1969 Buick GS 350 Performance and Racing Products

Essential Performance and Racing Products for 1969 Buick GS 350s

Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)

Promaster Classic Series; Ignition Coil

from

$186.99
Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).

Product Features:
  • Glass Filled Polyester Case
  • Longer Spark Duration
  • Increased Performance
  • No Energy Loss Due To Arcing
  • Includes Brass Contact Terminal
See More

Hays – Power Train (Part No.85-103)

Power Train

from

$530.99
High burst strength woven lining to withstand heat and higher engine RPM. Heavy-duty sprung hub assembly to allow smooth engagement and steady torque transfer without chatter. Recommended for high horsepower street vehicles in addition to occasional drag strip use.

Product Features:
  • Built As Matched Assembly
  • Exceptional Performance
  • Exceptional Durability
  • Long Term Dependability
See More

Mr. Gasket – Alternator Bracket (Part No.9850)

Alternator Bracket

from

$25.99
Hold your alternator securely in place with Mr. Gasket chrome alternator bracket. Chrome plated heavy gauge steel for long lasting good looks. Must be used with #9852.

Product Features:
  • Chrome Plated Steel
  • F-Style
  • Heavy Gauge Steel Construction
  • Fits Small Block Chevy 265-400 CID
  • Must Be Used With Part 9852
See More

Mallory – Unilite Breakerless Ignition Conversion Kit (Part No.503M)

Unilite Breakerless Ignition Conversion Kit

from

$176.99
Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:
  • Easy Installation
  • Improved Fuel Economy
  • Reduced Maintenance
  • Accurate Timing
  • Improved Performance
  • Provides A Simple Conversion
  • No Moving Parts To Wear Out
See More

Flowmaster Inc. – 40 Series Muffler, 2in Offset Inlet 2in Offset Outlet, Non-Reversible, Aggressive Sound (Part No.942043)

40 Series Muffler, 2in Offset Inlet 2in Offset Outlet, Non-Reversible, Aggressive Sound

from

$133.99
This two chamber design incorporates Flowmaster’s patented Delta Flow technology. The Delta deflectors generate increased scavenging for better performance and reduced interior sound. Milder exterior tone and reduced interior resonance over Original 40 series. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More

Edelbrock – Performer RPM Carb/Plate Nitrous Systems 4500 Series Carbs (100-150-250 Hp) (Part No.70053)

Performer RPM Carb/Plate Nitrous Systems 4500 Series Carbs (100-150-250 Hp)

from

$757.99


Product Features:
  • Designed For Carbureted V8 Engines
  • Simple To Install
See More

Mr. Gasket – Thermocap Radiator Cap (Part No.2476BK)

Thermocap Radiator Cap

from

$48.09
The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:
  • Indicates coolant temperature
  • Helps prevent coolant injuries
  • Fahrenheit and centigrade readings
  • Color-coded temperature ranges
  • Integrated coolant reclamation valve
  • Improves under-hood appearance
  • Chromed crown with a colored trim ring
See More

MSD Ignition – Distributor; Buick V8 215-350 Pro-Billet (Part No.8548)

Distributor; Buick V8 215-350 Pro-Billet

from

$593.99
MSD Pro-Billet Distributors are the finest performance and racing distributors available. Every feature has been engineered to endure the rigors of high performance and racing engines. Whether cruising the streets or racing stock cars, dragsters, boats or trucks, MSD has a distributor for it. MSD uses state-of-the-art, Computer Numerical Controlled (CNC) mills and lathes to machine each housing. After a long series of precise cuts and movements, the billet is formed into a flawless distributor housing that is accurate to within 0.001″. The flex-free housings are lightweight, have no porosity or weak areas and look great on polished, show quality engines.

Product Features:
  • CNC machined billet aluminum housing and billet aluminum base
  • Must Be Used w/An MSD Ignition Control
  • Supplied w/HEI style distributor cap/rotor (accepts Cap-A-Dapts)
  • Mech. advance assem. can be locked out for crank trigger systems
  • Advance plate and weights are fine blanked from chrome moly steel
  • QPQ coated for friction reduction
  • QPQ coated polished steel shaft; guided by sealed ball bearings
  • Easy-to-adjust mech. advance w/supplied springs and stop bushings
See More

Mallory – Unilite Ignition Module (Part No.605)

Unilite Ignition Module

from

$85.29
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:
  • Service Part
  • No Moving Parts To Wear Out
  • Self Contained Unit
  • Can Drive OEM
  • Can Drive High Performance Ignition Coils
See More

Edelbrock – CARBURETOR (Part No.14054)

CARBURETOR

from

$488.99
Product Features:
  • EnduraShine Finish
  • GM/AMC-Style Throttle Linkage
  • Can Add Electric Choke PN[1478]
  • Easy Tuning with 2-Piece Design
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Powertrax – Lock Right Locker (Part No.1910-LR)

Lock Right Locker

from

$376.99
The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.
  • Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.
  • Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.
  • Powertrax® = Extreme Traction Systems!
  • See More

    Mr. Gasket – Water Neck (Part No.2557)

    Water Neck

    from

    $27.49
    Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

    Product Features:
    • Complete with o-rings and mounting bolts
    • Features an o-ring style seal to prevent water leaks
    • Chrome plated
    • 1/2″ NPT port can be used for various coolant temp related sensors or switches
    See More

    Accel – Distributor Cap And Rotor Kit (Part No.8124)

    Distributor Cap And Rotor Kit

    from

    $48.49


    Product Features:
    • Heavy Duty Cap and Rotor Kit
    • With Brass Inserts
    See More

    Edelbrock – Performer RPM 2 Carb/Plate Nitrous Systems Square-Bore Carbs (100-400+ Hp) (Part No.70082)

    Performer RPM 2 Carb/Plate Nitrous Systems Square-Bore Carbs (100-400+ Hp)

    from

    $1114.99


    Product Features:
    • Designed For Carbureted V8 Engines
    • Enhanced Flow Capacity
    • Add Power In Stages
    • Softens The Hit Of The Nitrous System
    See More

    Edelbrock – Performer RPM Carb/Plate Nitrous Systems Square-Bore Carbs (100-250 Hp) (Part No.70090)

    Performer RPM Carb/Plate Nitrous Systems Square-Bore Carbs (100-250 Hp)

    from

    $875.99


    Product Features:
    • Designed For Carbureted V8s
    • Power Increases From 100-250 HP
    • Precision EDM Machined Spray Bars
    • Simple To Install
    See More

    Earls Performance Product – Brake Bleeder Screws (Part No.280029ERL)

    Brake Bleeder Screws

    from

    $40.99
    Brake Bleeder Screws

    B & M – Automatic Shifter, Quicksilver 4 Speed (Part No.80683)

    Automatic Shifter, Quicksilver 4 Speed

    from

    $439.99
    The B&M Quicksilver features a ratcheting action for positive shifts, Chrome Knob, neutral safety switch, NHRA/IHRA approved Reverse Lockout. Fits Most 3 and 4 speeds.

    Product Features:
    • Universal Floor Mount Application
    • Base Trimmed For Custom Fit
    • Cable Operated
    • Quick Installation
    • Accurate Shifting
    See More

    B & M – Automatic Shifter, Hammer Shifter, Universal (Part No.80885)

    Automatic Shifter, Hammer Shifter, Universal

    from

    $339.99
    The Hammer shifter may just be the most comfortable and versatile shifter available. The unique design of the shift handle easily fits all sizes of hands providing the appropriate wrist angle and feel when shifting. The multi-position lockout trigger is s

    Product Features:
    • Ratchet Action Shifter
    • Cable Operated
    • Quick Installation
    • Accurate Shifting
    • Reverse Lockout Feature
    See More

    Richmond Gear – Differential Ring And Pinion (Part No.69-0378-1)

