1968 Pontiac GTO Differentials

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings
• Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

8.2″ Buick, Oldsmobile, Pontiac cover gasket, 10 bolt holes.

Product Features:

• Cover gasket
• Fits 8.2″ in Buick, Oldsmobile and Pontiac

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits 8.5″ Oldsmobile with 28 spline axles
• Fits 8.5″ Oldsmobile with 31 spline axles
• Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

Product Features:

• RING GEAR BOLT 8.5″ 7.5″ 7/16 X 20 LEFT HAND

Yukon spider gear set for GM 8.2″ Buick, Olds, Pontiac Dura Grip posi, 28 spline. This kit does not include clutches. This kit fits Yukon Dura Grip ONLY.

Product Features:

• Spider gear kit
• Fits 8.2″ Buick, Oldsmobile and Pontiac with Dura Grip positraction
• Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.6″, 12 bolt car and 12 bolt truck differential. This kit contains carrier bearings, races and shims.

Product Features:

• Fits GM 12 bolt passenger car and truck and 8.6″
• Includes carrier bearings and races and “super” carrier shim kit

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

• For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
• The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
• Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
• Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
• Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

• Fits GM 12 bolt passenger car
• 8.875″ ring gear diameter
• 30 spline pinion
• 12 ring gear bolts
• 3.73 ratio
• Thin gear for 4.10 and up carrier

Yukon yoke for GM 8.5″ with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits GM 8.5″
• 30 spline
• 1310 u-joint size
• Outside snap ring design
• 3.219″ snap ring span
• 1.062″ cap diameter
• Strap style

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects. This case is drilled for 3/8″ bolts. Some factory gears use 7/16″ bolts. If your factory gear uses 7/16″ bolts you will need to drill out the ring gear bolt holes.

Product Features:

• Fits GM 8.2″ in Buick, Oldsmobile and Pontiac
• 3.31 ratio and up only
• 4-spring, clutch style positraction
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

• Fits 8.2″ Buick, Oldsmobile and Pontiac
• Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

3/8″ ring gear bolt washer for GM 12 bolt car & truck, 8.2 BOP & more.

Product Features:

• Ring gear bolt washer for GM 12 bolt car and truck, 1955-1964 passenger car, 1963-1979 Corvette and 8.2″ Buick, Oldsmobile and Pontiac

Product Features:

• Super carrier shim kit for Ford 8.8″, GM 12 bolt passenger car and truck, GM 8.0″, 8.6″, 8.6″ IRS and 1963-1979 Corvette
• Interlocking design makes installation much easier

Mini Spool for GM 12P and 12T with 30 spline axles. Mini spools are a low-cost traction option for vehicles looking for full-time lockup. The mini spool installs into a standard open carrier and give 100% power to both tires at all times. These units are not recommended for street-driven vehicles. We recommend full spools for vehicles with large tires or high horsepower. These units come with a one year warranty against manufacturing defects.

Product Features:

• Fits GM 12 bolt passenger car and truck
• Provides 100% traction to both wheels at all times
• Installs into standard open carrier case

21 Piece bearing race driver set. (Box wt: 140lbs) No return.

Product Features:

• Bearing race driver set
• 21 pieces
• All steel construction

Product Features:

• Fits 8.2″ Buick, Oldsmobile and Pontiac
• Chrome

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

Product Features:

• CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN: Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Yukon 1541H alloy rear axle for GM 8.2″ with length of 29-7/8″ and 28 splines axle shaft for use with Buick, Oldsmobile, and Pontiac. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. long splines can be chopped off.

Product Features:

• Fits 8.2″ Buick, Oldsmobile and Pontiac
• 28 spline
• 29 7/8″ long

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

• Includes three quarts of conventional oil

Product Features:

• MINI SPOOL GM 10 BOLT 8 1/2″ 28 SPLINE

Product Features:

• Pinion depth shims for GM 7.5″, 7.625″, 7.6 IFS, 7.6 IRS, 7.75″, 8.2″, 1955-1964 passenger car and 12 bolt car and truck

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

8.5, 9.5, & 8.2 Buick, Oldsmobile, Pontiac GM REDI sleeve yoke saver.Yukon Mighty seal.

Product Features:

• Pinion Redi-sleeve
• Fits GM 8.5″, 9.5″ and 8.2″ Buick, Oldsmobile and Pontiac

Product Features:

• SUPER KIT-GM 12BOLT (CAR)

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!