1963 Chevrolet K20 Pickup Flywheels

The ring gear has teeth which engage with the starter motor allowing the engine to crank over and start. Repeated engagement with the starter results in worn or broken ring gear teeth. Once this is diagnosed, the ring gear must be replaced. ATP ring gears are designed to fit and function just like the original part to ensure durability and long life.

Product Features:

• Manufactured to meet or exceed original equipment specs
• Eliminates grinding from damaged teeth
• Increases starter drive life

The ring gear has teeth which engage with the starter motor allowing the engine to crank over and start. Repeated engagement with the starter results in worn or broken ring gear teeth. Once this is diagnosed, the ring gear must be replaced. ATP ring gears are designed to fit and function just like the original part to ensure durability and long life.

Product Features:

• Manufactured to meet or exceed original equipment specs
• Eliminates grinding from damaged teeth
• Increases starter drive life

Hays aluminum flywheels are manufactured from certified billet material that will not break up under the stress of high RPM and severe punishment of racing. Features replaceable steel surface insert. Precision balanced to either neutral (internal) or Detroit (external) specifications. Meets SFI specification 1.1 for racing.

Product Features:

• Certified Billet Material
• Borg and Beck Clutch Pattern
• Long-Style Clutch Pattern
• Ring Gear Securely Mounted To Prevent Spinning

Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA. Limited five year Manufacturer’s warranty.

Product Features:

• Use With Chevy Big Block
• OE Style
• Direct Fit
• Limited 5 Year Warranty

Vehicles with manual transmissions have a flywheel. The Flywheel is where the clutch assembly is mounted. It provides a smooth friction surface for the clutch disk. Flywheels also have teeth for the starter. Flywheels can crack, break, or break starter teeth. Once a damaged flywheel is diagnosed, a new replacement is the best route to go. ATP flywheels provide fit and function just like the original part to ensure durability and long life.

Product Features:

• Manufactured to meet or exceed original equipment specs
• No resurfacing required
• Improves performance

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1955 to 1985 small block Chevy V8 engines (internally balanced) with two piece rear main seal. Features include high tensile strength steel construction to resist elongation and cracking, 10.75 inch bolt pattern, 153 tooth ring gear with double-sided welds for added strength and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953. Compatible with Powerglide, TH350, TH400 and TH700R4 automatic transmissions.

Product Features:

• NHRA/IHRA Legal For All Classes
• Includes SFI Certification Sticker
• Ideal For Street Applications
• To Extreme Duty Racing
• To High RPM Use

AT HD FLEX PLATE

Vehicles with automatic transmissions have a flex plate. Flex plates connect the engine And transmission. Most flex plates are made of a thick piece of sheet metal with bolt holes for the torque converter And teeth for the starter. The job of a flex plate is to allow for expansion of the torque converter as engine RPM increases. The constant expansion And contraction of a flex plate over time can result cracks And/or shearing of the flex plate. A damaged flex plate can create serious (expensive) damage. Broken flex plates can not be repaired, they must be replaced. ATP flex plates are made of high quality steel And contain the correct bolt hole spacing And ring gear teeth just like the original part to ensure long life And durability

Product Features:

• Balanced to factory specs
• Fit and function like the original parts
• Restores normal operation

Vehicles with automatic transmissions have a flex plate. Flex plates connect the engine And transmission. Most flex plates are made of a thick piece of sheet metal with bolt holes for the torque converter And teeth for the starter. The job of a flex plate is to allow for expansion of the torque converter as engine RPM increases. The constant expansion And contraction of a flex plate over time can result cracks And/or shearing of the flex plate. A damaged flex plate can create serious (expensive) damage. Broken flex plates can not be repaired, they must be replaced. ATP flex plates are made of high quality steel And contain the correct bolt hole spacing And ring gear teeth just like the original part to ensure long life And durability

Product Features:

• Balanced to factory specs
• Fit and function like the original parts
• Restores normal operation

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1955-85 GM small block (internally balanced) V8 engines along with 4.3L V6 engines. Also fits 1990 and earlier GM big block (internally balanced) V8 engines with two piece rear main seal. Features include high tensile strength steel construction to resist elongation and cracking, dual bolt pattern 10.75 or 11.5 inch converter mounting locations, 168 tooth ring gear with double-sided welds for added strength and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953. Compatible with Powerglide, TH350, TH400 and TH700R4 automatic transmissions.

Product Features:

• NHRA/IHRA Legal For All Classes
• Includes SFI Certification Sticker
• Ideal For Street Applications
• To Extreme Duty Racing
• To High RPM Use

M/T FLYWHEEL

Constructed of thicker than stock steel plate to withstand the stress of high stall speed converters and high RPM engine. Zinc dichromate plated to resist rust and corrosion. Meets SFI specification 29.1 for racing.

Product Features:

• Thicker Than Stock Steel Plate
• Ring Gear Securely Welded
• Dual Bolt Patterns
• Zinc-Dichromate Plated To Resist Corrosion
• Withstands High Torque and RPM

Constructed of thicker than stock steel plate to withstand the stress of high stall speed converters and high RPM engine. Zinc dichromate plated to resist rust and corrosion. Meets SFI specification 29.1 for racing.

Product Features:

• Thicker Than Stock Steel Plate
• Ring Gear Securely Welded
• Dual Bolt Patterns
• Zinc-Dichromate Plated To Resist Corrosion
• Withstands High Torque and RPM

Vehicles with automatic transmissions have a flex plate. The flex plates connects the engine and transmission. Most flex plates are made of a thick piece of sheet metal with bolt holes for the torque converter and teeth for the starter. The job of a flex plate is to allow for expansion of the torque converter as engine RPM increases. The constant expansion and contraction of a flex plate over time can result cracks and/or shearing of the flex plate. A damaged flex plate can create serious (expensive) damage. Broken flex plates can not be repaired, they must be replaced. ATP flex plates are made of high quality steel and contain the correct bolt hole spacing and ring gear teeth just like the original part to ensure long life and durability

Product Features:

• Balanced to factory specs
• Fit and function like the original parts
• Restores normal operation

Hays aluminum flywheels are manufactured from certified billet material that will not break up under the stress of high RPM and severe punishment of racing. Features replaceable steel surface insert. Precision balanced to either neutral (internal) or Detroit (external) specifications. Meets SFI specification 1.1 for racing.

Product Features:

• Certified Billet Material
• Borg and Beck Clutch Pattern
• Long-Style Clutch Pattern
• Ring Gear Securely Mounted To Prevent Spinning

ATP Flywheel Shim

FLYWHEEL SHIM

FLYWHEEL SHIM

FLYWHEEL SHIM