from

$284.99

Yukon 1541H alloy cut to fit rear axle for Chrysler 8.75″ measuring 28″-32″ with 30 splines and 5×4.5 bolt pattern. for use with A, C & E-Body. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. Must use Green bearing.

Product Features:

Fits Chrysler 8.75″
30 spline
Cut to length design fits 28″-32″ applcations
5 x 4.5″ bolt pattern

from

$339.99

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

Fits Chrysler 8.75″ ’89’ case housing with 25520 carrier races
Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve , thread locker, marking compound with brush, and gasket.

from

$12.99

8.25″ Chrysler cover gasket.

Product Features:

Cover gasket
Fits Chrysler 8.25″

from

$269.99

Polished aluminum replacement cover for Dana 60 (standard rotation only).

Product Features:

Fits standard rotation Dana Spicer 60
Finned polished aluminum

from

$10.99

Pinion nut for Chrysler 7.25″, 8.0″ IFS, 8.25″, 8.75″ fine spline, 9.25″ front & rear, 7/16″ x 14.

Product Features:

Pinion nut for Chrysler 8.0″ IFS, 8.25″, 8.75″ with 29 spline pinion and 9.25″ rear
7/8″ x 14 thread

from

$5.99

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

Cover bolt for Dana Spicer 60, 70 and 80
3/8″

from

$198.99

Product Features:

Spider gear kit
Fits Dana Spicer 60, 30 spline open differential
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$215.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M802011 race
All steel construction

from

$389.99

Yukon replacement standard open carrier case for Dana 60, 4.56 & up (incl ABS) 2-7/16″ tall.

Product Features:

Standard open carrier case
Does not include spider gears
Fits Dana Spicer 60
4.56 and up ratio only
ABS and non-ABS compatible

from

$104.99

Product Features:

Carrier shims for Dana Spicer 60 and 70U

from

$79.99

Seal housing for Dana 60, Zip locker, with o-rings.

Product Features:

Seal housing for Dana Spicer 60
Includes o-rings

from

$232.99

Product Features:

Clutch kit
Fits Dana Spicer 44 and Chrysler 8.75″ Powr Lok
Aggressive design

from

$108.99

Product Features:

CHRYSLER 7.25″ INTERNAL KIT

from

$51.99

Product Features:

MINI INSTALL KIT CHRYSLER 8.75 8 3/4″ LATE

from

$37.99

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

from

$251.99

Yukon replacement trail repair kit for Dana 60 with 1310 size U/joint and u-bolts. This kit comes with a yoke, U/joint, pinion seal, U/bolt or strap kit, pinion nut, and pinion nut washer (if applicable).

Product Features:

Fits Dana Spicer 60 and 70
1310 u-joint size
Kit includes yoke, U-joint, pinion seal, pinion nut and washer, U-bolts and threadlocker

from

$6.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$223.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Chrysler 7.25″
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$198.99

Product Features:

Spider gear kit
Fits Dana Spicer 60, 35 spline open differential
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$5.99

Product Features:

Floater roll pin
Fits Dana Spicer 44 and Chrysler 8.75″
Powr Lok positraction only

from

$596.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

from

$8.99

Replacement crush sleeve for Dana 60, APROX 0.660″ long.

Product Features:

Crush sleeve for Dana Spicer 60
0.660″ tall

from

$13.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$194.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Dana 60 differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits Dana Spicer 60
Includes carrier bearings and races and carrier shim kit

from

$12.99

Product Features:

KIT SHIM

from

$9.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$519.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features: