

from $699.99

(6)

Street Carburetor: 670 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny

“great carb”

from $509.99

(45)

Street Carburetor: 600 CFM, Electric Choke, 4 Barrel, Square Bore, Single Inlet, Shiny

“very easy to install…replaced older carb this one is fresh and runs smooth … needed to do minor ajustment .. but nothing anyone couldn’t do …”

Popular B & M 1969 Buick Wildcat Performance and Racing Products

B & M auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1969 Buick Wildcat owner should feel confident when installing genuine B & M parts in their vehicle. To ensure the best fit and performance for your 1969 Wildcat, Advance Auto Parts carries a full inventory of 3 B & M Performance and Racing Products. Plus you will be keeping your Buick in peak condition while saving money because prices on these B & M Performance and Racing Products range from $371.99 to $562.99, plus, with more than 3 customer reviews and an impressive 4.1 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.

from $539.99

(1)

Automatic Shifter – Megashifter – Universal

“its was pretty easy to install if u have any type of knowlegde of cars it should not be difficult at all and the shifting is awesome just be careful w”

from $371.99

(1)

Automatic Shifter, Sport Shifter

“This is a sweetly made product with that hotrod look and feel.This shifter was easy to install and a knock out to drive.No down falls as far as I’m aw”

from $562.99

(1)

Tork Master 3000

“good parts and very strong”

FAQs for 1969 Buick Wildcat Performance and Racing Products

Which Performance and Racing Products are best-sellers for 1969 Buick Wildcats?

Out of 67 Performance and Racing Products that fit 1969 Buick Wildcats, the following parts are the top sellers:

Premium Oil Filter: Ideal for Synthetic, Conventional & Blended Oil, Protects Your Engine (6120011) – $19.99
Tie Rod Dust Boot (17360821) – $5.99
Tie Rod Dust Boot (17360833) – $5.99

What’s the price range for 1969 Buick Wildcat Performance and Racing Products?

Performance and Racing Product prices for the 1969 Buick Wildcat start at $5.99 and go up to $972.99 for the most premium parts.

What’s the average price of a Performance and Racing Product for a 1969 Buick Wildcat?

The average price for Performance and Racing Products for the 1969 Buick Wildcat is $287.49. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Performance and Racing Products for other Buick Wildcat model years?

Yes, we currently carry Performance and Racing Products for 7 model years of Buick Wildcats between 1962 and 1970. Performance and Racing Products are bought most frequently for the following model years: 1970, 1968, 1967, 1966, 1965, 1964, 1963, and 1962.

What are the cheapest Performance and Racing Products for my 1969 Buick Wildcat?

The cheapest 1969 Buick Wildcat Performance and Racing Products we carry in stock are:

Tie Rod Dust Boot (17360821) – $5.99
Tie Rod Dust Boot (17360833) – $5.99
Tie Rod Dust Boot (22906873) – $6.29
Coil Spring Isolator Set (22908204) – $13.29
Coil Spring Isolator Set (22908205) – $13.29

What are the top-rated Performance and Racing Products that fit the 1969 Buick Wildcat?

Out of 234 reviews by customers, our 1969 Buick Wildcat Performance and Racing Products have an average customer rating of . These are some of the highest-rated Performance and Racing Product types for the 1969 Buick Wildcat and their top-rated products:

Performance Shifters
- Automatic Shifter – Megashifter – Universal (6900895) – $539.99
- Automatic Shifter, StarShifter (6274609) – $349.99
- Automatic Shifter, Sport Shifter (17130066) – $371.99
Performance Oil Filters
- Automatic Shifter – Megashifter – Universal (6900895) – $539.99
- Automatic Shifter, StarShifter (6274609) – $349.99
- Automatic Shifter, Sport Shifter (17130066) – $371.99

What types of Performance and Racing Products do you sell for my 1969 Buick Wildcat?

As of 3/1/26, these are some of the most in-demand types of Performance and Racing Products for a 1969 Buick Wildcat:

Can I get help with 1969 Buick Wildcat Performance and Racing Product orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Buick Performance and Racing Products and more.

What is your return policy for Buick Wildcat Performance and Racing Products?

Advance Auto Parts keeps returns simple. For new Buick Wildcat Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1969 Buick Wildcat Performance and Racing Products

Energy Suspension – Tie Rod Dust Boot (Part No.9.13101R)

Mallory – Unilite Breakerless Ignition Conversion Kit (Part No.503M)

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1479)

Richmond Gear – RngPnn (Part No.49-0015-1)

B & M – Automatic Shifter, Street Bandit Shifter (Part No.80797)

Mallory – Distributor Wiring Harness (Part No.29349)

Accel – Distributor Cap And Rotor Kit (Part No.8120)

Energy Suspension – Control Arm Bushing Set (Part No.3.3132G)

B & M – Transkit For 65-87 TH400 Transmission (Part No.20229)

Edelbrock – Sure Seat Valve Springs for Chrysler 383-400-413-440 V8 1969-79 (Part No.5792)

Competition Cams – VALVE SEALS, TEFLON 3/8" 1 ST (Part No.505-16)

Spectre – Spectre Replacement Air Filter (Part No.HPR0136)

Holley – Street Carburetor: 670 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny (Part No.0-80670)

Mallory – Distributor Condenser (Part No.401)

Energy Suspension – Coil Spring Isolator Set (Part No.3.6108R)

B & M – Aluminum Braided Dip Stick, Fits TH-400 Transmission (Part No.22166)

B & M – Flexplate, SFI 29.1 Approved, Fits 168-Tooth, 2-Piece Rear Main Seal, Chevy V8 (Part No.20230)

K&N – Premium Oil Filter: Ideal for Synthetic, Conventional & Blended Oil, Protects Your Engine (Part No.HP-2003)

Edelbrock – Intake Manifold Gasket for 1967-1976 400-455 Buick (Part No.7246)

B & M – Performance Torque Converter for GM TH400, 350, & 375 Transmissions (Part No.20400)

Mr. Gasket – Water Neck (Part No.2557)

Energy Suspension – Control Arm Bushing Set (Part No.3.3132R)

Hays – Power Train (Part No.85-110)

MSD Ignition – Blaster 2 Coil: High Performance Ignition Upgrade (Part No.8202)

Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)

Edelbrock – Valve Cover Gasket Set for Buick (Part No.7546)

Holley – Street Carburetor: 600 CFM, Electric Choke, 4 Barrel, Square Bore, Single Inlet, Shiny (Part No.0-80457S)

Holley – Prem Street Carbs (Avengers) (Part No.0-80770)

Holley – Street Carburetor: 670 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny (Part No.0-80670)

Holley – Off Road Carbs (Part No.0-90670)

K&N – Premium Oil Filter: Ideal for Synthetic, Conventional & Blended Oil, Protects Your Engine (Part No.HP-2003)

Spectre – Spectre Replacement Air Filter (Part No.HPR0136)

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1479)

Edelbrock – Exhaust Manifold Gasket Set for Buick (Part No.7247)

Competition Cams – VALVE SEALS, TEFLON 3/8" 1 ST (Part No.505-16)

B & M – Tork Master 3000 (Part No.20402)

Mr. Gasket – High Performance Thermostat (Part No.4365)

Mr. Gasket – Water Neck (Part No.2557)

Edelbrock – Valve Cover Gasket Set for Buick (Part No.7546)

B & M – Performance Torque Converter for GM TH400, 350, & 375 Transmissions (Part No.20400)

Edelbrock – Intake Manifold Gasket for 1967-1976 400-455 Buick (Part No.7246)

B & M – Holeshot 3600 (Part No.20425)

B & M – Holeshot 3000 (Part No.20413)

B & M – Holeshot 2400 (Part No.20412)

Competition Cams – High Energy 218/218 Hydraulic Flat Cam for Buick 400, 430, 455 (Part No.96-203-4)

Competition Cams – 16 Springs (Part No.26120-16)

Competition Cams – Engine Valve Spring Kit (Part No.910-16)

Edelbrock – Sure Seat Valve Springs for Chrysler 383-400-413-440 V8 1969-79 (Part No.5792)

FEL-PRO Performance – Performance Cylinder Head Gasket (Part No.1125)

Edelbrock – GASKETS (Part No.7346)

Competition Cams – High Energy 9.378" Long, 5/16" Diameter Pushrod Set (Part No.7896-16)

Competition Cams – High Energy Hydraulic Flat Lifter for Buick 181-252/350-455 and Cadillac 472-500 (Part No.869-1)