from

$6.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$946.99

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000! This locker also fits 9.5″ & 10″ dropouts.

Product Features:

Fits Ford 9″ with 35 spline axles
Patented internal design reduces common locker failures
8620 internals for added strength
Assembled in the USA

from

$55.99

7.25″ Ford & 6.75″ Ford pinion seal.Yukon Mighty seal.

Product Features:

Pinion seal
Fits Ford 6.75″ and 7.25″

from

$272.99

Product Features:

R&P FORD 8″ – 3.40 RATIO

from

$20.29

Product Features:

Brand may vary by location

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$188.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M86610 race
All steel construction

from

$26.49

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

from

$121.99

Yukon short yoke for Ford 9″ HD with 28 spline axles and a 1330 U/joint size. 4″ length. 3.625″ snap ring span, 1.125″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 9″
28 spline
1330 u-joint size
3.625″ snap ring span
1.125″ cap diameter
Outside snap ring design
U-bolt style

from

$309.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits Ford 9″ with LM104911 carrier bearing
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pilot bearing, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve eliminator, thread locker, marking compound with brush and gasket.

from

$14.99

O-ring for 9″ Ford.Yukon Mighty seal.

Product Features:

Pinion support o-ring
Fits Ford 9″

from

$13.99

8″ Ford pilot bearing retainer.

Product Features:

Pilot bearing retainer for Ford 8″

from

$6.99

Pinion support bolt for 8″ and 9″ Ford.

Product Features:

Pinion support bolt for Ford 8″ and 9″
3/8″ x 24 thread
1.0″ long

from

$149.99

Product Features:

FULL SPOOL FORD 9″ 35 SPL. LGT WGT

from

$225.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Ford 9″ with Daytona pinion support
Included are pinion bearings and races, pinion seal, crush sleeve eliminator , complete pinion shim kit, and marking compound with brush.

from

$5.99

Product Features:

Copper washer
Fits Ford 8″ and 9″

from

$198.99

Product Features:

Spider gear kit
Fits Ford 8″ and 9″ 28 spline open differential
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$8.99

Product Features:

Trac Loc spring for Ford 8″ and 9″

from

$279.99

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses carrier bearings & races with an I.D. of 1.780″ and an O.D. of 3.062″. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pilot bearing, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

Fits Ford 9″ with LM603011 carrier races and Daytona pinion support
Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, pilot bearing, marking compound and brush.

from

$7.99

Pinion nut for Ford 7.5″, 8″, 8.8″, 9 3/8″ & 9″. 1 1/6″ socket, 3/4″ x 20 thread.

Product Features:

Pinion nut for Ford 7.5″, 8″ and 9″
3/4″ x 20 thread
1 1/6″ socket

from

$34.99

The tremendous shock loads generated at launch by most any drag racing vehicle equipped with today sticky tire compounds or the acceleration and deceleration of oval track cars put considerable strain on the ring gear. For this reason, the fastener experts at ARP have developed the Pro Series ring gear bolts. they are forged from premium grade 8740 chrome moly steel and are heat treated to a nominal rating of 200,000 PSI tensile strength. Specially hardened, precision ground washers are included where required. Available to fit most any ring gear setup ranging from popular 9 Inch Ford GM 10 and 12 bolt rear ends to the beefy strange differentials found in top fuel and funny car applications.

Product Features:

Forged From Premium Grade 8740 Chrome Moly Steel
Heat Treated
Nominally Rated At 200,000 PSI Tensile Strength
Specially Hardened, Precision Ground Washers
0.95″ Underhead Length
200,000 PSI
Sold As A Set

from

$5.99

Product Features:

Side gear thrust washer for Ford 8″, Ford 9″ and AMC Model 20
0.030″ thick

from

$37.49

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$21.99

8.75″ Chrysler & 9″ Ford preload shim kit.

Product Features:

Preload shim kit for Ford 9″ and Chrysler 8.75″ with ’41’ and ’42’ case housing

from

$4.99

Pinion gear thrust washer for 8″ and 9″ Ford, Model 20, and 7.25″ Chrysler.

Product Features:

Pinion gear thrust washer for Ford 8″, Ford 9″ and Chrysler 7.25″

from

$789.99

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Trac Loc uses a nodular case, billet side hat, and forged internals for higher strength than stock Trac-Locs. The units use composite clutches for high performance and long life. All units are Rebuildable. Yukon offers a one year warranty against manufacturing defects.

Product Features:

Fits Ford 9″ with 28 spline axles
Trac Loc positraction
Clutch style positraction
Street design
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA