1968 Pontiac Executive Performance and Racing Products

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes sixteen (16) 3/8 inch-16 x 1-1/4 inch bolts & washers

Product Features:

• Zinc plated Grade 5 steel
• Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
• Ideal For Minimal Space
• 12-Point Head And Flange
• Zinc Plated For Protection

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
• Not intended for use in emission controlled vehicles.

Put an end to high maintenance points ignition systems by installing an ACCEL points eliminator ignition conversion kit. By utilizing specialized electronic circuitry and an infrared signal, ignition timing is stable from 1 to 10,000 RPM. More accurate ignition timing than any other type of system. Improves performance and fuel efficiency. Easy to install with simple hand tools. Reduced maintenance-eliminates changing points forever. Latest thermal clad based surface mount construction for maximum dependability and long life. Available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

• More Accurate Ignition Timing
• Improves Performance And Fuel Economy
• Provides More Accurate Ignition Timing
• Easy To Install w/Hand Tools
• Reduced Maintenance
• Thermal Clad Based Surface Mount Construction
• Utilizes Specialized Electronic Circuitry
• Ignition Timing Is Stable From 1 To 10000rpm

Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

• Easy Installation
• Improved Fuel Economy
• Reduced Maintenance
• Accurate Timing
• Improved Performance
• Provides A Simple Conversion
• No Moving Parts To Wear Out

Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

Product Features:

• Oil Filled For Better Cooling
• Optimized Low Resistance
• Silicon Magnetic Steel E-Core
• Higher Energy/Voltage Outputs
• Quicker Starts
• Improved Idle Quality
• Resists Shock And Vibration
• Resists Corrosion

Heavy duty points sets are quipped with extra think contack arms to prevent flexing at high RPMS. Large radiused tungsten contants provide crisp circuit breaking for peak coil output. High strength phenolic rubbing blocks provide superior durability when used with heavy duty spring tension.

Product Features:

• Extra Thick Contact Arms
• Large Radius Tungsten Contacts
• High Strength Phenolic Rubbing Blocks
• Prevents Points Float
• Moisture-Proof Buna-N Condenser

The throttle cable bracket is designed for small block Chevy engines thru 1979 and is to be used in conjunction with the kick down cable Pn9886 for the Turbo 350 transmission. The throttle cable bracket mounts on the intake manifold and will hold cables with round or square mounts. It has a 2 inch adjustable range and is finished off in a beautiful chrome plating.

Product Features:

• 2 in. adjustable range
• Includes necessary hardware
• Chrome plated
• Individually packaged

If you have custom steel or mag wheels that are not designed without a provision for a center cap, you’re probably looking at an ugly stock dust cap in the center of your front wheels. This chrome dust cap fixes that problem, and is a direct replacement for stock cap 1.790 inches in diameter. Two per set.

Product Features:

• Chrome Plated Steel
• Set of 2 Caps
• Easy Installation
• 2 Per Set

Do yourself and your poncho a favor and replace your points distributor with a Ready-to-Run model. You’ll never have to adjust or replace the points again and your car will run better thanks to the hot MSD sparks. Inside the CNC-machined billet housing the unit incorporates a magnetic pickup that never wears out. Plus, the distributor has a built in ignition module so there is no need to mount an external MSD Ignition control. The module delivers up to 7.5 A to the coil creating a stout inductive spark. Not only do you get the benefits of electronic triggering, but your engine will awaken with powerful sparks from the ignition module. This improves combustion of the fuel mixture resulting in quick starts, a smooth idle and great performance.

Product Features:

• Simple and clean three wire installation
• CARB E.O. Approved
• Does not require an MSD Ignition Control
• Mech. advance assem. can be locked out for crank trigger systems
• Maintenance-free magnetic pickup and precision reluctor
• Creates stable trigger signals throughout the rpm range
• Vacuum advance canister for improved economy (can be locked out)
• Easy-to-adjust mech. advance w/supplied springs and stop bushings
• Built-in module produces a 7.5 amp single spark through high rpm
• Includes built-in Rev Limiter

Hold your alternator securely in place with Mr. Gasket chrome alternator bracket. Chrome plated heavy gauge steel for long lasting good looks. Must be used with #9852.

Product Features:

• Chrome Plated Steel
• F-Style
• Heavy Gauge Steel Construction
• Fits Small Block Chevy 265-400 CID
• Must Be Used With Part 9852

Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermoconductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually.brbrGasket Bore 4.250 inch, Compressed thickness 0.038 inch

Product Features:

• Five layer (graphite core/perforated steel outer layers) composite construction
• Graphite core has excellent thermo-conductivity-transfers heat away from hot spots in head preventing gasket burn-out
• Provides excellent stability, compressibility and high temperature endurance
• Coated with high temperature silicone to ensure sealing of engine fluids
• Will not brinell (indent) aluminum cylinder heads
• For high performance street, drag race and oval track use
• Compatible w/High Octane Fuel
• Compatible With Exotic Fuel

Matched assembly for maximum reliability. An excellent choice for high performance street applications.

Product Features:

• Built As Matched Assembly
• Exceptional Performance
• Exceptional Durability
• Long Term Dependability
• Designed for Street And Street Strip Applications

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:

• High Output Fuel Flow
• Flows 110 gph Free Flow
• Shutoff Pressure Pre-Set From 6.5 To 8 PSI
• Fuel Pressure Regulator Is Not Required
• Heavy Duty Construction For Continuous High rpm Operation
• Fuel Body Casting Can Be Rotated For Plumbing Situations
• Inlet And Outlet Tapped For 1/4 in. NPT
• Inlet/Outlet Tapped For 3/8 in. NPT

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
• With steel core to provide ultimate excellent blowout resistance.
• Not intended for use in emission controlled vehicles.

Designed to keep the rocker arms positively locked for precise and critical valve train adjustments. Manufactured from quality grade steel, then heat-treated for extra strength and plated with a durable finish. Kits include 16 rocker arm nuts with socket head set screws and one hex key wrench.

Product Features:

• (16) Rocker Arm Nuts w/ Locks 3/8″-24 Threads
• Shank O.D. .540″
• Includes Locks and Hex Wrench
• High-Quality Grade Steel
• Heat-Treated For Ex Strength
• Plated With Durable Gold Tone Finish

This Spectre OEM replacement air filter is an easy to install performance option for multiple Buick, Cadillac, Chevy, GM, Mercedes, Oldsmobile and Pontiac applications that use a 14 inch by 3 inch round air filter. With its performance synthetic air filter media, this air filter has been designed to add horsepower and quicker acceleration by allowing more air flow into your engine than ordinary paper filters. This air filter’s sealing edge was engineered to insure a proper air cleaner housing seal for great engine protection.

Product Features:

• Replacement for 14 inch by 3 inch round air filter
• Fits perfectly in your vehicle’s air box as a replacement for your factory air filter
• Engineered for increased flow and greater performance
• Fits select Buick, Cadillac, Chevy, GM, Mercedes, Oldsmobile and Pontiac models
• Factory pre-oiled and ready to use
• Simple installation

The Original Pro Stick shifter delivers rock-solid performance, mixed with clean design cues and compact size. This is why you see so many Pro Stick shifters at the race track. We start off with a heavy duty steel base with a hardened steel gate plate, a reverse lockout feature that only requires one hand to operate, and complies with NHRA/IHRA safety rules. Then add the billet aluminum shift handle with classic white shift knob, lightweight aluminum trigger and finish it off with a brushed aluminum cover with quick release pins, and you end up with one good looking bullet-proof race shifter. Optional Forward and Reverse shift pattern gate plates are available for most popular 2, 3 and 4-speed transmissions. This model Pro Stick comes out of the box ready for action for most popular 3-speed transmissions, includes a 5-foot Super Duty shift cable, brackets, levers, hardware and detailed instructions for an easy installation. Be sure to check out all the optional Magnum Grip side grip plates including the one and two button 12-volt momentary switches or any of the other accessories we offer for the Pro Stick in the Shifter Accessories section. Notes: AOD requires installation kit #40496, AODE & 4R70W requires installation kit #40504, E40D & 4R100 requires installation kit #40505, 2004R & 700R4 require gate plate #80712, 4L60E – 4L85E equipped with PRNDL switch requires cable bracket kit #70499 and gate plate #80712. Overall Dimensions – 8.25L x 2.92W x 9.25H

Product Features:

• All One-Handed
• Reverse Lockout Meets NHRA And IHRA Requirements
• Mount Directly To Floor/Chassis/Or w/Quick Release
• Ultimate For Powerglide Applications
• Lightweight Brushed Alum. Cover
• Cover Removed Quickly and Easily
• Includes 5 Ft. Super Duty Race Cable
• Quick Change Plate Design

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
• Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
• Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
• Slotted bolt holes allow for easier header installation.
• Not intended for use in emission controlled vehicles.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

Product Features:

• Heavy Duty Cap and Rotor Kit
• With Brass Inserts

Edelbrock #88563 Water Pump Pontiac 389-455 standard rotation black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cooli

Product Features:

• Standard Impeller Rotation
• 0.625 in. Pilot Shaft
• 0.750 in. Ball/Ball Bearing
• 4.50 in. Block To Hub Height
• Black Finish

Product Features:

• For Professional Cylinder Head Porter
• 72cc Chamber Size
• As-Cast Casting Has Small Ports And Chambers
• Max Valve Size is 2.11 Int and 1.66 Exh
• 14-Degree Valve Angle
• Enough Wall Thickness For CNC Machining
• Seats and Manganese-Bronze Guides Included

Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.

Product Features:

• 2800-3200 RPM
• Small And Big Blocks
• Serious Performance
• Furnace Brazed
• Fully Balanced

The Edelbrock 1406 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1406 Performer Series 600 CFM electric choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:

• Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
• Electric Choke
• 4 Barrel Count
• Square Bore
• Smooth Secondary Transition
• Both Timed and Full Vacuum Ports
• Includes PCV Outlet

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:

• Good blend of efficiency and performance.
• Perfect choice for performance street rebuilds.
• Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

Available in various sizes, heights, and finishes, Spectre offers a wide variety of high performance valve covers designed to easily replace your stock covers. Designed for 1962-1979 Pontiac V8 engines, this valve cover features chrome plated steel construction and a smooth design. Sold in pairs, this tall profile cover is baffled to provide optimum function. With show quality construction and a sealing edge designed for an ideal fit, our valve covers are engineered to look great for applications ranging from custom builds to replacing stock equipment.

Product Features:

• Designed for 1962-1979 Pontiac V8 engines
• Baffled for breather system compatibility
• Sold in pairs
• Triple chrome-plated steel construction
• Tall profile
• Features OEM style sealing edge

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

Product Features:

• HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
• VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
• PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
• EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
• EASY TO REMOVE: Fast and easy Wrench-Off removal
• HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
• HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods, the Thumpr series’ early i

Product Features:

• Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
• Best with aftermarket converters and more rear gear.
• Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.