1964 Dodge 880 Performance and Racing Products

Essential Performance and Racing Products for 1964 Dodge 880s

Edelbrock – Cylinder Head Gasket Set for Chrysler (Part No.7325)

Cylinder Head Gasket Set for Chrysler

from

$72.99
Product Features:
  • Cylinder Head Gasket
  • 1958-1979 361-383-400-413-426
  • Not For Hemi
See More

Accel – Supercoil (Part No.140001)

Supercoil

from

$105.99
Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

Product Features:
  • Oil Filled For Better Cooling
  • Optimized Low Resistance
  • Silicon Magnetic Steel E-Core
  • Higher Energy/Voltage Outputs
  • Quicker Starts
  • Improved Idle Quality
  • Resists Shock And Vibration
  • Resists Corrosion
See More

Mallory – Unilite Breakerless Ignition Conversion Kit (Part No.503M)

Unilite Breakerless Ignition Conversion Kit

from

$176.99
Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:
  • Easy Installation
  • Improved Fuel Economy
  • Reduced Maintenance
  • Accurate Timing
  • Improved Performance
  • Provides A Simple Conversion
  • No Moving Parts To Wear Out
See More

K&N – Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration (Part No.E-1540)

Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration

from

$149.99
K&N performance High-Flow Air Filters are engineered to improve engine performance. Unlike disposable paper filters which must be frequently replaced, K&N Air Filters are washable, reusable, and engineered to last for the life of your vehicle or outdoor power small engine. Engineered to fit easily into your factory air box, installation can be completed in a matter of minutes! K&N develops and tests each product on the world┐s toughest race tracks, so we can bring the highest level of performance to your daily driving. Join the millions of customers who have saved money and improved vehicle performance by upgrading to K&N filtration.

Product Features:
  • ENGINEERED POWER: State-of-the-art air filter media is designed to increase horsepower and acceleration as well as improve overall engine performance
  • RUGGED CONSTRUCTION: K&N Air Filters are manufactured with durable, premium materials and state-of-the-art construction methods to last a lifetime
  • 4 LAYERS OF PROTECTION: Multiple layers of premium cotton gauze treated with a specially-designed tacking agent work together to create an intricate mesh of engine filter media that is designed to block and trap harmful contaminants
  • CLEAN ONCE EVERY 5 YEARS: Engine air filter only needs cleaning every 75,000 miles under normal highway driving conditions (based on the average miles driven per year of 15,000 miles)
  • ULTIMATE LONGEVITY: No-hassle lifetime warranty on stock replacement K&N air filters- limitations apply
  • EASY INSTALLATION: K&N Air Filters are pre-treated and ready to drop into your factory air box- they are one of the easiest and most cost-effective vehicle upgrades for quick performance gains
  • ECO-FRIENDLY: Using a washable, reusable engine air filter helps reduce replacement air filter waste- a K&N air filter is designed to last longer than 10 or more disposable filters
  • MADE IN USA: K&N Air Filters are proudly made in the USA for trusted quality & reliability
See More

Edelbrock – Signature Series Valve Covers: Big Block Chrysler 383-440, Chrome Steel (Part No.4491)

Signature Series Valve Covers: Big Block Chrysler 383-440, Chrome Steel

from

$81.99
The Edelbrock #4491 Signature Series Valve Covers are designed for Chrysler 361-383-400-413-426-440 V8 ’58-79 applications. Engineered for function and styled for great looks, Signature Series valve covers have stock-style breather baffles that prevent oil passage to the PCV valve. These quality valve covers accept all emissions equipment, including PCV valve holes. Rubber grommets for the breather and PCV valve holes are included. Matching breathers sold separately.

Product Features:
  • Big Block Chrysler 383-440
  • Short
  • Chrome Steel
  • Set Of Two
  • Rubber Grommets For Breather
See More

Mr. Gasket – Remote Oil Filter Kit (Part No.7682)

Remote Oil Filter Kit

from

$97.99
This kit relocates the oil filter for quick, clean and easy access and increased filtering. It is complete with precision die cast aluminum by-pass, filter brackets and all high pressure connectors.

