1960 Chevrolet Suburban Performance and Racing Products
More 1960 Chevrolet Suburban Performance and Racing Products Categories
If you’re looking for an original Performance and Racing Products replacement for a 1960 Chevrolet Suburban, you can search through our selection below. You’ll also find aftermarket and OEM Performance and Racing Products to meet your needs.
Essential 1960 Chevrolet Suburban Performance and Racing Products
Mr. Gasket – Intake Manifold Bolts (Part No.6091)
from
$32.09
These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.
Product Features:
See More
Product Features:
- Features 12-point Smaller-than-standard Bolt Head
- Thick Flat Washers Distribute Optimum Clamp Load
- Ideal Use Where Space Is Minimal On Race Manifolds
- Bolts And Washers Zinc Plated For Protection
- Zinc Plated For Protection
Mr. Gasket – Rear Main Seal Gasket (Part No.1960)
from
$23.99
This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.
Product Features:
See More
Product Features:
- Repairs That Leaky Rear Main Sail
- Silicone Rubber to Withstand Extreme Engine Oil Temperatures
- Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
- Injection Molded for Precise Fit
B & M – Flexplate, SFI 29.1 Approved, Fits 168-Tooth, 2-Piece Rear Main Seal, Chevy V8 (Part No.20230)
from
$154.99
As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1955-85 GM small block (internally balanced) V8 engines along with 4.3L V6 engines. Also fits 1990 and earlier GM big block (internally balanced) V8 engines with two piece rear main seal. Features include high tensile strength steel construction to resist elongation and cracking, dual bolt pattern 10.75 or 11.5 inch converter mounting locations, 168 tooth ring gear with double-sided welds for added strength and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953. Compatible with Powerglide, TH350, TH400 and TH700R4 automatic transmissions.
Product Features:
See More
Product Features:
- NHRA/IHRA Legal For All Classes
- Includes SFI Certification Sticker
- Ideal For Street Applications
- To Extreme Duty Racing
- To High RPM Use
FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1010)
from
$39.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
- NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
- SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
- STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
- DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
Competition Cams – CAM & LIFTER KIT, SBC 260H HIGH ENERGY HYD 1 KT (Part No.CL12-206-2)
from
$323.99
Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering
Product Features:
See More
Product Features:
- Good blend of efficiency and performance.
- Perfect choice for performance street rebuilds.
- Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.
Mr. Gasket – Water Pump (Part No.7011)
from
$279.99
This high flow pump is chrome plated cast iron and will keep your engine cool while looking cool.
Product Features:
See More
Product Features:
- Chrome Plated Cast Iron
- Heavy Duty Shaft & Bearings
- Dual Pulley Bolt Pattern
- Small Block Chevy – Short Style
- Tested for reliability
Edelbrock – Street Tunnel Ram Small Block Chevy Intake Manifold (Part No.7110)
from
$631.99
For 3500 to 7500 PRM. Use where low-end torque is not a prime factor. Great for engines with slightly modified heads. HEI ignition will not clear manifold. Street machines, street rods, pro-street and marine.
Product Features:
See More
Product Features:
- For 3500 to 7500 RPM
- Use Where Low-End Torque is Not a Prime Factor
- Great For Engines w/Slightly Modified Heads
- Top Has Vacuum Outlet for Power Brakes
- Will Accept Forward and Sideways Mounted Carbs
- Carburetor Center-to-Center Dimensions 8.875 in
- HEI Ignition Will Not Clear Manifold
- For Street Mach.; Street Rods; Pro-Street; Marine
Mr. Gasket – Thermocap Radiator Cap (Part No.2470R)
from
$48.09
The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.
Product Features:
See More
Product Features:
- Indicates coolant temperature
- Helps prevent coolant injuries
- Fahrenheit and centigrade readings
- Color-coded temperature ranges
- Integrated coolant reclamation valve
- Improves under-hood appearance
- Chromed crown with a colored trim ring
FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1640)
from
$22.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
- Not intended for use in emission controlled vehicles.
Competition Cams – Set of 16 Single Springs w/ 1.254" O.D., 1.254" I.D., 1.700" Installed Height (Part No.981-16)
from
$126.99
Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.
Product Features:
See More
Product Features:
- Seat pressure: 105 lbs. @ 1.700″, Open Pressure: 273 lbs. @ 1.250″
- O.D.: 1.254″, I.D.: .880″
- Single valve springs with damper
- Approximately .490″ max lift at recommended installed height
FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1819)
from
$31.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
- With steel core to provide ultimate excellent blowout resistance.
- Not intended for use in emission controlled vehicles.
FEL-PRO Performance – Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set (Part No.1802)
from
$25.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
- With steel core to provide ultimate excellent blowout resistance.
- Not intended for use in emission controlled vehicles.
Mallory – Unilite Ignition Module (Part No.605)
from
$85.29
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.