    Differential Ring And Pinion

    from

    $348.99
    Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

    Product Features:
    • For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
    • The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
    • Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
    • Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
    • Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.
    See More

    Richmond Gear – RngPnn (Part No.69-0304-1)

    RngPnn

    from

    $342.99
    RngPnn

    Mallory – Distributor Condenser (Part No.401)

    Distributor Condenser

    from

    $17.09
    Distributor Condenser

    FAG US – CUP (Part No.LM48510)

    CUP

    from

    $7.69
    CUP

    Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

    High Performance 180 Degree Thermostat for Increased Flow

    from

    $26.99
    Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

    Product Features:
    • Opens At 180 Degrees
    • Designed to Resist Large Variations of Coolant Pressure at High RPM
    • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
    • For High Performance Street, Drag Race, and Oval Track
    • Copper & Brass Construction – Resists Corrosion
    • High Flow
    See More

    Upgrade your 1969 Buick GS 350 with Top-Quality Performance and Racing Products

    When it comes to maintaining or upgrading your 1969 Buick GS 350, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Buick or enhancing its overall performance, Performance and Racing Products are key to keeping your GS 350 functioning at its best. At Advance Auto Parts, we offer a wide selection of 57 Performance and Racing Products for the 1969 Buick GS 350, designed to meet your needs without breaking the bank. From Performance Fuel System replacements to Performance Distributors upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

    Affordable Prices and Wide Selection

    Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1969 Buick GS 350 at great prices. Our Performance and Racing Products inventory for this model ranges from just $7.69 to $1,138.99, with an average price of $396.98. Our 57 Performance and Racing Products in stock come from 14 trusted brands, so you’re sure to find the right part for your 1969 Buick GS 350 without overspending.

    Top Brands and High Customer Satisfaction

    Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1969 Buick GS 350, we stock popular OEM and aftermarket Performance and Racing Products from top names like Mallory, Mr. Gasket, Accel, and more. Mallory Performance and Racing Products start at just $17.09 and boast an impressive 5 stars average rating from customers. Mr. Gasket and Accel also bring quality to the table, with Performance and Racing Products available starting at $25.99, and at an average 4 stars rating. With 50 customer reviews and counting, our 1969 Buick GS 350 Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.

    Explore Related Parts and More

    While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1969 Buick GS 350 is always ready to roll. We’re committed to providing you with everything you need to keep your GS 350 in top shape, all in one place. Start shopping confidently below for your 1969 Buick GS 350!

    Best-Selling Performance Fuel Systems for 1969 Buick GS 350s

    Enhance the driving experience in your Buick with 4 quality Performance Fuel System components, starting at $407.99.

    Edelbrock – CARBURETOR (Part No.14054)

    CARBURETOR

    from

    $488.99
    Product Features:
    • EnduraShine Finish
    • GM/AMC-Style Throttle Linkage
    • Can Add Electric Choke PN[1478]
    • Easy Tuning with 2-Piece Design
    • Smooth Secondary Transition
    • Both Timed and Full Vacuum Ports
    • Includes PCV Outlet
    See More

    Edelbrock – Performer 1400 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1400)

    Performer 1400 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet

    from

    $498.99
    The Edelbrock 1400 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characterist

    Product Features:
    • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
    • Electric Choke
    • 4 Barrel Count
    • Square Bore
    • Electric Choke Installed from Factory
    • Smooth Secondary Transition
    • Includes Only Timed Vacuum Port
    • Includes EGR ; Fuel Vapor Outlet
    See More

    Edelbrock – Thunder AVS Carburetor #1826 650 CFM With Electric Choke, Satin Finish (Non-EGR) (Part No.1826)

    Thunder AVS Carburetor #1826 650 CFM With Electric Choke, Satin Finish (Non-EGR)

    from

    $464.99
    New or reconditioned 650cfm. Square-flange. Electric choke without EGR. Primary jet 0.095. Secondary jet 0.098. Metering Rod 0.065 x 0.047. Dual plane intake. Spring loaded needles and seat increase performance. New qwik-tune adjustable secondary air valve. Distinctive black accented hardware. Lightweight ball burnished aluminum. No gaskets below fuel level to prevent leakage. Metering rod and step up springs can be changed easily. GM and AMC style throttle linkage.

    Product Features:
    • Spring Loaded Needles/Seat Increase Performance
    • New Qwik-Tune Adjustable Secondary Air Valve
    • Distinctive Black Accented Hardware
    • Lightweight Ball-Burnished Aluminum
    • No Gaskets Below Fuel Level to Prevent Leakage
    • Metering Rod/Step Up Springs Can Be Changed Easily
    • GM/AMC-Style Throttle Linkage
    See More

    Edelbrock – Performer Carburetor #9907 750 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.9907)

    Performer Carburetor #9907 750 CFM With Manual Choke, Satin Finish (Non-EGR)

    from

    $407.99
    Product Features:
    • Satin Finish
    • 4 Barrel
    • Annular Booster Type
    • Manual Choke Type
    • 750 cfm Maximum Flow Rating
    See More

    Most Popular 1969 Buick GS 350 Performance Distributors

    Customize your Buick with 2 Performance Distributors products like Performance Distributor Cap and Rotor Kits and Performance Distributors, all priced under $593.99.

    Accel – Distributor Cap And Rotor Kit (Part No.8124)

    Distributor Cap And Rotor Kit

    from

    $48.49


    Product Features:
    • Heavy Duty Cap and Rotor Kit
    • With Brass Inserts
    See More

    MSD Ignition – Distributor; Buick V8 215-350 Pro-Billet (Part No.8548)

    Distributor; Buick V8 215-350 Pro-Billet

    from

    $593.99
    MSD Pro-Billet Distributors are the finest performance and racing distributors available. Every feature has been engineered to endure the rigors of high performance and racing engines. Whether cruising the streets or racing stock cars, dragsters, boats or trucks, MSD has a distributor for it. MSD uses state-of-the-art, Computer Numerical Controlled (CNC) mills and lathes to machine each housing. After a long series of precise cuts and movements, the billet is formed into a flawless distributor housing that is accurate to within 0.001″. The flex-free housings are lightweight, have no porosity or weak areas and look great on polished, show quality engines.

    Product Features:
    • CNC machined billet aluminum housing and billet aluminum base
    • Must Be Used w/An MSD Ignition Control
    • Supplied w/HEI style distributor cap/rotor (accepts Cap-A-Dapts)
    • Mech. advance assem. can be locked out for crank trigger systems
    • Advance plate and weights are fine blanked from chrome moly steel
    • QPQ coated for friction reduction
    • QPQ coated polished steel shaft; guided by sealed ball bearings
    • Easy-to-adjust mech. advance w/supplied springs and stop bushings
    See More

    Top Picks for 1969 Buick GS 350 Performance Engines

    Upgrade Buick GS 350s with top-quality Performance Engines parts, including 2 OEM and aftermarket selections for your 1969 model.

    Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

    High Performance 180 Degree Thermostat for Increased Flow

    from

    $26.99
    Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

    Product Features:
    • Opens At 180 Degrees
    • Designed to Resist Large Variations of Coolant Pressure at High RPM
    • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
    • For High Performance Street, Drag Race, and Oval Track
    • Copper & Brass Construction – Resists Corrosion
    • High Flow
    See More

    Mr. Gasket – Water Neck (Part No.2557)

    Water Neck

    from

    $27.49
    Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

    Product Features:
    • Complete with o-rings and mounting bolts
    • Features an o-ring style seal to prevent water leaks
    • Chrome plated
    • 1/2″ NPT port can be used for various coolant temp related sensors or switches
    See More

    In-Demand Performance Ignition Products for 1969 Buick GS 350s

    Select from 8 premium Performance Ignition Products parts for your 1969 Buick GS 350, with prices ranging from $17.09 to $186.99.

    Mallory – Unilite Ignition Module (Part No.605)

    Unilite Ignition Module

    from

    $85.29
    Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

    Product Features:
    • Service Part
    • No Moving Parts To Wear Out
    • Self Contained Unit
    • Can Drive OEM
    • Can Drive High Performance Ignition Coils
    See More

    Mallory – Mallory Kit: Unil Conv: Delco: V8 (Part No.501)

    Mallory Kit: Unil Conv: Delco: V8

    from

    $134.99
    Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

    Product Features:
    • Easy Installation
    • Improved Fuel Economy
    • Reduced Maintenance
    • Accurate Timing
    • Improved Performance
    • Provides A Simple Conversion
    • No Moving Parts To Wear Out
    See More

    MSD Ignition – Blaster 2 Coil: High Performance Ignition Upgrade (Part No.8202)

    Blaster 2 Coil: High Performance Ignition Upgrade

    from

    $49.99
    If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.

    Product Features:
    • Improved output coil for electronic ignitions
    • Works w/Blaster Ignition Or MSD 5/6/7 Series
    • Ballast Resistor Required If Used w/Stock Points Ignition
    • Alkyd tower w/high dielectric properties lessens carbon tracking
    See More

    Accel – Supercoil (Part No.140001)

    Supercoil

    from

    $105.99
    Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

    Product Features:
    • Oil Filled For Better Cooling
    • Optimized Low Resistance
    • Silicon Magnetic Steel E-Core
    • Higher Energy/Voltage Outputs
    • Quicker Starts
    • Improved Idle Quality
    • Resists Shock And Vibration
    • Resists Corrosion
    See More

    Mallory – Distributor Wiring Harness (Part No.29349)

    Distributor Wiring Harness

    from

    $30.49


    Product Features:
    • Service Part
    • Makes Connections Quick And Easy
    See More

    Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)

    Promaster Classic Series; Ignition Coil

    from

    $186.99
    Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).

    Product Features:
    • Glass Filled Polyester Case
    • Longer Spark Duration
    • Increased Performance
    • No Energy Loss Due To Arcing
    • Includes Brass Contact Terminal
    See More

    Mallory – Unilite Breakerless Ignition Conversion Kit (Part No.503M)

    Unilite Breakerless Ignition Conversion Kit

    from

    $176.99
    Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

    Product Features:
    • Easy Installation
    • Improved Fuel Economy
    • Reduced Maintenance
    • Accurate Timing
    • Improved Performance
    • Provides A Simple Conversion
    • No Moving Parts To Wear Out
    See More

    Mallory – Distributor Condenser (Part No.401)

    Distributor Condenser

    from

    $17.09
    Distributor Condenser

    Most Sold 1969 Buick GS 350 Performance Exhaust Products

    Explore our best-selling Buick parts for the 1969 GS 350 among 2 OEM and aftermarket options starting from $25.99.

    Mr. Gasket – Alternator Bracket (Part No.9850)

    Alternator Bracket

    from

    $25.99
    Hold your alternator securely in place with Mr. Gasket chrome alternator bracket. Chrome plated heavy gauge steel for long lasting good looks. Must be used with #9852.

    Product Features:
    • Chrome Plated Steel
    • F-Style
    • Heavy Gauge Steel Construction
    • Fits Small Block Chevy 265-400 CID
    • Must Be Used With Part 9852
    See More

    Flowmaster Inc. – 40 Series Muffler, 2in Offset Inlet 2in Offset Outlet, Non-Reversible, Aggressive Sound (Part No.942043)

    40 Series Muffler, 2in Offset Inlet 2in Offset Outlet, Non-Reversible, Aggressive Sound

    from

    $133.99
    This two chamber design incorporates Flowmaster’s patented Delta Flow technology. The Delta deflectors generate increased scavenging for better performance and reduced interior sound. Milder exterior tone and reduced interior resonance over Original 40 series. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
    See More

    Top-Rated Performance and Racing Products Brands For Your 1969 Buick GS 350

    Shop for the best-rated brands offering Performance and Racing Products and other products for your 1969 Buick GS 350s. Below you’ll find some of our best rated Performance and Racing Products from Mallory, Mr. Gasket, and Accel, and more. Performance and Racing Products from these brands that fit a 1969 GS 350 start at just $17.09 and are rated as high as 5 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.

    Popular Mallory 1969 Buick GS 350 Performance and Racing Products

    When it comes to maintaining or upgrading your 1969 Buick GS 350, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. Mallory ticks all of those boxes. We offer a wide selection of Mallory Performance and Racing Products, specifically designed for the 1969 Buick GS 350. With over 6 Mallory brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $17.09, with an average price of just $105.31. Plus, with over 4 customer reviews and an average rating of 5 stars, you can trust that our Mallory Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

    Distributor Wiring Harness
    from
    $30.49
    This product is not rated

    Distributor Wiring Harness

    “”

    Unilite Breakerless Ignition Conversion Kit
    from
    $176.99
    This product is not rated

    Unilite Breakerless Ignition Conversion Kit

    “”

    Promaster Classic Series; Ignition Coil
    from
    $186.99
    This product is not rated

    Promaster Classic Series; Ignition Coil

    “”

    Popular Mr. Gasket 1969 Buick GS 350 Performance and Racing Products

    Mr. Gasket auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1969 Buick GS 350 owner should feel confident when installing genuine Mr. Gasket parts in their vehicle. To ensure the best fit and performance for your 1969 GS 350, Advance Auto Parts carries a full inventory of 4 Mr. Gasket Performance and Racing Products. Plus you will be keeping your Buick in peak condition while saving money because prices on these Mr. Gasket Performance and Racing Products range from $25.99 to $48.09, plus, with more than 22 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.

    Water Neck
    from
    $27.49
    This product is not rated

    Water Neck

    “”

    Thermocap Radiator Cap
    from
    $48.09
    This product is not rated

    Thermocap Radiator Cap

    “”

    High Performance 180 Degree Thermostat for Increased Flow
    from
    $26.99

    (20)

    High Performance 180 Degree Thermostat for Increased Flow

    “Installed in my 95 mustang perfect fit and working better than hopped or expected!!!”

    FAQs for 1969 Buick GS 350 Performance and Racing Products

    Which Performance and Racing Products are best-sellers for 1969 Buick GS 350s?

    Out of 57 Performance and Racing Products that fit 1969 Buick GS 350s, the following parts are the top sellers:

    What’s the price range for 1969 Buick GS 350 Performance and Racing Products?

    Performance and Racing Product prices for the 1969 Buick GS 350 start at $7.69 and go up to $1,138.99 for the most premium parts.

    What’s the average price of a Performance and Racing Product for a 1969 Buick GS 350?

    The average price for Performance and Racing Products for the 1969 Buick GS 350 is $396.98. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.

    Does Advance Auto Parts sell Performance and Racing Products for other Buick GS 350 model years?

    Yes, we currently carry Performance and Racing Products for 1 model years of Buick GS 350s between 1968 and 1968. Performance and Racing Products are bought most frequently for the following model years: 1968.

    What are the cheapest Performance and Racing Products for my 1969 Buick GS 350?

    The cheapest 1969 Buick GS 350 Performance and Racing Products we carry in stock are:

    What types of Performance and Racing Products do you sell for my 1969 Buick GS 350?

    As of 2/5/25, these are some of the most in-demand types of Performance and Racing Products for a 1969 Buick GS 350:

    Can I get help with 1969 Buick GS 350 Performance and Racing Product orders?

    Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Buick Performance and Racing Products and more.

    What is your return policy for Buick GS 350 Performance and Racing Products?

    Advance Auto Parts keeps returns simple. For new Buick GS 350 Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.