Product Features:
  • Relocate oil filter to an easy access location
See More

Edelbrock – Sure Seat Valve Springs for Chrysler 383-400-413-440 V8 1969-79 (Part No.5792)

Sure Seat Valve Springs for Chrysler 383-400-413-440 V8 1969-79

from

$141.99
Product Features:
  • Non-Rotator Type
  • 1.550 in. Outer Diameter
  • .190 Wire Size
  • Single Coil Spring Type
  • Set of 16
See More

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1808)

PERFORMANCE OIL PAN GASKET SET

from

$17.29
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Dust Cap (Part No.2485)

Dust Cap

from

$12.09
If you have custom steel or mag wheels that are not designed without a provision for a center cap, you’re probably looking at an ugly stock dust cap in the center of your front wheels. This chrome dust cap fixes that problem, and is a direct replacement for stock cap 1.790 inches in diameter. Two per set.

Product Features:
  • Chrome Plated Steel
  • Set of 2 Caps
  • Easy Installation
  • 2 Per Set
See More

Mr. Gasket – High Performance Thermostat (Part No.4367)

High Performance Thermostat

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens at 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

Edelbrock – Performer RPM 2 Carb/Plate Nitrous Systems Square-Bore Carbs (100-400+ Hp) (Part No.70082)

Performer RPM 2 Carb/Plate Nitrous Systems Square-Bore Carbs (100-400+ Hp)

from

$1114.99


Product Features:
  • Designed For Carbureted V8 Engines
  • Enhanced Flow Capacity
  • Add Power In Stages
  • Softens The Hit Of The Nitrous System
See More

Mr. Gasket – Advance And Retard Cam Bushings (Part No.85)

Advance And Retard Cam Bushings

from

$42.49
With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:
  • Advance the cam for increased torque and horsepower
  • Tune your powerband for more end torque or increase top end horsepower
  • Includes (4) offset bushings and (1) 0 degree bushing
  • Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
  • Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
  • Increase Top-End Horsepower
See More

Spectre – Water Neck; Chrysler (Part No.4739)

Water Neck; Chrysler

from

$23.79
Spectre’s Chrysler water neck fits 1964 and later Chrysler V8 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes bolts.

Product Features:
  • Fits 1964 and later Chrysler V8 engines
  • Includes bolts
  • Chrome plated
  • Easy to install
  • O-ring/gasket not included
See More

Mallory – Distributor Wiring Harness (Part No.29349)

Distributor Wiring Harness

from

$30.49


Product Features:
  • Service Part
  • Makes Connections Quick And Easy
See More

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9734)

Performer Series Retainer (Qty 16)

from

$91.99
Product Features:
  • Use W/ Valve Springs Part #5792
  • Use W/ Locks Part #9612
  • 1.50 in. Outside Diameter
  • Steel Material
  • Black Oxide Finish
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1414)

Exhaust Manifold Gasket Set

from

$42.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Rear Main Seal Gasket (Part No.1968)

Rear Main Seal Gasket

from

$42.99
This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:
  • Repairs That Leaky Rear Main Sail
  • Silicone Rubber to Withstand Extreme Engine Oil Temperatures
  • Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
  • Injection Molded for Precise Fit
See More

Edelbrock – Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1405)

Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet

from

$394.99
The Edelbrock 1405 Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1405 Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Manual Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Powertrax – No-Slip Traction System (Part No.9203822705)

No-Slip Traction System

from

$527.99
For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.
  • Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.
  • Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.
  • Powertrax® = Extreme Traction Systems!
  • See More

    Mr. Gasket – Intake Manifold Bolt Set – Chevrolet Small Block – Socket Head 3/8"-16 X 1" Bolts & Washers (Part No.956G)

    Intake Manifold Bolt Set - Chevrolet Small Block - Socket Head 3/8"-16 X 1" Bolts & Washers

    from

    $17.49
    These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

    Product Features:
    • Zinc plated to resist corrosion and provide a clean professional appearance
    • Made from Grade 5 steel for strength and durability
    • Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
    • Allen (socket) Head
    • Zinc Plated For Protection
    See More

    Mr. Gasket – Precision Timing Tape (Part No.1593)

    Precision Timing Tape

    from

    $18.99
    Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

    Product Features:
    • 7 1¿4″ diameter
    • 7 1┐4″ diameter
    • 383 thru 440 cu. in.
    • Increased Performance
    • Set Valve Lash At Proper Time
    See More

    Holley – Mechanical Fuel Pump Mounting Pad Cover (Part No.12-813)

    Mechanical Fuel Pump Mounting Pad Cover

    from

    $17.79
    Fuel pump mounting pad cover is used to cover the hole in the block when the mechanical fuel pump is removed to use an electric pump.

    Product Features:
    • Mechanical Fuel Pump Mounting Pad Cover For Chrysler V-8ft.S
    See More

    FEL-PRO Performance – Lower Intake Manifold Gasket Set: 4 Piece Set (Part No.1216)

    Lower Intake Manifold Gasket Set: 4 Piece Set

    from

    $27.49
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
    • SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
    • ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
    • REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
    • EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
    See More

    Edelbrock – Performer RPM 2 Carb/Plate Nitrous Systems 4500 Series Carbs (200-400+ Hp) (Part No.70081)

    Performer RPM 2 Carb/Plate Nitrous Systems 4500 Series Carbs (200-400+ Hp)

    from

    $830.99


    Product Features:
    • Designed For Carbureted V8 Engines
    • Enhanced Flow Capacity
    • Softens The Hit Of The Nitrous System
    • Simple To Install
    See More

    Edelbrock – Valve Cover Gasket Set for Chrysler (Part No.7591)

    Valve Cover Gasket Set for Chrysler

    from

    $44.99
    Product Features:
    • 0.1875 in. Thickness
    • Core-Reinforced-Composite Material
    • For Late Model 1963-1980 BB Chrysler W/ 6-Bolt Valve Covers
    • Set of 2
    • Made In The USA
    See More

    Hays – Comp/Trk Clutch Kit-1O.5 Chry (Part No.85-301)

    Comp/Trk Clutch Kit-1O.5 Chry

    from

    $601.99
    High burst strength woven lining to withstand heat and higher engine RPM. Heavy-duty sprung hub assembly to allow smooth engagement and steady torque transfer without chatter. Recommended for high horsepower street vehicles in addition to occasional drag strip use.

    Product Features:
    • Built As Matched Assembly
    • Exceptional Performance
    • Exceptional Durability
    • Long Term Dependability
    See More

    Edelbrock – Water Pump #8814 For 1958-79 BB Chrysler 361-440, Standard Rotation, Satin (Part No.8814)

    Water Pump #8814 For 1958-79 BB Chrysler 361-440, Standard Rotation, Satin

    from

    $237.99
    Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

    Product Features:
    • Maximum Cooling for Street and Racing Engines
    • Internal Passages Are Balanced for Maximum Flow
    • Impeller is Larger than Others For Max Pressure
    • Impeller Vanes Dramatically Increase Flow Rates
    • Equal Distribution to Both Sides of Block
    • Only Flows in One-Direction for Optimum Efficiency
    See More

    Hurst – Automatic Shifter, Quarter Stick (Part No.3160009)

    Automatic Shifter, Quarter Stick

    from

    $426.99
    The award-winning Quarter Stick automatic shifter is designed to provide positive gear change control for street or racing transmission applications. Gated mechanism. NHRA/IHRA approved reverse lockout.

    Product Features:
    • Forward and Reverse Shift Patterns
    • Chrome Plated Trigger for Detent Activity
    • Factory Neutral Safety Switch
    • Compact And Lightweight
    • Roller Detent with Shifter Pattern
    See More

    Upgrade your 1964 Dodge 880 with Top-Quality Performance and Racing Products

    When it comes to maintaining or upgrading your 1964 Dodge 880, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Dodge or enhancing its overall performance, Performance and Racing Products are key to keeping your 880 functioning at its best. At Advance Auto Parts, we offer a wide selection of 59 Performance and Racing Products for the 1964 Dodge 880, designed to meet your needs without breaking the bank. From Performance Oil Filter replacements to Performance Engines upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

    Affordable Prices and Wide Selection

    Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1964 Dodge 880 at great prices. Our Performance and Racing Products inventory for this model ranges from just $12.09 to $2,198.99, with an average price of $353.08. Our 59 Performance and Racing Products in stock come from 13 trusted brands, so you’re sure to find the right part for your 1964 Dodge 880 without overspending.

    Top Brands and High Customer Satisfaction

    Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1964 Dodge 880, we stock popular OEM and aftermarket Performance and Racing Products from top names like Accel, Edelbrock, Mr. Gasket, and more. Accel Performance and Racing Products start at just $42.49 and boast an impressive 4 stars average rating from customers. Edelbrock and Mr. Gasket also bring quality to the table, with Performance and Racing Products available starting at $12.09, and at an average 4 stars rating. With 253 customer reviews and counting, our 1964 Dodge 880 Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.

    Explore Related Parts and More

    While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Fluids and Chemicals and more to make sure your 1964 Dodge 880 is always ready to roll. We’re committed to providing you with everything you need to keep your 880 in top shape, all in one place. Start shopping confidently below for your 1964 Dodge 880!

    Best-Selling Performance Oil Filters for 1964 Dodge 880s

    Enhance the driving experience in your Dodge with 1 quality Performance Oil Filter components, starting at $97.99.

    Mr. Gasket – Remote Oil Filter Kit (Part No.7682)

    Remote Oil Filter Kit

    from

    $97.99
    This kit relocates the oil filter for quick, clean and easy access and increased filtering. It is complete with precision die cast aluminum by-pass, filter brackets and all high pressure connectors.

    Product Features:
    • Relocate oil filter to an easy access location
    See More

    Most Popular 1964 Dodge 880 Performance Engines

    Customize your Dodge with 19 Performance Engines products like Performance Engine Intake Manifold Gaskets, Performance Engine Cylinder Head Gaskets, and Performance Intake Manifolds, all priced under $2,198.99.

    Mr. Gasket – Valve Cover Gasket Set (Part No.379)

    Valve Cover Gasket Set

    from

    $36.49
    Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

    Product Features:
    • Manufactured from high-density cork/rubber blend gasket material
    • Provides excellent sealing and durability
    • For OE replacement, high performance street, drag race and oval track use
    See More

    Competition Cams – Engine Valve Spring Kit (Part No.911-16)

    Engine Valve Spring Kit

    from

    $759.99
    Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.O.D. Dia. 1 I.D. Dia. 2 Damper Seat Load Open Load Coil Bind Rate (Lbs./In.) Titanium Retainer Steel Retainer Cup Seat Shims 1.524 1.110 Y 122 @ 1.900 309 @ 1.400 1.200 373 721, 732 1732, 741 4779* 4757

    Product Features:
    • Seat pressure: 122 lbs. @ 1.900″, Open Pressure: 309 lbs. @ 1.400″
    • O.D.: 1.524″, I.D.: 1.110″
    • Single valve springs with damper
    See More

    Edelbrock – Cylinder Head Gasket Set for Chrysler (Part No.7325)

    Cylinder Head Gasket Set for Chrysler

    from

    $72.99
    Product Features:
    • Cylinder Head Gasket
    • 1958-1979 361-383-400-413-426
    • Not For Hemi
    See More

    Spectre – Water Neck; Chrysler (Part No.4739)

    Water Neck; Chrysler

    from

    $23.79
    Spectre’s Chrysler water neck fits 1964 and later Chrysler V8 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes bolts.