Product Features:
See More
Product Features:
- Service Part
- No Moving Parts To Wear Out
- Self Contained Unit
- Can Drive OEM
- Can Drive High Performance Ignition Coils
Mallory – Distributor Wiring Harness (Part No.29349)
Edelbrock – Performer RPM Series fuel pump for SBC and W Series Chevy (Part No.1721)
from
$168.99Product Features:
- Unique Valve Design
- Improves Flow Quantity/Quality
- Supports Engines Up To 550 HP
- Hi-Vol 0.375 in. NPT Inlet/Outlet
- Produces 6 psi
- Gasoline Or Mixed Fuels Only
Holley – Mechanical Fuel Pump (Part No.12-327-13)
from
$165.99
Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.
Product Features:
See More
Product Features:
- High Output Fuel Flow
- Flows 130 gph Free Flow
- Shutoff Pressure Pre-Set From 7.5 To 9 PSI
- Fuel Pressure Regulator Required Recommend P/N 12-704
- Heavy Duty Construction For Continuous High rpm Operation
- Redesigned High Flow Valves Ensure Adequate Fuel Delivery
- Fuel Body Casting Can Be Rotated For Plumbing Situations
- Inlet And Outlet Tapped For 3/8 in. NPT
Mr. Gasket – Header Bolt Set (Part No.2210G)
from
$41.99
Made of high quality stainless steel. These bolts will brighten up your hot rod, or improve the looks of your race car.
Product Features:
See More
Product Features:
- Bright Ball Burnish Finish
- Made From 304 Stainless
- Compact Hex Head Is Ideal Where Space Is Limited
- 12 Per Set
- Resist corrosion and provides a clean professional appearance
Spectre – SBC Alt Bracket W/ Bolts (Part No.42283)
from
$15.99
This Spectre Alternator Bracket is a mount designed to fit 1969-1975 Chevrolet 265-400 Small Block engines with a short water pump with headers. Featuring a triple chrome-plated finish and high quality steel construction, this part is a replacement that mounts on the driver’s side. Intended to be used in conjunction with part number 42273 to mount the alternator, this bracket features a custom design for show quality appearances.
Product Features:
See More
Product Features:
- Fits Small Block Chevy 265-400 engines from 1969 to 1975 with headers and a short water pump
- Manufactured from high quality steel
- Designed for driver side mounting
- Features a triple chrome-plated finish
- Intended for use with part number 42273
Mr. Gasket – Oil Pan (Part No.5415)
from
$329.99
This fully polished, finned aluminum oil pan is die-cast for a perfect fit. 5 quart capacity. Drain plug & bolts included.
Product Features:
See More
Product Features:
- Die Cast Aluminum w/ Finned Bottom
- Polished
- Includes Drain Plug and Mounting Bolts
- 5 Quart Capacity
Spectre – Aluminum Oil Pan SBC 55-79 (Part No.4987)
from
$337.99
This Spectre polished aluminum oil pan is designed to fit 1955-’79 small block Chevrolet 283-350 engines with a driver’s side dipstick (except 1962-’67 Chevrolet II and Corvette with stock exhaust). This oil pan is made from a heavy die-cast polished aluminum featuring a finned diamond design. The stock oil capacity is maintained at 4 quarts and uses a 1975 and later gasket with thick front seal. The required mounting fasteners are included.
Product Features:
See More
Product Features:
- Stock 4 quart capacity
- Polished die-cast aluminum
- Finned diamond design finish
- Includes mounting fasteners
Mr. Gasket – Performance Exhaust Gasket Set for Enhanced Sealing and Durability (Part No.150B)
from
$20.99
Mr. Gasket Performance exhaust gasket material is a heavy duty material, .062 inch thick, consisting of an acrylic binder system to resist high temperature. This material is made for sealing exhaust applications. Provides excellent sealing and durability.
Product Features:
See More
Product Features:
- Manufactured from high-temperature acrylic blend exhaust material
- Provides excellent sealing and durability
- Can be trimmed if necessary for modified port applications
- For OE replacement, high performance street, drag race and oval track use
- Resists Deteriorating
- Provides Excellent Torque Retention
Flowtech – Real-Seal; Header Gasket (Part No.99150AFLT)
from
$85.39Product Features:
- Water/Weather Resistant
- Re-Useable
- Will Not Burn Or Blow Out
- Suitable For Port-Matching
- Made In USA
Competition Cams – High Energy/Marine 212/212 Hydraulic Flat Cam for Chevrolet Small Block (Part No.12-206-2)
from
$284.99
HYDRAULIC – High Energy: Vans, pickups, 4WD and towing, in 350c.i., good idle, strong mid-range torque. OR High Energy Marine: Single or dual engine with inboard/outboard drive for ski and economy.
Product Features:
See More
Product Features:
- HYDRAULIC – High Energy: Vans, pickups, 4WD and towing, in 350c.i., good idle, strong mid-range torque. OR High Energy Marine: Single or dual engine with inboard/outboard drive for ski and economy.
