1961 Mercury Monterey Performance Engines

Our unique Multi-Layered steel head gasket embossment formation process optimizes the embossment radius, reduces stress points, enhances gasket conformability, and provides uniform clamp load distribution. This all results in superior surface contact between block and cylinder head. All head gasket layers/spacers go through an additional process to significantly reduce forming induced stress. Advantages are reduced brittleness in material, increased flexibility and deformation retention. This stabilizes the gasket, resulting in reduced cylinder bore distortion and improved combustion seal fro the extreme cylinder pressures found in high compression, supercharged and turbocharged applications. A proprietary polymer coating ensures the micro-seal of engine coolant and oil fluids.brbrA typical MLS head gasket requires a smoother (30Ra) surface finish than composite head gaskets. Mr. Gasket’s proprietary polymer coating will seal a surface finish twice as rough (60Ra) as a typical MLS head gasket. For high performance street, drag race and oval track use. Mr. Gasket provides a Limited Lifetime Warranty for MLS cylinder head gaskets.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

The Edelbrock No: 7365 head gaskets provide the best sealing solution and are matched to Edelbrock cylinder heads for optimal performance. Edelbrock relies on industry leading head gasket manufactures to ensure our head gasket sets will provide the best fit and sealing properties when used with Edelbrock aluminum cylinder heads. Edelbrock head gaskets are manufactured from high-density materials and feature a superior design that performs under pressure and provides a long-lasting seal, without re-torqueing.

“Edelbrock part No: 7328 head gasket is intended for Ford 351 Cleveland engines. This gasket comes as a set and has a 4.080″” bore size, .038″” compressed thickness and 8.1 cc volume.”

The Edelbrock valve cover gaskets No: 7568 provide excellent sealing integrity and conformability for easy installation. The multi-layer construction has two highly compressible, high rubber content, fiber-reinforced outside layers which are chemically bonded to a high strength composite core. This unique core-reinforced construction has a radial strength to resist high-vacuum or blow-out conditions. Edelbrock valve cover gaskets are an Edelbrock product.

Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

Edelbrock Performer 400 Intake Manifold for 1971-82 Ford 351/M400, 2171.

Holley EFI MFLD KIT FORD 351W HI-RAM 95MM EFI, 300-241.

Weiand X-CELerator Intake Manifold, 7516.

3) For off-highway use, non-EGR 4V system with an Edelbrock #8714 4V spacer.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

HYDRAULIC – Big Mutha’ Thumpr Retro-Fit: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. Comes complete with front & rear manifold end seals. For original equipment replacement, high performance street, drag race and oval track. Fits all Ford 351C – 2V or 351 Cleveland 2-Barrel heads.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

The Edelbrock No: 5792 Sure Seat Valve Spring for Chrysler 383-400-413-440 V8 1969-79 O.E Cast iron cylinder heads are made of highest quality spring wire and precision wound to close tolerances, our Sure Seat Valve Spring sets are for use on original equipment heads when installing Edelbrock Performer-Plus, Performer RPM and Torker-Plus camshafts. These are the same high-performance springs used on Edelbrock Performer and RPM cylinder heads. For camshaft warranty compliance, use only the springs recommended by Edelbrock for each camshaft application.

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

“This Beehive Valve Spring Kit for LS engines is designed for hydraulic roller cams and includes carefully matched Beehive Springs, steel retainers, locks, seals and spring seats. With a .625″” maximum lift, these Beehive Valve Springs deliver increased valve train stability and a much lighter valve train. This is achieved with less spring pressure for better valve control and reduced weight of both the spring and retainer. The unique Beehive shape handles valve train stress more efficiently to eliminate damaging harmonics and increases high RPM horsepower and durability. The oval/multi-arc wire shape places the maximum area of the wire at the point of highest stress to handle valve train stress more efficiently and allow better heat dissipation for longer life.Kit Includes:26918-16 Beehive Valve Springs774-16 Steel Retainers623-16 7° Steel Valve Locks511-16 Valve Seals4705-16 Spring Seats”

FE FORD HYDRAULIC CAM AND LIFTER KIT – High Energy: Good upgrade for factory performance cams in 390-428. Noticeable idle.

“Edelbrock Performer-Plus Camshaft No: 2106 is designed for 352-428 Ford V8 engines and produce optimum torque from the low-end to the mid-range. Performer-Plus camshafts should be matched with Performer manifolds for vehicles operating from off-idle to 5500 rpm. The Performer-Plus No: 2106 is a smooth idling cam for daily drivers, trucks, vans, RVs and 4x4s. You can expect a major improvement in throttle response and torque. In the manifold section you’ll find torque graphs showing the power gains from Performer manifolds and Performer-Plus cams. All camshafts include flat tappet lifters (except for cams designed for use with stock roller lifters), assembly lube and instructions. This cam produced 410 Ft Lbs of Torque when paired with Performer 390 intake manifold No: 2105 and stock cylinder heads. Will not work in 427 side-oilers. Camshaft specifications: – Intake duration: 194 Degrees – Exhaust duration: 204 Degrees – Intake lift: .460″” – Exhaust lift: .480″” – Lobe separation: 110 Degree – Intake Center Line: 105 Degree – Vacuum: 16″””

An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.