    Product Features:
    • Fits 1964 and later Chrysler V8 engines
    • Includes bolts
    • Chrome plated
    • Easy to install
    • O-ring/gasket not included
    See More

    FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1808)

    PERFORMANCE OIL PAN GASKET SET

    from

    $17.29
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
    • With steel core to provide ultimate excellent blowout resistance.
    • Not intended for use in emission controlled vehicles.
    See More

    Mr. Gasket – High Performance Thermostat (Part No.4367)

    High Performance Thermostat

    from

    $26.99
    Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

    Product Features:
    • Opens at 180 Degrees
    • Designed to Resist Large Variations of Coolant Pressure at High RPM
    • Opens at Correct Temperature Consistently Regardless of Engine RPM
    • For High Performance Street, Drag Race, and Oval Track
    • Copper & Brass Construction – Resists Corrosion
    • High Flow
    See More

    FEL-PRO Performance – Lower Intake Manifold Gasket Set: 8 Piece Set (Part No.1214)

    Lower Intake Manifold Gasket Set: 8 Piece Set

    from

    $46.99
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
    • SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
    • ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
    • REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
    • EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
    See More

    Mr. Gasket – Intake Manifold Bolt Set – Chevrolet Small Block – Socket Head 3/8"-16 X 1" Bolts & Washers (Part No.956G)

    Intake Manifold Bolt Set - Chevrolet Small Block - Socket Head 3/8"-16 X 1" Bolts & Washers

    from

    $17.49
    These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

    Product Features:
    • Zinc plated to resist corrosion and provide a clean professional appearance
    • Made from Grade 5 steel for strength and durability
    • Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
    • Allen (socket) Head
    • Zinc Plated For Protection
    See More

    FEL-PRO Performance – Lower Intake Manifold Gasket Set: 4 Piece Set (Part No.1216)

    Lower Intake Manifold Gasket Set: 4 Piece Set

    from

    $27.49
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
    • SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
    • ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
    • REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
    • EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
    See More

    FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2947)

    Engine Crankshaft Seal Kit

    from

    $48.99
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
    • Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
    • Not intended for use in emission controlled vehicles.
    See More

    Edelbrock – Valve Cover Gasket Set for Chrysler (Part No.7591)

    Valve Cover Gasket Set for Chrysler

    from

    $44.99
    Product Features:
    • 0.1875 in. Thickness
    • Core-Reinforced-Composite Material
    • For Late Model 1963-1980 BB Chrysler W/ 6-Bolt Valve Covers
    • Set of 2
    • Made In The USA
    See More

    Mr. Gasket – Precision Timing Tape (Part No.1593)

    Precision Timing Tape

    from

    $18.99
    Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

    Product Features:
    • 7 1¿4″ diameter
    • 7 1┐4″ diameter
    • 383 thru 440 cu. in.
    • Increased Performance
    • Set Valve Lash At Proper Time
    See More

    Edelbrock – Big-Block Chrysler E-Street Cylinder Heads 84cc (Part No.5093)

    Big-Block Chrysler E-Street Cylinder Heads 84cc

    from

    $2198.99
    The Edelbrock #5093 E-Street cylinder heads are designed for use with 1961-1979 Chrysler 361-440 c.i.d. Wedge engine applications. The Edelbrock E-Street cylinder heads offer American made quality and affordable performance. E-Street cylinder heads featur

    Product Features:
    • Complete Pair For Hydraulic Flat Tappet
    • 84cc Combustion Chamber Volume
    • 210cc Intake/70cc Exhaust Runner Volume
    • 2.14 in. Intake/1.81 in. Exhaust Valve Diameter
    • 0.625 in. Deck Thickness
    See More

    Edelbrock – Water Pump #8814 For 1958-79 BB Chrysler 361-440, Standard Rotation, Satin (Part No.8814)

    Water Pump #8814 For 1958-79 BB Chrysler 361-440, Standard Rotation, Satin

    from

    $237.99
    Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

    Product Features:
    • Maximum Cooling for Street and Racing Engines
    • Internal Passages Are Balanced for Maximum Flow
    • Impeller is Larger than Others For Max Pressure
    • Impeller Vanes Dramatically Increase Flow Rates
    • Equal Distribution to Both Sides of Block
    • Only Flows in One-Direction for Optimum Efficiency
    See More

    Edelbrock – Sure Seat Valve Springs for Chrysler 383-400-413-440 V8 1969-79 (Part No.5792)

    Sure Seat Valve Springs for Chrysler 383-400-413-440 V8 1969-79

    from

    $141.99
    Product Features:
    • Non-Rotator Type
    • 1.550 in. Outer Diameter
    • .190 Wire Size
    • Single Coil Spring Type
    • Set of 16
    See More

