1967 Lincoln Continental Differentials

Yukon Gear & Axle offers a full line of top quality differential tools to save time and money.

Product Features:

• For Dana 25, 27, 30, 44, 50, and 53 differentials
• Fits 02820 race
• Ensures accurate installation of bearing races

Valvoline Import Multi-Vehicle Automatic Transmission Fluid is specifically formulated for use in most Toyota, Nissan, Honda and other imported vehicles. It is formulated with all synthetic base stocks and a proprietary additive system to ensure optimal transmission performance in a wide variety of vehicles. Valvoline Import Multi-Vehicle ATF can also be used in many domestic vehicles. It meets requirements of General Motors and Ford vehicles. Recommended for use in the following applications: Ford MERCON, GM DEXRON-II and DEXRON-III, BMW LT 71141 and ETL-7045E, Nissan/Infiniti Nissan ATF, Matic-D, Matic-K and Matic-J, Mitsubishi Diamond SP-II and SP-III, Subaru ATF-HP, Hyundai/ KIA SP-II and SP-III, Toyota/Lexus Type T, T-III and T-IV, Honda/Acura ATF-Z1 (except in CVTs), Mercedes Benz NAG1, Volvo passenger car (except AW-1), and Volkswagen/Audi TL52162. For CVT applications Valvoline recommends Valvoline Full Synthetic CVT Fluid.

Product Features:

• Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
• Enhanced anti-shudder protection for smooth shifting and maximum power transfer
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

Yukon Gear & Axle offers a full line of top quality differential tools to save time and money.

Product Features:

• Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or GM and Chrysler 11.5″ 1-ton applications
• Works with an impact gun to safely and easily remove carrier bearings
• Comes with a handy bench-top stand
• For 1-ton applications shop Yukon part YT P22

Yukon Performance 2-3/16″ deck steel spool for 9″ Ford with 40 spline axles. Spool uses 2″ journal bearings (45 degree). Yukon performance spools are made from the highest quality materials to ensure high strength and long life in performance applications. Spools provide 100% power to both tires at all times and are a lower cost alternative to lockers. Spools are not recommended for street driven vehicles. Yukon Performance spools come with a one year warranty against manufacturing defects.

Product Features:

• Fits Ford 9″ with 40 spline axles
• Provides 100% traction to both wheels at all times
• Not recommended for street driven vehicles

Yukon Trac Loc positraction, Ford 8.8″, 31 spline, with Carbon Fiber clutches.

Product Features:

• Trac Loc positraction carrier case
• Includes spider gears
• Fits Ford 8.8″ with 31 spline axles
• Carbon fiber clutches

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• 1.0″ long
• 3/8″-16
• Pinion support bolt for Ford 8″ and 9″ differentials

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

Yukon Gear and Axle manufactures a complete line of general replacement and performance series of pinion yokes for many street, racing, and heavy-duty off-road applications.

Product Features:

• Fits Ford 9″
• 28 spline
• 1330 u-joint size
• Outside snap ring design
• 3.625″ snap ring span
• 1.125″ cap diameter
• U-bolt style

For vehicles that are driven daily, the Power Trax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Power Trax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Power Trax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Power Trax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds.

Product Features:

• The Power Trax Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Power Trax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.
• Power Trax lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.
• Power Trax offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.
• Power Trax ia an Extreme Traction System

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear.

Product Features:

• FORD 9″ EMPTY POSI CASE – 28 & 31 SPLINES

Ford 8″ & 9″ TracLoc ring gear bolt, 1-1/4″ long.

Product Features:

• Ring gear bolt for Ford 8″ and 9″
• For use with Trac Loc limited slip
• 1.25″ long

Yukon Gear & Axle dropouts are heavy duty. They feature upgraded nodular iron construction and a larger-than-OEM design to provide unrivaled strength and reliability in racing and off-road applications.

Product Features:

• Side adjuster
• Fits Ford 9″
• 3.062″ designs only

Dana 70 ABS exciter tone ring.

Product Features:

• Spider gear kit
• Fits Ford 8.8″ 28 spline open differential
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

• Fits Ford 9″
• 9.00″ ring gear diameter
• 28 spline pinion
• 10 ring gear bolts
• 4.11 ratio

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Trac Loc spring plate for Ford 8″ and 9″

Yukon Mighty Seals use the latest design and manufacturing technologies to produce a precision fit that seals tight and lasts for years to come.

Product Features:

• Pinion support O-ring
• Fits Ford 9″

Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.

Product Features:

• Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 in

Product Features:

• Fits Ford 7.5″
• 28 spline
• 4-spring, clutch style positraction
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin shaft
• Fits Ford 9″
• Short design

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits 2009 and down Ford 8.8″
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Pinion gear thrust washer for Ford 8.8″
• 0.875″ diameter cross pin shaft applications only

Yukon Gear & Axle spider gear kits utilize the highest quality materials and best production techniques in the industry to ensure a longer lasting spider gear set. This kit fits Yukon Dura Grip & Eaton positractions and delivers everything needed for a complete and proper spider gear set replacement.

Product Features:

• Fits Ford 8.8″ outfitted with Yukon Dura Grip positraction
• 28 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers
• Does not include clutches

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Side gear thrust washer
• Fits Ford 7.5″

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Pinion nut for Ford 7.5″, 8″ and 9″
• 3/4″ x 20 thread
• 1 1/6″ socket

Product Features:

• MINI INSTALL KIT FORD 7.5