from

$154.99

Yukon yoke for GM 7.5″ and 7.625″ (mech 3R) in a triple lip design. 2.556″ snap ring span, 1.125″ cap diameter. Inside snap ring. This yoke uses inside clips. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits GM 7.5″ and 7.625″
27 spline
Mechanics 3R u-joint size
2.556″ snap ring span
1.125″ cap diameter
Inside snap ring design
Strap style

from

$137.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

GM 10 BOLT 8.5 BRG MSTR KIT W/EATON OR AUBURN PRO TIMKEN

from

$109.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.2″ & 8.5″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits GM 7.5″, 7.625″ 8.2″ and 8.5″
Includes carrier bearings and races and “super” carrier shim kit

from

$279.99

Yukon positraction internals for 7.5″ and 7.625″ GM with 28 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects. This kit fits Yukon Dura Grip & Eaton positraction cases. It is not compatible with any other positractions.

Product Features:

Spider gear kit
Fits GM gm 7.5″ and 7.625″ with 28 spline Dura Grip positraction
Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$386.99

Replacement bare case for GM 8.5″ & 8.6″ Yukon Dura Grip. Fits both 28 & 30 spline applications. This carrier case is for a Yukon Dura Grip ONLY. It is NOT a replacement carrier for a stock positraction.

Product Features:

Dura Grip positraction carrier case
Does not include spider gears
Fits GM 8.5″ and 8.6″
Fits 2.76 and up ratios only

from

$14.49

Valvoline DEXRON-VI/MERCON LV ATF is a full-synthetic transmission fluid formulated with advanced additive technology to meet and exceed the requirements of the General Motors DEXRON-VI specification. It is officially licensed and approved by GM and is fully back-serviceable and can be used wherever DEXRON-II and/or DEXRON-III are recommended. Recommended for use in the following applications: DEXRON-VI, DEXRON-III, DEXRON-II, and Allison C-4.

Product Features:

Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
Enhanced anti-shudder protection for smooth shifting and maximum power transfer
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$8.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$38.99

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$6.49

This differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles.
Required replacement – when servicing the differential
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$7.79

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$4.99

3/8″ ring gear bolt washer for GM 12 bolt car & truck, 8.2 BOP & more.

Product Features:

Ring gear bolt washer for GM 12 bolt car and truck, 1955-1964 passenger car, 1963-1979 Corvette and 8.2″ Buick, Oldsmobile and Pontiac

from

$9.49

Product Features:

KIT SHIM PINION

from

$282.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 8.2″ Buick, Oldsmobile and Pontiac
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$59.99

Product Features:

Super carrier shim kit for Ford 8.8″, GM 12 bolt passenger car and truck, GM 8.0″, 8.6″, 8.6″ IRS and 1963-1979 Corvette
Interlocking design makes installation much easier

from

$284.99

Yukon 1541H alloy rear axle for GM 7.5″ passenger with a length of 30-1/2 inches and 26 splines. 2.775″ hub. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a C-clip axle.

Product Features:

Fits 1977-1991 GM passenger car
26 splines
30 1/2″ long
2.775″ brake pilot

from

$9.99

Pinion nut for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.0″, 8.25″, 8.5″, 8.6″, 9.25″ IFS, 9.5″ & Oldsmobile Dropouts. 1 1/4″ socket, 7/8″ x 14 thread.

Product Features:

Pinion nut for GM 7.2″, 7.5″, 7.625″, 8.0″, 8.25″ IFS, 8.5″, 8.6″, 9.25″ IFS and 9.5″
7/8″ x 14 thread
1 1/4″ socket

from

$480.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

from

$0.91

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$379.99

Product Features:

Fits GM 7.5″ and 7.625″
Aluminum girdle cover

from

$59.99

Product Features:

8.5 “P” AXLE MINI INSTALL KIT

from

$188.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M86610 race
All steel construction

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$48.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush. (includes Supershims)

Product Features:

Fits GM 8.5″ rear
Included are a pinion seal, crush sleeve , complete shim kit, marking compound and brush.

from

$216.99

Product Features:

GM 10BL 7.5&7.625 R/P 4.10 MG 10 3/8 X 18 LH THRED BLTS, PD=1.438

from

$551.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$14.29

Product Features:

Brand may vary by location

from

$18.09

Mr. Gasket Axle Housing/Differential Cover or Rear End Gaskets are manufactured from a .047 inch thick cellulose/nitrile composite gasket material for excellent sealing and durability. They are precision die-cut for an excellent fit. Fits 1964-1970 Chevrolet 8.2 inch 10 bolt & 1970-1981 GM 8.5 inch ring gear

Product Features:

.047″ thick cellulose/nitrile composite gasket material
Precision die cut
Reusable

from

$7.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes