1960 Jeep FA-134 Belts and Hoses
More 1960 Jeep FA-134 Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 1960 Jeep FA-134, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 1960 Jeep FA-134 Belts and Hoses
Gates – Vulco-Flex« II Flexible Coolant Hose (Part No.25480)
from
$25.49
Gates Vulco-Flex(R) II hose will bend in almost any direction. It easily replicates the angles and planes of a wide variety of expensive original equipment coolant hose, for quick, easy replacement.
Product Features:
See More
Product Features:
- Improved sealing surface for greater leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimum inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature Range: up to +257 Deg. F (+125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Vulco-Flex« II Flexible Coolant Hose (Part No.25478)
from
$18.49
Gates Vulco-Flex(R) II hose will bend in almost any direction. It easily replicates the angles and planes of a wide variety of expensive original equipment coolant hose, for quick, easy replacement.
Product Features:
See More
Product Features:
- Improved sealing surface for greater leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimum inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature Range: up to +257 Deg. F (+125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Premium Molded Coolant Hose (Part No.20993)
from
$49.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)
from
$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)
from
$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
Gates – Automotive XL« High Capacity V-Belt (Part No.9480)
from
$31.99
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
- Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
- Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
- Resists oil, heat, ozone, weather and aging for improved belt life
- Meets or exceeds SAE J636C specifications
Gates – Green Stripe« Truck & Bus Series V-Belt (Part No.TR22425)
from
$26.99
Specifically designed for heavy-duty truck, bus and off-road equipment applications. Absorbs normal shock loads without damage to the belt.
Product Features:
See More
Product Features:
- Molded notches reduce bending stress, especially on small diameter pulleys, while dissipating heat
- High modulus, high strength tensile cord
- Oil and heat-resistant construction throughout
- Meets SAE J636b and SAE J637 specifications
- Meets RMA oil and heat resistant standards and static conductivity requirements
- NOTE: Some sizes available as Gates PowerBand joined V-belts
Popular 1960 Jeep FA-134 Belts and Hoses Categories
1960 Jeep FA-134 Belts and Hoses
You count on your 1960 Jeep FA-134 to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 7 Belts and Hoses ranging in price from $18.49 to $79.99, you’re sure to find everything you need for your 1960 Jeep FA-134.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 2 different brands like Imperial and Gates. 1960 Jeep FA-134 Belts and Hoses start as low as $18.49!
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 1960 Jeep FA-134 below to get started!
FAQs for 1960 Jeep FA-134 Belts and Hoses
What are the most purchased Belts and Hoses for the 1960 Jeep FA-134?
Out of 7 Belts and Hoses for the 1960 Jeep FA-134, the most popular in our inventory are:
