from

$41.99

Product Features:

Belleville plate, non-splined
Fits Dana Spicer 44 Powr Lok

from

$301.99

Yukon standard open spider gear replacement kit for Dana 60 and 61 with 35 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fit Dana Spicer 60 open differential with 35 spline axles
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$4.99

Product Features:

Brand may vary by location

from

$219.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$101.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

KIT BRG&SEAL GM 8.5 10BLT NON IFS FRONT / REAR

from

$659.99

Yukon replacement positraction internals for Dana 60 (full- and semi-floating) with 35 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit includes clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Dana Spicer 60 with Trac Loc positraction with 35 spline axles
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$232.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits GM 12 bolt truck
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$414.99

Yukon billet replacement yoke for Dana 60 and 70 with 29 spline pinion and a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 60 and 70
29 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
U-bolt style

from

$79.99

Seal housing for Dana 60, Zip locker, with o-rings.

Product Features:

Seal housing for Dana Spicer 60
Includes o-rings

from

$26.99

Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.

Product Features:

Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
Left hand thread

from

$249.99

Product Features:

Installation kit
Includes o-ring for bulkhead fitting, bulkhead fitting, outer fitting, switch, front and rear switch cover, solenoid, zip ties and 20′ air line

from

$9.99

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
1/2″ head

from

$215.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits HM88510 race
All steel construction

from

$8.99

Positraction clutch guide.

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44, Dana Spicer 50, Ford 8.8″, GM 12 bolt passenger car, GM 8.2″, 8.5″ and 8.6″, 1963-1979 Corvette and Nissan Titan
Compatible with Dura Grip positractions only

from

$57.99

3 Qt. Penzoil 80W90 conventional gear Oil. W/ bottle of Posi additive.

Product Features:

Includes three quarts of conventional oil and one 4oz bottle of Yukon positraction additive

from

$271.99

Differential

from

$9.99

Product Features:

Cross pin bolt for Dana Spicer 60 with c-clip axles

from

$6.49

Product Features:

DANA PRELOAD SHIMS (D60 & D70)

from

$3.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$149.99

Product Features:

Fits Dana Spicer 44 with 30 spline axles
Installs into a standard open carrier case
Provides 100% traction to both wheels at all times
Not recommended for street driven vehicles

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$4.99

Replacement ring gear bolt for Dana 60, 70, 70U & 70HD, 1/2″ x 18.

Product Features:

Ring gear bolt for Dana Spicer 60, 70, 70U and 70HD
1/2″ x 18 thread

from

$69.99

Product Features:

MINI INSTALL KIT GM 12BLT 8.875 TRUCK

from

$4.99

Product Features:

Side gear thrust washer for Dana Spicer 60, 70, 70U, 70HD and 80
Fits standard open differentials only

from

$13.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$809.99

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

Fits Dana Spicer 44 with 30 spline axles
3.92 ratio and up only
4-spring, clutch style positraction
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA

from

$31.49

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$6.99

Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

Product Features: