1966 Jeep CJ3 Belts and Hoses
More 1966 Jeep CJ3 Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 1966 Jeep CJ3, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 1966 Jeep CJ3 Belts and Hoses
Gates – Premium Molded Coolant Hose (Part No.20701)
from
$27.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Vulco-Flex« II Flexible Coolant Hose (Part No.25477)
from
$17.79
Gates Vulco-Flex(R) II hose will bend in almost any direction. It easily replicates the angles and planes of a wide variety of expensive original equipment coolant hose, for quick, easy replacement.
Product Features:
See More
Product Features:
- Improved sealing surface for greater leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimum inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature Range: up to +257 Deg. F (+125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Bottom Cog V-Belt; 43.5 Inch Long, Exact Fit Premium Quality (Part No.15435)
from
$16.79
Dayco has combined raw-edge construction and a smooth top to ensure high performance on vehicles and drives that utilize V-belts. The Dayco high performance V-belt delivers more flexibility and increases airflow around the belt so it runs cooler and lasts longer. Three plies of neoprene impregnated fabric resist heat, oil and grease while a specially-formulated treatment of the polyester cord provides the strength, stability and reliability that are required for one of the most innovative, top-performing V-belts.
Product Features:
See More
Product Features:
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Prevents electromechanical interference issues on modern vehicles
- Resists heat, oil and grease
Omix – Fan Belt (Part No.17110.01)
from
$17.79
Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA. Limited five year Manufacturer’s warranty.
Product Features:
See More
Product Features:
- OE Style
- Direct Fit
- Rubber
- Long Lasting
- Limited 5 Year Warranty
Omix – Radiator Hose Clamp (Part No.17115.01)
from
$6.79
Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA. Limited five year Manufacturer’s warranty.
Product Features:
See More
Product Features:
- OE Style
- Direct Fit
- Stainless Steel
- Sold Individually
- Limited 5 Year Warranty
Omix – Hose Clamp (Part No.17115.03)
from
$3.49
Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA. Limited five year Manufacturer’s warranty.
Product Features:
See More
Product Features:
- OE Style
- Direct Fit
- Stainless Steel
- Sold Individually
- Limited 5 Year Warranty
Crown Auto Jeep Replacmnt – Front Or Rear Brake Tee: (Mounts On Axle) (Part No.J0637432)
Dayco – Flex Radiator Hoses; EPDM Rubber, 15.75 Inch Long, 1.5 Inch Inner Dia. (Part No.81161)
from
$19.49
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Gates – Premium Molded Coolant Hose (Part No.21660)
from
$23.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Vulco-Flex« II Flexible Coolant Hose (Part No.25478)
from
$18.49
Gates Vulco-Flex(R) II hose will bend in almost any direction. It easily replicates the angles and planes of a wide variety of expensive original equipment coolant hose, for quick, easy replacement.
Product Features:
See More
Product Features:
- Improved sealing surface for greater leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimum inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature Range: up to +257 Deg. F (+125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)
from
$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)
from
$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
Dayco – Flex Radiator Hoses; EPDM Rubber, 12.25 Inch Long, 1.5 Inch Inner Dia. (Part No.81141)
from
$16.79
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Gates – Straight Heater Hose: EPDM, Direct Fit, 0.625" Inside Diameter (Sold by foot) (Part No.28411)
from
$1.49
Premium hose constructed for long service life.
Product Features:
See More
Product Features:
- Good resistance to high temperatures for extended periods of time, which prolongs service life
- Meets SAE 20R3 Standard Wall Class D-2 requirements
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- CAUTION: Do not use for fuel or oil transfer applications
- CAUTION: Do not use for fuel or oil transfer applications
- PLEASE NOTE: Item is priced and sold by the foot. See store for details.
Gates – Premium Molded Coolant Hose (Part No.20168)
from
$31.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Flex Radiator Hoses; EPDM Rubber, 17.25 Inch Long, 1.5 Inch Inner Dia. (Part No.81171)
from
$20.49
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Gates – Straight Heater Hose: EPDM, Direct Fit, 0.75" Inside Diameter (Sold by foot) (Part No.28412)
from
$3.99
Premium hose constructed for long service life.
Product Features:
See More
Product Features:
- Good resistance to high temperatures for extended periods of time, which prolongs service life
- Meets SAE 20R3 Standard Wall Class D-2 requirements
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- CAUTION: Do not use for fuel or oil transfer applications
- CAUTION: Do not use for fuel or oil transfer applications
- PLEASE NOTE: Item is priced and sold by the foot. See store for details.
Omix – Water Pump Bypass Hose (Part No.17116.02)
from
$11.99
Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA. Limited five year Manufacturer’s warranty.
Product Features:
See More
Product Features:
- OE Style
- Direct Fit
- Limited 5 Year Warranty
Yukon Gear – Seal Puller Tool (Part No.56063)
Omix – Defrost Duct (Part No.17907.01)
from
$33.99
Is the plastic defroster duct on the top of your Jeep dash broken or missing? The sun and age can make them crumble. Omix-ADA offers the replacement part you need for your CJ.
Product Features:
See More
Product Features:
- OE Style
- Direct Fit
- Removes Moisture
- Clear View Of Road At All Times
- Limited 5 Year Warranty
Popular 1966 Jeep CJ3 Belts and Hoses Categories
1966 Jeep CJ3 Belts and Hoses
You count on your 1966 Jeep CJ3 to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 29 Belts and Hoses ranging in price from $1.49 to $79.99, you’re sure to find everything you need for your 1966 Jeep CJ3.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 7 different brands like Dayco, Omix, and Imperial. 1966 Jeep CJ3 Belts and Hoses start as low as $1.49!
One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 42 extensive product reviews on 1966 Jeep CJ3 Belts and Hoses. Some of the top-rated Belts and Hoses products we carry are Curved Radiator Hoses: EPDM Rubber, Standard Duty, 12.50" Long, 1.50" Diameter with 1.0 stars.
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 1966 Jeep CJ3 below to get started!
Top-Rated Belts and Hoses Brands For Your 1966 Jeep CJ3
Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1966 Jeep CJ3 running right for years to come. In our inventory you’ll find brands like Dayco, Omix, Imperial, and even more.
Popular Driveworks Belts and Hoses
You’ll find popular Driveworks brand products across Serpentine and V Belts. All are waiting to get your 1966 Jeep CJ3 back on the road. Some of the top-rated Driveworks products in these categories are:
Top-Rated Dayco Belts and Hoses
If Dayco are what you’re looking for, our inventory holds plenty. We stock Dayco brand Belts and Hoses for your 1966 Jeep CJ3, and some of our most reviewed Dayco parts include:
from
$24.99
(16)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 12" Long, 1.50" Diameter
Coolant Hoses
from
$19.49
(3)
Flex Radiator Hoses; EPDM Rubber, 13.88 Inch Long, 1.5 Inch Inner Dia.
Lower Radiator Hoses
from
$16.79
(2)
Flex Radiator Hoses; EPDM Rubber, 12.25 Inch Long, 1.5 Inch Inner Dia.
Upper Radiator Hoses
FAQs for 1966 Jeep CJ3 Belts and Hoses
What are the most purchased Belts and Hoses for the 1966 Jeep CJ3?
Out of 29 Belts and Hoses for the 1966 Jeep CJ3, the most popular in our inventory are:
from
$19.49
(1)
Flex Radiator Hoses; EPDM Rubber, 15.75 Inch Long, 1.5 Inch Inner Dia.
Lower Radiator Hoses
What are the top-rated 1966 Jeep CJ3 Belts and Hoses?
Top-rated Belts and Hoses for your 1966 Jeep CJ3 based on customer reviews/ratings are:
from
$23.99
(2)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 12.50" Long, 1.50" Diameter
“Wrong part for as described”