- 260/260 Advertised Duration, 212/212 Duration @ .050″, .440″/.440″ Lift, 110 Lobe Separation
- Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.
Competition Cams – CAMSHAFT, SBC 249 XTREME ENERGY COMPUTER CONTROLLED HYDRAULIC 1 EA (Part No.12-249-4)
from
$276.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts, the Xtreme Energy grind family offers gains in torque and horsepower while still delivering adequate vacuum for power brakes and other vacuum dependent accessories. Xtreme Energy camshafts work great in carbureted applications, but offer the best performance with aftermarket intake manifolds, lower gear ratios, headers and free flowing exhaust.
Product Features:
See More
Product Features:
- HYDRAULIC – Xtreme Energy Computer Controlled: Great in throttle body, crossfire or carbureted engine and 305 TPI.
- 249/260 Advertised Duration, 206/212 Duration @ .050″, .434″/.444″ Lift, 112 Lobe Separation
- Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
- Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
Edelbrock – Front Timing Cover Gasket Set #6997 For Small-Block Chevy, With Front Seal (Part No.6997)
from
$17.99
Product Features:
See More
- For Small-Block Chevy
- One Piece Configuration
- Includes Front Cover Gasket & Front Seal
- Includes Necessary Gaskets & Crankshaft Oil Seal
- For Replacement Or Installation
FEL-PRO Performance – Engine Timing Cover Gasket (Part No.2335)
from
$20.29
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Steel core gasket construction
- Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Lts Throttle Cable Brkt Chev (Part No.9885)
from
$14.99
The throttle cable bracket is designed for small block Chevy engines thru 1979 and is to be used in conjunction with the kick down cable Pn9886 for the Turbo 350 transmission. The throttle cable bracket mounts on the intake manifold and will hold cables with round or square mounts. It has a 2 inch adjustable range and is finished off in a beautiful chrome plating.
Product Features:
See More
Product Features:
- 2 in. adjustable range
- Includes necessary hardware
- Chrome plated
- Individually packaged
Popular 1960 Chevrolet Suburban Performance and Racing Products Categories
1960 Chevrolet Suburban Performance and Racing Products
You count on your 1960 Chevrolet Suburban to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Performance and Racing Products. With 41 Performance and Racing Products ranging in price from $14.99 to $999.99, you’re sure to find everything you need for your 1960 Chevrolet Suburban.
Brands matter. If you want to shop a specific Performance and Racing Products brand, we stock 8 different brands like Edelbrock, FEL-PRO Performance, and Mr. Gasket. 1960 Chevrolet Suburban Performance and Racing Products start as low as $14.99!
One of the best ways to find top quality OEM or aftermarket Performance and Racing Products is by asking professionals. Short of that, you can shop with confidence thanks to our 39 extensive product reviews on 1960 Chevrolet Suburban Performance and Racing Products. Some of the top-rated Performance and Racing Products products we carry are Intake Manifold Bolts with 4.6 stars and Unilite Ignition Module with 5.0 stars.
Did we mention you can order your Performance and Racing Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Performance and Racing Products inventory for your 1960 Chevrolet Suburban below to get started!
Top-Rated Performance and Racing Products Brands For Your 1960 Chevrolet Suburban
Trusted Performance and Racing Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1960 Chevrolet Suburban running right for years to come. In our inventory you’ll find brands like Edelbrock, FEL-PRO Performance, Mr. Gasket, and even more.
Popular Flowtech Performance and Racing Products
You’ll find popular Flowtech brand products across Performance Exhaust Products. All are waiting to get your 1960 Chevrolet Suburban back on the road. Some of the top-rated Flowtech products in these categories are:
Top-Rated Edelbrock Performance and Racing Products
If Edelbrock are what you’re looking for, our inventory holds plenty. We stock Edelbrock brand Performance and Racing Products for your 1960 Chevrolet Suburban, and some of our most reviewed Edelbrock parts include:
from
$195.99
(7)
Performer EPS Intake Manifold for 1955-86 Small-Block Chevy
Performance Intake Manifolds
FAQs for 1960 Chevrolet Suburban Performance and Racing Products
What are the most purchased Performance and Racing Products for the 1960 Chevrolet Suburban?
Out of 41 Performance and Racing Products for the 1960 Chevrolet Suburban, the most popular in our inventory are:
from
$39.49
(1)
Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts
Performance Engine Cylinder Head Gaskets
from
$52.99
(1)
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
Performance Engine Cylinder Head Gaskets
What are the top-rated 1960 Chevrolet Suburban Performance and Racing Products?
Top-rated Performance and Racing Products for your 1960 Chevrolet Suburban based on customer reviews/ratings are:
from
$85.29
(3)
Unilite Ignition Module
“I like the Unilite product because it is so small and compact compared to the HEI stuff I normally use. If you are restricted on space Its a great pro”