    Edelbrock – Performer Series Retainer (Qty 16) (Part No.9734)

    Performer Series Retainer (Qty 16)

    from

    $91.99
    Product Features:
    • Use W/ Valve Springs Part #5792
    • Use W/ Locks Part #9612
    • 1.50 in. Outside Diameter
    • Steel Material
    • Black Oxide Finish
    See More

    Mr. Gasket – Advance And Retard Cam Bushings (Part No.85)

    Advance And Retard Cam Bushings

    from

    $42.49
    With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

    Product Features:
    • Advance the cam for increased torque and horsepower
    • Tune your powerband for more end torque or increase top end horsepower
    • Includes (4) offset bushings and (1) 0 degree bushing
    • Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
    • Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
    • Increase Top-End Horsepower
    See More

    Mr. Gasket – Super Intake Manifold Bolts (Part No.6080)

    Super Intake Manifold Bolts

    from

    $27.49
    These grade 5 hex head bolts are black coated plated for protection and appearance. Hardened flat washers provide uniform torque and prevent galling on aluminum manifolds.

    Product Features:
    • Assures Accurate Torque App
    • Prevents Galling Manifold
    • Grade 5 Material
    • Black Oxide Coasted
    See More

    FEL-PRO Performance – Performance Valve Cover Gasket Set (Part No.1611)

    Performance Valve Cover Gasket Set

    from

    $20.29
    Fel-Pro® Performance Gaskets deliver reliable sealing under grueling racing conditions.

    Product Features:
    • Blue Stripe® performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
    • Not intended for use in emission controlled vehicles.
    See More

    Top Picks for 1964 Dodge 880 Performance Exhaust Products

    Upgrade Dodge 880s with top-quality Performance Exhaust Products parts, including 2 OEM and aftermarket selections for your 1964 model.

    FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1414)

    Exhaust Manifold Gasket Set

    from

    $42.99
    Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

    Product Features:
    • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
    • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
    • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
    • Slotted bolt holes allow for easier header installation.
    • Not intended for use in emission controlled vehicles.
    See More

    Mr. Gasket – Copper Seal; Exhaust Gasket Set (Part No.7167)

    Copper Seal; Exhaust Gasket Set

    from

    $60.29
    Copperseal exhaust gaskets are unique gaskets made from .043 inch solid copper. They feature an embossed O-ring design for a leak proof seal. They won’t shrink, deteriorate or blowout. Header bolts stay tight. Ideal for motor homes and towing.

    Product Features:
    • Will Not Shrink/Deteriorate
    • Creates A Tight Leak Proof Seal
    • Helps Lower Under hood Temps
    • Seals Irregular Surfaces
    • Seals Slightly Damaged Surface
    • Ideal For Tow Vehicles
    • Ideal For Motor Homes
    See More

    In-Demand Performance Fuel Systems for 1964 Dodge 880s

    Select from 8 premium Performance Fuel Systems parts for your 1964 Dodge 880, with prices ranging from $17.79 to $541.99.

    Edelbrock – CARBURETOR (Part No.14054)

    CARBURETOR

    from

    $488.99
    Product Features:
    • EnduraShine Finish
    • GM/AMC-Style Throttle Linkage
    • Can Add Electric Choke PN[1478]
    • Easy Tuning with 2-Piece Design
    • Smooth Secondary Transition
    • Both Timed and Full Vacuum Ports
    • Includes PCV Outlet
    See More

    Edelbrock – Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1406)

    Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet

    from

    $428.99
    The Edelbrock 1406 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1406 Performer Series 600 CFM electric choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

    Product Features:
    • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
    • Electric Choke
    • 4 Barrel Count
    • Square Bore
    • Smooth Secondary Transition
    • Both Timed and Full Vacuum Ports
    • Includes PCV Outlet
    See More

    Edelbrock – Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1405)

    Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet

    from

    $394.99
    The Edelbrock 1405 Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1405 Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

    Product Features:
    • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
    • Manual Choke
    • 4 Barrel Count
    • Square Bore
    • Smooth Secondary Transition
    • Both Timed and Full Vacuum Ports
    • Includes PCV Outlet
    See More

    Edelbrock – Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1407)

    Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet

    from

    $451.99
    The Edelbrock 1407 Performer Series 750 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristic

    Product Features:
    • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
    • Manual Choke
    • 4 Barrel Count
    • Square Bore
    • Smooth Secondary Transition
    • Both Timed and Full Vacuum Ports
    • Includes PCV Outlet
    See More

    Holley – Mechanical Fuel Pump Mounting Pad Cover (Part No.12-813)

    Mechanical Fuel Pump Mounting Pad Cover

    from

    $17.79
    Fuel pump mounting pad cover is used to cover the hole in the block when the mechanical fuel pump is removed to use an electric pump.

    Product Features:
    • Mechanical Fuel Pump Mounting Pad Cover For Chrysler V-8ft.S
    See More

    Edelbrock – CARBURETOR (Part No.14064)

    CARBURETOR

    from

    $541.99
    Product Features:
    • EnduraShine Finish
    • GM/AMC-Style Throttle Linkage
    • Electric Choke Installed from Factory
    • Easy Tuning with 2-Piece Design
    • Smooth Secondary Transition
    • Both Timed and Full Vacuum Ports
    • Includes PCV Outlet
    See More

    Edelbrock – Reman Thunder AVS Carb #18129 800 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.18129)

    Reman Thunder AVS Carb #18129 800 CFM With Manual Choke, Satin Finish (Non-EGR)

    from

    $413.99
    Product Features:
    • Satin Finish
    • 4 Barrel
    • Aluminum Body Material
    • Manual Choke Type
    • 800 cfm Maximum Flow Rating
    See More

    Edelbrock – Performer Carburetor #9907 750 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.9907)

    Performer Carburetor #9907 750 CFM With Manual Choke, Satin Finish (Non-EGR)

    from

    $407.99
    Product Features:
    • Satin Finish
    • 4 Barrel
    • Annular Booster Type
    • Manual Choke Type
    • 750 cfm Maximum Flow Rating
    See More

    Most Sold 1964 Dodge 880 Performance Air Filters

    Explore our best-selling Dodge parts for the 1964 880 among 1 OEM and aftermarket options starting from $149.99.

    K&N – Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration (Part No.E-1540)

    Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration

    from

    $149.99
    K&N performance High-Flow Air Filters are engineered to improve engine performance. Unlike disposable paper filters which must be frequently replaced, K&N Air Filters are washable, reusable, and engineered to last for the life of your vehicle or outdoor power small engine. Engineered to fit easily into your factory air box, installation can be completed in a matter of minutes! K&N develops and tests each product on the world┐s toughest race tracks, so we can bring the highest level of performance to your daily driving. Join the millions of customers who have saved money and improved vehicle performance by upgrading to K&N filtration.

    Product Features:
    • ENGINEERED POWER: State-of-the-art air filter media is designed to increase horsepower and acceleration as well as improve overall engine performance
    • RUGGED CONSTRUCTION: K&N Air Filters are manufactured with durable, premium materials and state-of-the-art construction methods to last a lifetime
    • 4 LAYERS OF PROTECTION: Multiple layers of premium cotton gauze treated with a specially-designed tacking agent work together to create an intricate mesh of engine filter media that is designed to block and trap harmful contaminants
    • CLEAN ONCE EVERY 5 YEARS: Engine air filter only needs cleaning every 75,000 miles under normal highway driving conditions (based on the average miles driven per year of 15,000 miles)
    • ULTIMATE LONGEVITY: No-hassle lifetime warranty on stock replacement K&N air filters- limitations apply
    • EASY INSTALLATION: K&N Air Filters are pre-treated and ready to drop into your factory air box- they are one of the easiest and most cost-effective vehicle upgrades for quick performance gains
    • ECO-FRIENDLY: Using a washable, reusable engine air filter helps reduce replacement air filter waste- a K&N air filter is designed to last longer than 10 or more disposable filters
    • MADE IN USA: K&N Air Filters are proudly made in the USA for trusted quality & reliability
    See More

    Top-Rated Performance and Racing Products Brands For Your 1964 Dodge 880

    Shop for the best-rated brands offering Performance and Racing Products and other products for your 1964 Dodge 880s. Below you’ll find some of our best rated Performance and Racing Products from Accel, Edelbrock, and Mr. Gasket, and more. Performance and Racing Products from these brands that fit a 1964 880 start at just $12.09 and are rated as high as 4 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.

    Popular Accel 1964 Dodge 880 Performance and Racing Products

    When it comes to maintaining or upgrading your 1964 Dodge 880, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. Accel ticks all of those boxes. We offer a wide selection of Accel Performance and Racing Products, specifically designed for the 1964 Dodge 880. With over 3 Accel brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $42.49, with an average price of just $80.16. Plus, with over 54 customer reviews and an average rating of 4 stars, you can trust that our Accel Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

    Supercoil
    from
    $105.99
    This product is not rated

    Supercoil

    “”

    Module:Eliminator Replacement
    from
    $91.99
    This product is not rated

    Module:Eliminator Replacement

    “”

    Popular Edelbrock 1964 Dodge 880 Performance and Racing Products

    Edelbrock auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1964 Dodge 880 owner should feel confident when installing genuine Edelbrock parts in their vehicle. To ensure the best fit and performance for your 1964 880, Advance Auto Parts carries a full inventory of 26 Edelbrock Performance and Racing Products. Plus you will be keeping your Dodge in peak condition while saving money because prices on these Edelbrock Performance and Racing Products range from $44.99 to $2,198.99, plus, with more than 77 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.

    Big-Block Chrysler E-Street Cylinder Heads 84cc
    from
    $2198.99
    This product is not rated

    Big-Block Chrysler E-Street Cylinder Heads 84cc

    “”

    Performer RPM 2 Carb/Plate Nitrous Systems for Dominator
    from
    $1138.99
    This product is not rated

    Performer RPM 2 Carb/Plate Nitrous Systems for Dominator

    “”

    Valve Cover Gasket Set for Chrysler
    from
    $44.99
    This product is not rated

    Valve Cover Gasket Set for Chrysler

    “”

    FAQs for 1964 Dodge 880 Performance and Racing Products

    Which Performance and Racing Products are best-sellers for 1964 Dodge 880s?

    Out of 59 Performance and Racing Products that fit 1964 Dodge 880s, the following parts are the top sellers:

    What’s the price range for 1964 Dodge 880 Performance and Racing Products?

    Performance and Racing Product prices for the 1964 Dodge 880 start at $12.09 and go up to $2,198.99 for the most premium parts.

    What’s the average price of a Performance and Racing Product for a 1964 Dodge 880?

    The average price for Performance and Racing Products for the 1964 Dodge 880 is $353.08. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.

    Does Advance Auto Parts sell Performance and Racing Products for other Dodge 880 model years?

    Yes, we currently carry Performance and Racing Products for 3 model years of Dodge 880s between 1962 and 1965. Performance and Racing Products are bought most frequently for the following model years: 1965, 1963, and 1962.

    What are the cheapest Performance and Racing Products for my 1964 Dodge 880?

    The cheapest 1964 Dodge 880 Performance and Racing Products we carry in stock are:

    What are the top-rated Performance and Racing Products that fit the 1964 Dodge 880?

    Out of 253 reviews by customers, our 1964 Dodge 880 Performance and Racing Products have an average customer rating of . These are some of the highest-rated Performance and Racing Product types for the 1964 Dodge 880 and their top-rated products:

    What types of Performance and Racing Products do you sell for my 1964 Dodge 880?

    As of 2/5/25, these are some of the most in-demand types of Performance and Racing Products for a 1964 Dodge 880:

    Can I get help with 1964 Dodge 880 Performance and Racing Product orders?

    Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Dodge Performance and Racing Products and more.

    What is your return policy for Dodge 880 Performance and Racing Products?

    Advance Auto Parts keeps returns simple. For new Dodge 880 Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.