1964 Dodge Dart Performance and Racing Products
More 1964 Dodge Dart Performance and Racing Products Categories
If you’re looking for an original Performance and Racing Products replacement for a 1964 Dodge Dart, you can search through our selection below. You’ll also find aftermarket and OEM Performance and Racing Products to meet your needs.
Essential 1964 Dodge Dart Performance and Racing Products
Mr. Gasket – Intake Manifold Bolts (Part No.6091)
from
$32.09
These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.
Product Features:
See More
Product Features:
- Features 12-point Smaller-than-standard Bolt Head
- Thick Flat Washers Distribute Optimum Clamp Load
- Ideal Use Where Space Is Minimal On Race Manifolds
- Bolts And Washers Zinc Plated For Protection
- Zinc Plated For Protection
Energy Suspension – Torsion Bar Dust Boot Set (Part No.5.13101G)
from
$9.99
Product Features:
See More
- Easy to Install
- Superior Material
- Saves Your Torsion Bar
- Lasts Longer
- Looks Great
Flowmaster Inc. – 50 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Moderate Sound (Part No.942451)
from
$154.99
The three chamber design utilizes Flowmaster’s patented Delta Flow technology along with an internal tuning chamber to reduce sound inside the vehicle. Provides the same performance and exterior tone characteristics as the two chamber, but with less interior resonance. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More
Accel – Universal Fit Graphite Suppression; Spark Plug Wire Set (Part No.8026)
from
$128.99
These ACCEL carbon and graphite core wire sets virtually eliminate RFI noise, while providing maximum conductivity for ultimate performance in any race or street application. Double silicon insulation eliminates leakage and misfire.
Product Features:
See More
Product Features:
- Heavy Duty 8.8mm Oversized Silicone Jacket
- 500 Ohms/ft. Of Resistance
- 550 Degree Double Silicone Construction
- Fiberglass Braid
- Carbon/Graphite Core
- Magnetic Suppression
- Fiberglass/Kevlar Core
- 500 Ohms Resistance
Energy Suspension – Motor Mount (Part No.5.1106G)
from
$52.99
A true performance application component for cars, trucks, hot rods and racing/competition vehicles – yet designed to be also used for street vehicles. Soft-running enough to absorb vibrations for street use yet rugged for racing use. When required- a torque resistant safety interlock design is used that is comparable in strength to those too hard-running metal mounts. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal motor mounts. The popular early style mounts for General Motors vehicles are available in either zinc or chrome metal finishes. Made of Hyper-Flex performance polyurethane. Resistant to under vehicle fluids such as: oils, coolants, road contaminants, etc.
Product Features:
See More
Product Features:
- Gains Both Performance and Longevity
- Will Handle Any and All Torque
- Out Lasts Rubber
Mr. Gasket – High Performance Thermostat (Part No.4366)
from
$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.
Product Features:
See More
Product Features:
- Opens at 160 Degrees
- Designed to Resist Large Variations of Coolant Pressure at High RPM
- Opens at Correct Temperature Consistently Regardless of Engine RPM
- For High Performance Street, Drag Race, and Oval Track
- Stainless Steel, Copper & Brass Construction – Resists Corrosion
- High Flow
Lakewood – Drag Shock-70/30:Ford/GM/Mopar (Part No.40121)
from
$104.99
The best all-round choice for vehicles with leaf or coil springs. Properly loads rear wheels to prevent over-reaction and wheel hop.
Product Features:
See More
Product Features:
- Excellent Weight Transfer
- Lets Front End Down Quickly
- Maximum Traction
- Makes Vehicle Safer
- Easier Control At End Of Track
- Better Overall Stability
Energy Suspension – Control Arm Bushing Set (Part No.5.3132R)
from
$62.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.
Product Features:
See More
Product Features:
- Maintains Better Alignment While Driving
- Full Floating and Non Binding
- Fits Into the Remaining Stock Control Arms
Mallory – Distributor Wiring Harness (Part No.29349)
B & M – Flexplate, 6 Bolt Crank for TF 727 (Part No.10230)
from
$154.99
As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1962-up TF727 transmissions and all internally balanced Chrysler, Dodge and Plymouth V8 engines with 6-bolt crankshaft flange. Features include high tensile strength steel construction to resist elongation and cracking, dual bolt pattern 10.00 or 11.125 inch converter mounting locations and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953.
Product Features:
See More
Product Features:
- NHRA/IHRA Legal For All Classes
- Includes SFI Certification Sticker
- Ideal For Street Applications
- To Extreme Duty Racing
- To High RPM Use
Energy Suspension – Strut Rod Bushing Set (Part No.5.7105G)
from
$17.99
These performance polyurethane components help reduce common wheel roll-under. This occurs when stopping abruptly, especially when using performance tires for both front of rear drive vehicles is so equipped. Replaces that original, short lived and too-soft O.E.M, rubber on front wheel drive vehicles – diminishes wheel hop and traction loss during standing start accelerations. Better maintains proper alignment under extreme conditions. Made of Energy’s Hyper-Flex performance polyurethane to add both performance and durability.
Product Features:
See More
Product Features:
- Made from HYPER-Flex Polyurethane
Mr. Gasket – Breather/Oil Filler Cap (Part No.2059)
from
$14.29
Chrome plated breather cap is ideal for race car vacuum balance systems, as well as original equipment applications with positive crankcase ventilation (PCV).
Product Features:
See More
Product Features:
- Features 1″ O.D. neck and a 5/8″ O.D. breather tube
- Breather has Metal/Foam Baffle inside and includes Grommet
- Fits all aftermarket valve covers with a 1.22″ Dia. opening
Energy Suspension – Tie Rod Dust Boot (Part No.9.13101R)
from
$9.99
Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.
Product Features:
See More
Product Features:
- Easy to Install
- Superior Material
- Saves Your Tie Rods
- Lasts Longer
- Looks Great
Mr. Gasket – Dust Cap (Part No.2485)
from
$12.09
If you have custom steel or mag wheels that are not designed without a provision for a center cap, you’re probably looking at an ugly stock dust cap in the center of your front wheels. This chrome dust cap fixes that problem, and is a direct replacement for stock cap 1.790 inches in diameter. Two per set.
Product Features:
See More
Product Features:
- Chrome Plated Steel
- Set of 2 Caps
- Easy Installation
- 2 Per Set
Accel – Module:Eliminator Replacement (Part No.2005)
from
$91.99
Put an end to high maintenance point ignition systems by utilizing a specialized electronic circuitry and an infrared signal. Stabilizes ignition timing from 1 to 10,000 RPM. Improves performance and fuel efficiency, easy to install with hand tools, reduces maintenance. It is built with the latest thermal clad based surface mount construction for maximum dependability and long life.
Product Features:
See More
Product Features:
- Most Accurate Ignition Timing System
- Improves Performance And Fuel Economy
- Easy To Install With Simple Hand Tools
- Reduced Maintenance
- Eliminates Changing Points
Hurst – Automatic Shifter, Quarter Stick (Part No.3160014)
from
$426.99
The award-winning Quarter Stick automatic shifter is designed to provide positive gear change control for street or racing transmission applications. Gated mechanism. NHRA/IHRA approved reverse lockout.
Product Features:
See More
Product Features:
- Forward and Reverse Shift Patterns
- Chrome Plated Trigger for Detent Activity
- Factory Neutral Safety Switch
- Compact And Lightweight
- Roller Detent with Shifter Pattern
Accel – Super Stock Replacement Coil for Improved Performance, Starting, and Power (Part No.8140)
from
$42.49
Excellent high performance replacement for import and domestic vehicles with canister type oil filled coil. Re-engineered windings for even higher energy output resulting in quicker starting improved throttle response and more high RPM power. Designed to work with Points style and Breakerless electronic ignition systems. Heavy duty black Alkyd tower provides in flashover in protection to primary terminals. ACCEL Yellow can. 42000 volts effective up to 6500 RPM 1.4 ohms on the primary
Product Features:
See More
Product Features:
- 42000 Volts
- Effective To 6500 RPM
- Quicker Starting
- Improved Throttle Response
- Higher RPM Power
- Can Finished In Yellow
Accel – Supercoil (Part No.140001)
from
$105.99
Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.
Product Features:
See More
Product Features:
- Oil Filled For Better Cooling
- Optimized Low Resistance
- Silicon Magnetic Steel E-Core
- Higher Energy/Voltage Outputs
- Quicker Starts
- Improved Idle Quality
- Resists Shock And Vibration
- Resists Corrosion
Energy Suspension – Sway Bar Bushing Set (Part No.5.5134G)
from
$65.99
Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.
Product Features:
See More
Product Features:
- Allows Sway Bar System to Work At 100% Efficiency
- Zerk Type Fittings
- Allows for Periodic Greasing
- Lasts Much Longer Than OEM Rubber Bushings
- Handling Characteristics Improve Dramatically
Energy Suspension – Sway Bar Bushing Set (Part No.5.5135R)
from
$65.99
Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.
Product Features:
See More
Product Features:
- Allows Sway Bar System to Work At 100% Efficiency
- Zerk Type Fittings
- Allows for Periodic Greasing
- Lasts Much Longer Than OEM Rubber Bushings
- Handling Characteristics Improve Dramatically
K&N – Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine (Part No.HP-2004)
from
$17.99
K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.
Product Features:
See More
Product Features:
- HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
- VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
- PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
- EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
- EASY TO REMOVE: Fast and easy Wrench-Off removal
- HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
- HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers
K&N – Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine (Part No.HP-1017)
from
$17.99
K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. Designed to operate with all synthetic, conventional, and blended motor oils, K&N’s pleated synthetic-blend filtration media helps to shield your engine from contaminants and ensure a consistent flow of oil. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.
Product Features:
See More
Product Features:
- Designed to allow high flow rates and a consistent flow of oil to your engine
- Pleated synthetic-blend filtration media removes most harmful contaminants
- Fast and easy Wrench-Off removal using the welded one-inch hex nut
- High capacity to withstand the service intervals recommended by vehicle manufacturers
- Heavy-duty canister for outstanding durability
- Laboratory tested to ensure excellent capacity, efficiency, and mechanical strength
- Designed to operate with all synthetic, conventional, and blended motor oils
Holley – Mechanical Fuel Pump (Part No.12-440-11)
from
$206.99
Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.
Product Features:
See More
Product Features:
- High Output Fuel Flow
- Flows 110 gph Free Flow
- Shutoff Pressure Pre-Set From 6.5 To 8 PSI
- Fuel Pressure Regulator Is Not Required
- Heavy Duty Construction For Continuous High rpm Operation
- Fuel Body Casting Can Be Rotated For Plumbing Situations
- Inlet And Outlet Tapped For 1/4 in. NPT
- Inlet/Outlet Tapped For 3/8 in. NPT
Holley – Mechanical Fuel Pump Mounting Pad Cover (Part No.12-813)
from
$17.79
Fuel pump mounting pad cover is used to cover the hole in the block when the mechanical fuel pump is removed to use an electric pump.
Product Features:
See More
Product Features:
- Mechanical Fuel Pump Mounting Pad Cover For Chrysler V-8ft.S
Flowtech – Ceramic Header (Part No.33100FLT)
from
$578.99Product Features:
- Fuel Economy From The Engine
- Leak Test For Max Performance
- Ceramic Headers
- Rust And Corrosion Resistance
- Mandrel-Formed Power Plenum
- Leakproof O-Ringed Port Seals
- Include All Mounting Hardware
Hooker Headers – Competition Header (Part No.5901HKR)
from
$289.99
LS1 full length engine swap header fits 66-72 Chevelle, El Camino, Monte Carlo and Sprint applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.
Product Features:
See More
Product Features:
- High Performance
- Affordable
- Durable 16 Gauge Material
- Welds Easier
- Lasts Longer
- Heat Cured
- High Heat Resistant
Edelbrock – Performer Carburetor #9913 750 CFM With Electric Choke, Satin Finish (Non-EGR) (Part No.9913)
from
$427.99
Product Features:
See More
- Satin Finish
- 4 Barrel
- Annular Booster Type
- Electric Choke Type
- 750 cfm Maximum Flow Rating
Edelbrock – Performer 1400 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1400)
from
$498.99
The Edelbrock 1400 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characterist
Product Features:
See More
Product Features:
- Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
- Electric Choke
- 4 Barrel Count
- Square Bore
- Electric Choke Installed from Factory
- Smooth Secondary Transition
- Includes Only Timed Vacuum Port
- Includes EGR ; Fuel Vapor Outlet
Popular 1964 Dodge Dart Performance and Racing Products Categories
1964 Dodge Dart Performance and Racing Products
You count on your 1964 Dodge Dart to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Performance and Racing Products. With 34 Performance and Racing Products ranging in price from $5.99 to $1,092.00, you’re sure to find everything you need for your 1964 Dodge Dart.
Brands matter. If you want to shop a specific Performance and Racing Products brand, we stock 12 different brands like Accel, Mr. Gasket, and Edelbrock. 1964 Dodge Dart Performance and Racing Products start as low as $5.99!
One of the best ways to find top quality OEM or aftermarket Performance and Racing Products is by asking professionals. Short of that, you can shop with confidence thanks to our 538 extensive product reviews on 1964 Dodge Dart Performance and Racing Products. Some of the top-rated Performance and Racing Products products we carry are Intake Manifold Bolts with 4.6 stars and High Perf. Full-Flow Lube Spin-on with 4.0 stars.
Did we mention you can order your Performance and Racing Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Performance and Racing Products inventory for your 1964 Dodge Dart below to get started!
Top-Rated Performance and Racing Products Brands For Your 1964 Dodge Dart
Trusted Performance and Racing Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1964 Dodge Dart running right for years to come. In our inventory you’ll find brands like Accel, Mr. Gasket, Edelbrock, and even more.
Popular Mallory Performance and Racing Products
You’ll find popular Mallory brand products across Performance Ignition Products. All are waiting to get your 1964 Dodge Dart back on the road. Some of the top-rated Mallory products in these categories are:
Top-Rated Edelbrock Performance and Racing Products
If Edelbrock are what you’re looking for, our inventory holds plenty. We stock Edelbrock brand Performance and Racing Products for your 1964 Dodge Dart, and some of our most reviewed Edelbrock parts include:
from
$428.99
(55)
Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Performance Carburetors
from
$394.99
(10)
Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
Performance Carburetors
from
$397.99
(5)
Performer Carburetor #9906 600 CFM With Electric Choke, Satin Finish (Non-EGR)
Performance Carburetors
FAQs for 1964 Dodge Dart Performance and Racing Products
What are the most purchased Performance and Racing Products for the 1964 Dodge Dart?
Out of 34 Performance and Racing Products for the 1964 Dodge Dart, the most popular in our inventory are:
from
$42.49
(54)
Super Stock Replacement Coil for Improved Performance, Starting, and Power
Performance Coils
from
$26.99
(20)
High Performance 180 Degree Thermostat for Increased Flow
Performance Engine Coolant Thermostats
What are the top-rated 1964 Dodge Dart Performance and Racing Products?
Top-rated Performance and Racing Products for your 1964 Dodge Dart based on customer reviews/ratings are:
from
$16.99
(4)
High Perf. Full-Flow Lube Spin-on
“Filter size for my boat. OMC 460. works fine. HP filters have a bypass so that clogs do not cause the engine to starve for oil… important for HP eng”
from
$154.99
(3)
50 Series Muffler, 2in Offset Inlet 2in Center Outlet, Non-Reversible, Moderate Sound
“Muffler was delivered on time and fit my 1994 Ford Ranger perfectly, and was easy to install (once I got the old one off). The whole muffler felt ‘sol”
