1966 Jeep Wagoneer Performance and Racing Products
Find Your Specific 1966 Jeep Wagoneer Performance and Racing Products
Below you will find various in-demand Jeep Performance and Racing Products, components and accessories for your 1966 Wagoneer. Advance Auto Parts has popular Wagoneer parts like Performance Ignition Products, Performance Fuel Systems, Performance Engines and more. You’ll also find aftermarket and OEM Performance and Racing Products for other Wagoneer model years including
1982,
1983,
1984,
1985,
1986,
1987,
1988,
1989,
1990 and more. Select a category of 1966 Jeep Wagoneer Performance and Racing Products below and start saving instantly.
Popular 1966 Jeep Wagoneer Performance and Racing Products Categories
Essential Performance and Racing Products for 1966 Jeep Wagoneers
Omix – Thermostat 180 Degree; 41-71 Willys/Jeep Models (Part No.17106.02)
from
$8.29
Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA.
Product Features:
See More
Product Features:
- OE Style
- Direct Fit
- Steel
- Better Flow Control
Mr. Gasket – High Performance Thermostat – 160 Degree Brass & Copper (Part No.4363)
from
$29.49
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.
Product Features:
See More
Product Features:
- Opens at 160 Degrees
- Designed to Resist Large Variations of Coolant Pressure at High RPM
- Fully opens at Correct Temperature Consistently Regardless of engine RPM
- For High Performance Street, Drag Race, and Oval Track
- Copper & Brass Construction – Resists Corrosion
- High Flow
Omix – Driveshaft U-Joint; 1310 Spicer (Part No.16585.02)
from
$38.49
Are your U-joints making noise? Or has one broken? When they do break, they usually damage the axle shafts or driveshafts too. That’s a lot of unnecessary work and expense. U-joint replacement is a routine maintenance chore.
Product Features:
See More
Product Features:
- Front/Rear
- OE Style
- Direct Fit
Motive Gear – Drive Shaft Pinion Yoke (Part No.MG1310-6010)
Holley – Street Carburetor: 670 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny (Part No.0-80670)
from
$682.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Holley – Prem Street Carbs (Avengers) (Part No.0-80870)
from
$699.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Mallory – Mallory Kit: Unil Conv: Delco: V8 (Part No.501)
from
$149.99
Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.
Product Features:
See More
Product Features:
- Easy Installation
- Improved Fuel Economy
- Reduced Maintenance
- Accurate Timing
- Improved Performance
- Provides A Simple Conversion
- No Moving Parts To Wear Out
B & M – Holeshot 2400 (Part No.20412)
from
$549.99
HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) Application: HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c
Product Features:
See More
Product Features:
- Furnace Brazed Impeller
- Steel Alloy Pump Drive Tube
- Heavy Duty Needle Bearing
- Between Stator and Turbine
- Furnace Brazed Turbine
B & M – Tork Master 2400 (Part No.20404)
from
$373.99
Torque Converter – Tork Master 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best value priced street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New alloy steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required. Due to torque converter core availability, the actual converter size may vary but performance functionality will be as advertised.
Product Features:
See More
Product Features:
- New Precision Pump Drive Tube
- Pressure Tested
- Fully Balanced
- Needle Thrust Bearing
- New Thrust Washer
B & M – Torque Converter, Nitrous Holeshot 3000 (Part No.20481)
from
$899.99
Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.
Product Features:
See More
Product Features:
- 2800-3200 RPM
- Small And Big Blocks
- Serious Performance
- Furnace Brazed
- Fully Balanced
Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)
from
$199.99
Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).
Product Features:
See More
Product Features:
- Glass Filled Polyester Case
- Longer Spark Duration
- Increased Performance
- No Energy Loss Due To Arcing
- Includes Brass Contact Terminal
Mallory – Distributor Wiring Harness (Part No.29349)
Mallory – Unilite Ignition Module (Part No.605)
from
$92.99
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.
Product Features:
See More
Product Features:
- Service Part
- No Moving Parts To Wear Out
- Self Contained Unit
- Can Drive OEM
- Can Drive High Performance Ignition Coils
Mallory – Unilite Electronic Ignition Distributor Series 37 (Part No.3760001)
from
$599.99
The industry standard with adjustable mechanical advance curve. Triggered by photo-optic infrared LED system. Improved combustion efficiency and economy, increased spark plug life and cold weather starting, and maintenance free operation.
Product Features:
See More
Product Features:
- Improved Combustion And Economy
- Increased Spark Plug Life
- Improved Cold Weather Starting
- Maintenance Free Operation
- Accurate Spark Timing
- Self-Lubricating Bushings
- Years Of Trouble-Free Service
MSD Ignition – Distributor; AMC V8 Engines (Part No.8519)
from
$525.99
There is a big following of AMC enthusiasts that are cruising a 401 equipped Javelin or trail blazing in a rock crawling Jeep with an inline 6-cylinder! MSD offers two Pro-Billet distributors to deliver accurate trigger signals and are maintenance-free! Under the brass terminal cap of each distributor is MSD’s race proven magnetic pick-up. This pick-up never requires adjustment and simply plugs right into an MSD Ignition control. Just above it and under our strong race rotor is an adjustable mechanical advance assembly. The chro-moly weights of this assembly slide on nylon bushings producing smooth movement of the timing. You can easily adjust the curve to match your engine’s requirements with the supplied springs and stop bushings. Each precision CNC-machined billet aluminum housing features a sealed ball-bearing and long sintered bushing for stability at any RPM and increased endurance. An oversized steel shaft receives a QPQ coating to reduce friction and prevent corrosion.
Product Features:
See More
Product Features:
- Designed For Street/Performance Use w/Mech or Vacuum Advance
- Must Be Used w/An MSD Ignition Control
- Supplied w/HEI style distributor cap/rotor (accepts Cap-A-Dapts)
- QPQ coated polished steel shaft; guided by sealed ball bearings
- Maintenance-free magnetic pickup and precision reluctor
- Creates stable trigger signals throughout the rpm range
- Easy-to-adjust mech. advance w/supplied springs and stop bushings
- Vacuum advance canister for improved economy (can be locked out)
Accel – Supercoil (Part No.140001)
from
$114.99
Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.
Product Features:
See More
Product Features:
- Oil Filled For Better Cooling
- Optimized Low Resistance
- Silicon Magnetic Steel E-Core
- Higher Energy/Voltage Outputs
- Quicker Starts
- Improved Idle Quality
- Resists Shock And Vibration
- Resists Corrosion
Accel – Super Stock Replacement Coil for Improved Performance, Starting, and Power (Part No.8140)
from
$45.99
Excellent high performance replacement for import and domestic vehicles with canister type oil filled coil. Re-engineered windings for even higher energy output resulting in quicker starting improved throttle response and more high RPM power. Designed to work with Points style and Breakerless electronic ignition systems. Heavy duty black Alkyd tower provides in flashover in protection to primary terminals. ACCEL Yellow can. 42000 volts effective up to 6500 RPM 1.4 ohms on the primary
Product Features:
See More
Product Features:
- 42000 Volts
- Effective To 6500 RPM
- Quicker Starting
- Improved Throttle Response
- Higher RPM Power
- Can Finished In Yellow
Omix – Ignition Coil; 72-74 Jeep CJ Models (Part No.17247.06)
from
$48.99
Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA.
Product Features:
See More
Product Features:
- Copper Wire
- OE Style
- Direct Fit
Omix – Tie Rod End Tube (Part No.18046.03)
from
$26.49
Is your Jeep’s steering loose? Are your tires wearing in an uneven pattern? Chances are that some of your steering components are worn. Fixing them is cheaper than replacing your tires and it’s a whole lot safer too.
Product Features:
See More
Product Features:
- Steel
- OE Style
- Direct Fit
Mr. Gasket – Thermocap Radiator Cap (Part No.2470B)
from
$54.99
The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.
Product Features:
See More
Product Features:
- Indicates coolant temperature
- Helps prevent coolant injuries
- Fahrenheit and centigrade readings
- Color-coded temperature ranges
- Integrated coolant reclamation valve
- Improves under-hood appearance
- Chromed crown with a colored trim ring
Energy Suspension – Motor Mount (Part No.2.1104R)
from
$69.99
A true performance application component for cars, trucks, hot rods and racing/competition vehicles – yet designed to be also used for street vehicles. Soft-running enough to absorb vibrations for street use yet rugged for racing use. When required- a torque resistant safety interlock design is used that is comparable in strength to those too hard-running metal mounts. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal motor mounts. The popular early style mounts for General Motors vehicles are available in either zinc or chrome metal finishes. Made of Hyper-Flex performance polyurethane. Resistant to under vehicle fluids such as: oils, coolants, road contaminants, etc.
Product Features:
See More
Product Features:
- Gains Both Performance and Longevity
- Will Handle Any and All Torque
- Out Lasts Rubber
Energy Suspension – Motor Mount (Part No.2.1104G)
from
$69.99
A true performance application component for cars, trucks, hot rods and racing/competition vehicles – yet designed to be also used for street vehicles. Soft-running enough to absorb vibrations for street use yet rugged for racing use. When required- a torque resistant safety interlock design is used that is comparable in strength to those too hard-running metal mounts. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal motor mounts. The popular early style mounts for General Motors vehicles are available in either zinc or chrome metal finishes. Made of Hyper-Flex performance polyurethane. Resistant to under vehicle fluids such as: oils, coolants, road contaminants, etc.
Product Features:
See More
Product Features:
- Gains Both Performance and Longevity
- Will Handle Any and All Torque
- Out Lasts Rubber
Omix – Engine Mount (Part No.17473.07)
from
$58.99
Is your Jeep engine moving too much when you rev it up? Are there unusual noises when you accelerate? The rubber in the engine mounts takes a beating from engine torque every time you use the gas pedal.
Product Features:
See More
Product Features:
- Left Or Right Side
- OE Style
- Direct Fit
Rugged Ridge – Engine Mount Kit; Aluminum (Part No.18390.20)
from
$174.99
Rugged Ridge Solid Motor mounts are built from 6061-T6 Aluminum with a tensile strength of 42,000 psi. Built to replace your wimpy OE rubber engine mounts to eliminate weight transfer on the trail torque loss and binding that result in excess engine movement.
Product Features:
See More
Product Features:
- Aluminum
- Pair
Lakewood – Trans Mount: Urethane-Chevy (Part No.24350)
from
$97.99
Constructed of durable polyurethane to handle the stress oh high horsepower. Absorbs vibration and lasts longer than rubber Features unique built-in safety lock to keep from separating under high torque loads. Ideal for use on street or strip applications. Complete with grade-8 mounting hardware.
Product Features:
See More
Product Features:
- Durable Polyurethane
- Absorbs Vibration
- Last Longer Than Rubber
- Built-In Safety Lock
Upgrade your 1966 Jeep Wagoneer with Top-Quality Performance and Racing Products
When it comes to maintaining or upgrading your 1966 Jeep Wagoneer, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Jeep or enhancing its overall performance, Performance and Racing Products are key to keeping your Wagoneer functioning at its best. At Advance Auto Parts, we offer a wide selection of 27 Performance and Racing Products for the 1966 Jeep Wagoneer, designed to meet your needs without breaking the bank.
From
Performance Ignition Product
replacements to
Performance Fuel Systems
upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.
Affordable Prices and Wide Selection
Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1966 Jeep Wagoneer at great prices.
Our Performance and Racing Products inventory for this model
ranges from just $8.29 to $949.99, with
an average price of $334.60.
Our 27 Performance and Racing Products in stock come from 8 trusted brands, so you’re sure to find the right part for your 1966 Jeep Wagoneer without overspending.
Top Brands and High Customer Satisfaction
Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1966 Jeep Wagoneer, we stock popular OEM and aftermarket Performance and Racing Products from top names
like Mallory, Omix, Holley, and more.
Mallory Performance and Racing Products
start at just $92.99 and boast an impressive 4.9 stars average rating from customers.
Omix and Holley also bring quality to the table, with Performance and Racing Products available starting at $8.29, and at an average 4.3 stars rating.
With 186 customer reviews and counting, our 1966 Jeep Wagoneer Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.
Explore Related Parts and More
While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants
and more to make sure your 1966 Jeep Wagoneer is always ready to roll. We’re committed to providing you with everything you need to keep your Wagoneer in top shape, all in one place.
Start shopping confidently below for your 1966 Jeep Wagoneer!
Best-Selling Performance Ignition Products for 1966 Jeep Wagoneers
Enhance the driving experience in your Jeep with 6 quality Performance Ignition Product components, starting at $33.99.
Mallory – Unilite Ignition Module (Part No.605)
from
$92.99
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.
Product Features:
See More
Product Features:
- Service Part
- No Moving Parts To Wear Out
- Self Contained Unit
- Can Drive OEM
- Can Drive High Performance Ignition Coils
Mallory – Mallory Kit: Unil Conv: Delco: V8 (Part No.501)
from
$149.99
Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.
Product Features:
See More
Product Features:
- Easy Installation
- Improved Fuel Economy
- Reduced Maintenance
- Accurate Timing
- Improved Performance
- Provides A Simple Conversion
- No Moving Parts To Wear Out
Accel – Super Stock Replacement Coil for Improved Performance, Starting, and Power (Part No.8140)
from
$45.99
Excellent high performance replacement for import and domestic vehicles with canister type oil filled coil. Re-engineered windings for even higher energy output resulting in quicker starting improved throttle response and more high RPM power. Designed to work with Points style and Breakerless electronic ignition systems. Heavy duty black Alkyd tower provides in flashover in protection to primary terminals. ACCEL Yellow can. 42000 volts effective up to 6500 RPM 1.4 ohms on the primary
Product Features:
See More
Product Features:
- 42000 Volts
- Effective To 6500 RPM
- Quicker Starting
- Improved Throttle Response
- Higher RPM Power
- Can Finished In Yellow
Accel – Supercoil (Part No.140001)
from
$114.99
Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.
Product Features:
See More
Product Features:
- Oil Filled For Better Cooling
- Optimized Low Resistance
- Silicon Magnetic Steel E-Core
- Higher Energy/Voltage Outputs
- Quicker Starts
- Improved Idle Quality
- Resists Shock And Vibration
- Resists Corrosion
Mallory – Distributor Wiring Harness (Part No.29349)
Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)
from
$199.99
Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).
Product Features:
See More
Product Features:
- Glass Filled Polyester Case
- Longer Spark Duration
- Increased Performance
- No Energy Loss Due To Arcing
- Includes Brass Contact Terminal
Most Popular 1966 Jeep Wagoneer Performance Fuel Systems
Customize your Jeep with 4 Performance Fuel Systems products
like Performance Carburetors, all
priced under $699.99.
Holley – Street Carburetor: 600 CFM, Electric Choke, 4 Barrel, Square Bore, Single Inlet, Shiny (Part No.0-80457S)
from
$499.99
Holley’s new 0-80457SA is constructed from aluminum which compared to its zinc counterpart equates to a weight savings of 40%! Holley’s aluminum 0-80457SA will hold its shine longer and also can be hand polished for a custom look! Its 600 CFM of airflow,
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
Holley – Street Carburetor: 670 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny (Part No.0-80670)
from
$682.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Holley – Prem Street Carbs (Avengers) (Part No.0-80870)
from
$699.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Holley – Prem Street Carbs (Avengers) (Part No.0-80570)
from
$699.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet-Flow Tested To Assure It Arrives Ready To Run
- Street Ready; Out Of The Box
Top Picks for 1966 Jeep Wagoneer Performance Engines
Upgrade Jeep Wagoneers with top-quality Performance Engines parts, including 11 OEM and aftermarket selections for your 1966 model.
B & M – Tork Master 2400 (Part No.20404)
from
$373.99
Torque Converter – Tork Master 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best value priced street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New alloy steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required. Due to torque converter core availability, the actual converter size may vary but performance functionality will be as advertised.
Product Features:
See More
Product Features:
- New Precision Pump Drive Tube
- Pressure Tested
- Fully Balanced
- Needle Thrust Bearing
- New Thrust Washer
Omix – Thermostat 180 Degree; 41-71 Willys/Jeep Models (Part No.17106.02)
from
$8.29
Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA.
Product Features:
See More
Product Features:
- OE Style
- Direct Fit
- Steel
- Better Flow Control
Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)
from
$29.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.
Product Features:
See More
Product Features:
- Opens At 180 Degrees
- Designed to Resist Large Variations of Coolant Pressure at High RPM
- Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
- For High Performance Street, Drag Race, and Oval Track
- Copper & Brass Construction – Resists Corrosion
- High Flow
Mr. Gasket – High Performance Thermostat – 160 Degree Brass & Copper (Part No.4363)
from
$29.49
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.
Product Features:
See More
Product Features:
- Opens at 160 Degrees
- Designed to Resist Large Variations of Coolant Pressure at High RPM
- Fully opens at Correct Temperature Consistently Regardless of engine RPM
- For High Performance Street, Drag Race, and Oval Track
- Copper & Brass Construction – Resists Corrosion
- High Flow
Mr. Gasket – High Performance Thermostat (Part No.4365)
from
$31.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.
Product Features:
See More
Product Features:
- Opens At 195 Degrees
- Designed to Resist Large Variations of Coolant Pressure at High RPM
- Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
- For High Performance Street, Drag Race, and Oval Track
- Copper & Brass Construction – Resists Corrosion
- High Flow
B & M – Performance Torque Converter for GM TH400, 350, & 375 Transmissions (Part No.20400)
from
$329.99
Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost
Product Features:
See More
Product Features:
- New Precision Pump Drive Tube
- Pressure Tested
- Fully Balanced
- Needle Thrust Bearing
- New Thrust Washer
B & M – Holeshot 3600 (Part No.20425)
from
$949.99
HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.
Product Features:
See More
Product Features:
- Furnace Brazed Impeller
- Steel Alloy Pump Drive Tube
- Heavy Duty Needle Bearing
- Between Stator and Turbine
- Furnace Brazed Turbine
- Dual Pattern Drive Lugs
- New Turbine Hub
- New Springs/Rollers In Stator
B & M – Holeshot 3000 (Part No.20413)
from
$899.99
HoleShot 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c
Product Features:
See More
Product Features:
- Furnace Brazed Impeller
- Steel Alloy Pump Drive Tube
- Heavy Duty Needle Bearing
- Between Stator and Turbine
- Furnace Brazed Turbine
B & M – Torque Converter, Nitrous Holeshot 3000 (Part No.20481)
from
$899.99
Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.
Product Features:
See More
Product Features:
- 2800-3200 RPM
- Small And Big Blocks
- Serious Performance
- Furnace Brazed
- Fully Balanced
B & M – Torque Converter, Nitrous Holeshot 3600 (Part No.20482)
from
$749.99
Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.
Product Features:
See More
Product Features:
- 3400-3800 RPM
- Small And Big Blocks
- Serious Performance
- Furnace Brazed
- Fully Balanced
B & M – Holeshot 2400 (Part No.20412)
from
$549.99
HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) Application: HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c
Product Features:
See More
Product Features:
- Furnace Brazed Impeller
- Steel Alloy Pump Drive Tube
- Heavy Duty Needle Bearing
- Between Stator and Turbine
- Furnace Brazed Turbine
In-Demand Performance Steering Products for 1966 Jeep Wagoneers
Select from 1 premium Performance Steering Products parts for your 1966 Jeep Wagoneer.
Omix – Tie Rod End Tube (Part No.18046.03)
from
$26.49
Is your Jeep’s steering loose? Are your tires wearing in an uneven pattern? Chances are that some of your steering components are worn. Fixing them is cheaper than replacing your tires and it’s a whole lot safer too.
Product Features:
See More
Product Features:
- Steel
- OE Style
- Direct Fit
Most Sold 1966 Jeep Wagoneer Performance Distributors
Explore our best-selling Jeep parts for the 1966 Wagoneer among 1 OEM and aftermarket options starting from $599.99.
Mallory – Unilite Electronic Ignition Distributor Series 37 (Part No.3760001)
from
$599.99
The industry standard with adjustable mechanical advance curve. Triggered by photo-optic infrared LED system. Improved combustion efficiency and economy, increased spark plug life and cold weather starting, and maintenance free operation.
Product Features:
See More
Product Features:
- Improved Combustion And Economy
- Increased Spark Plug Life
- Improved Cold Weather Starting
- Maintenance Free Operation
- Accurate Spark Timing
- Self-Lubricating Bushings
- Years Of Trouble-Free Service
Top-Rated Performance and Racing Products Brands For Your 1966 Jeep Wagoneer
Shop for the best-rated brands offering Performance and Racing Products and other products for your 1966 Jeep Wagoneers. Below you’ll find some of our best rated Performance and Racing Products from Mallory, Omix, and Holley, and more. Performance and Racing Products from these brands that fit a 1966 Wagoneer start at just $8.29 and are rated as high as 4.9 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.
Popular Mallory 1966 Jeep Wagoneer Performance and Racing Products
When it comes to maintaining or upgrading your 1966 Jeep Wagoneer, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. Mallory ticks all of those boxes. We offer a wide selection of Mallory Performance and Racing Products, specifically designed for the 1966 Jeep Wagoneer. With over 2 Mallory brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $92.99, with an average price of just $121.49. Plus, with over 4 customer reviews and an average rating of 4.9 stars, you can trust that our Mallory Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.
from
$92.99
(3)
Unilite Ignition Module
“I like the Unilite product because it is so small and compact compared to the HEI stuff I normally use. If you are restricted on space Its a great pro”
from
$149.99
(1)
Mallory Kit: Unil Conv: Delco: V8
“I had my 66 LeMans 326 engine rebuilt. After the install, which was easy to do, and following the instructions the engine fired right up. Now I won’t ”
Popular Omix 1966 Jeep Wagoneer Performance and Racing Products
Omix auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1966 Jeep Wagoneer owner should feel confident when installing genuine Omix parts in their vehicle. To ensure the best fit and performance for your 1966 Wagoneer, Advance Auto Parts carries a full inventory of 1 Omix Performance and Racing Products. Plus you will be keeping your Jeep in peak condition while saving money because prices on these Omix Performance and Racing Products range up to $8.29, plus, with more than 2 customer reviews and an impressive 4.3 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.
from
$8.29
(2)
Thermostat 180 Degree; 41-71 Willys/Jeep Models
“Product is great. Installing next weekend to my jeep”
FAQs for 1966 Jeep Wagoneer Performance and Racing Products
Which Performance and Racing Products are best-sellers for 1966 Jeep Wagoneers?
Out of 27 Performance and Racing Products that fit 1966 Jeep Wagoneers, the following parts are the top sellers:
- High Performance 180 Degree Thermostat for Increased Flow (17360033) – $29.99
- High Performance Thermostat – 160 Degree Brass & Copper (17360031) – $29.49
- Street Carburetor: 600 CFM, Electric Choke, 4 Barrel, Square Bore, Single Inlet, Shiny (6340008) – $499.99
What’s the price range for 1966 Jeep Wagoneer Performance and Racing Products?
Performance and Racing Product prices for the 1966 Jeep Wagoneer start at $8.29 and go up to $949.99 for the most premium parts.
What’s the average price of a Performance and Racing Product for a 1966 Jeep Wagoneer?
The average price for Performance and Racing Products for the 1966 Jeep Wagoneer is $334.60. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.
Does Advance Auto Parts sell Performance and Racing Products for other Jeep Wagoneer model years?
What are the cheapest Performance and Racing Products for my 1966 Jeep Wagoneer?
The cheapest 1966 Jeep Wagoneer Performance and Racing Products we carry in stock are:
- Thermostat 180 Degree; 41-71 Willys/Jeep Models (10186688) – $8.29
- Tie Rod End Tube (10945548) – $26.49
- High Performance Thermostat – 160 Degree Brass & Copper (17360031) – $29.49
- High Performance 180 Degree Thermostat for Increased Flow (17360033) – $29.99
- High Performance Thermostat (22903641) – $31.99
What are the top-rated Performance and Racing Products that fit the 1966 Jeep Wagoneer?
Out of 186 reviews by customers, our 1966 Jeep Wagoneer Performance and Racing Products have an average customer rating of . These are some of the highest-rated Performance and Racing Product types for the 1966 Jeep Wagoneer and their top-rated products:
- Performance Engines
- Tork Master 2400 (17130009) – $373.99
- Thermostat 180 Degree; 41-71 Willys/Jeep Models (10186688) – $8.29
- High Performance 180 Degree Thermostat for Increased Flow (17360033) – $29.99
- Performance Ignition Products
- Tork Master 2400 (17130009) – $373.99
- Thermostat 180 Degree; 41-71 Willys/Jeep Models (10186688) – $8.29
- High Performance 180 Degree Thermostat for Increased Flow (17360033) – $29.99
What types of Performance and Racing Products do you sell for my 1966 Jeep Wagoneer?
As of 11/2/25, these are some of the most in-demand types of Performance and Racing Products for a 1966 Jeep Wagoneer:
Can I get help with 1966 Jeep Wagoneer Performance and Racing Product orders?
Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Jeep Performance and Racing Products and more.
What is your return policy for Jeep Wagoneer Performance and Racing Products?
Advance Auto Parts keeps returns simple. For new Jeep Wagoneer Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.
