1959 Chevrolet Corvette Performance Engines

Edelbrock part No. 2701 Performer EPS intake manifold is designed for 1986 and earlier 262-400 cubic-inch Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent throttle response. With that the Edelbrock Performer EPS intake manifold has a runner design that’s “tuned” for peak torque at 3500 rpm on a 350-inch engine making it ideal for power from off-idle to 5500 rpm. Dyno tests showed gains of 5 hp and 9 ft-lbs. of torque over the Edelbrock Performer manifold No. 2101 on a 350 Chevy. From 3000 to 4500 rpm, the power increases averaged 5+ ft-lbs. of torque for more performance where you need it most. PLEASE NOTE: Will not fit under stock Corvette hood!

Product Features:

• Maximizes Performance with Edelbrock Carburetors
• Runners Tuned to Match Square Bore Carburetor
• Maximizes Peak Torque Around 3500 RPM
• Excellent Throttle Response and Mid-Range Power
• For Idle to 5500 RPM Street-Driven Performance
• Dual-Plane Low-Rise Intake w/180 deg. Firing Order
• Prod. +5 HP and +9 ft/lbs. of Torque Over PN[2101]
• PLEASE NOTE: Will not fit under stock Corvette hood!

Product Features:

• For Idle to 5500 RPM Street-Driven Performance
• Dual-Plane Low-Rise Intake w/180 Deg Firing Order
• Patented Runner Design Ensures Broad Torque Curve
• Excellent Throttle Response and Mid-Range Power
• 50-State Street Legal if Correct Carburetor Used
• Accepts Late-Model Choke; Waterneck; and HEI
• Accepts A/C And Alternator
• Accepts Exhaust Heated Chokes

2500-6500 RPM high-performance street engines. Single-plane low-rise intake good for high RPM. Ideal for applications with limited hood clearance. For top-end HP and adequate throttle response. Not for mileage or emissions applications. For trucks or vans use PN(2701) instead. Not for LT1 or Chevy bowtie heads. Not for 1987 and later stock aluminum heads. Available in cast or polished.

Product Features:

• 2500 to 6500 RPM High Performance Street Engines
• Single-Plane Low-Rise Intake Good for High RPM
• Ideal for Applications with Limited Hood Clearance
• For Top-End HP and Adequate Throttle Response
• Not for Mileage or Emissions Applications
• For Trucks or Vans Use PN[2701] Instead
• Not for LT1 or Chevy Bowtie Heads
• Not for 1987 and Later Stock Aluminum Heads

Product Features:

• Designed for 1500 to 5500 RPM Performance
• Low Profile for Hood Clearance on Most Vehicles
• Air-Conditioning/Front Oil Tube Bosses Included
• Stock Alternator Brackets Do Not Fit
• Use Edelbrock Fuel Line Kit PN[8088] w/Our Carbs
• Carburetor Center-to-Center Dimensions = 6-7/16 in
• Use Edelbrock Linkage Kit PN[7094] w/Our Carbs
• Best Matched with Edelbrock 500 cfm Carburetors

Edelbrock part #2703 Performer EPS intake manifold is designed for 1986 and earlier 262-400 cubic-inch Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent thro

Product Features:

• Idle-5500 RPM Range
• Dual Plane Type-4150 Style Flange
• 3.74 in. Front Height, 4.27 in. Center Height, 4.8 in. Rear Height
• Satin Finish
• Non-EGR W/ Oil Fill Tube

Product Features:

• Great For Street Machines/Street Rods/Muscle Cars
• Two Piece Design
• Individual D-Shaped Runners
• Optimized For Broad Power Range/Large Plenum Area
• Can Be Used For Blow-Through Superchargers
• Fully CNC Machined For A Perfect Fit
• No Exhaust Crossover

Edelbrock part #75013 RPM Air-Gap RPM intake manifold is designed for 1955-86 262-400 c.i.d. Chevrolet V8’s. The award-winning RPM Air-Gap intake manifold incorporates the same race-winning technology that’s used on our Victor Series competition intakes.

Product Features:

• 1500-6500 RPM Range
• Dual Plane Type-4150 Style Flange
• 4.2 in. Front Height, 4.72 in. Center Height, 5.25 in. Rear Height
• Black Powder Coated Finish
• Non-EGR

Edelbrock part #5418 C-357-B Triple-Deuce intake manifold is designed for 1955-86 262-400 c.i.d. small-block Chevys, this manifold has a balanced 180-degree firing order port runner arrangement. It contains an exhaust gas heat crossover and offers excelle

Product Features:

• Idle-5500 RPM Range
• Dual Plane Type 6-Pack Style Flange
• 3.77 in. Front Height, 4.35 in. Center Height, 4.88 in. Rear Height
• Satin Finish
• Non-EGR

Product Features:

• Designed For Today’s Larger Cubic Inch Big Block
• Perfect For Hard Core Drag Racers
• Permanent Mold Casting Process
• For Lighter And More Consistent Castings
• Dyno Proven To Make 17hp More Than Competitors

Product Features:

• Designed For Today’s Larger Cubic Inch Big Block
• Perfect For Hard Core Drag Racers
• Permanent Mold Casting Process
• For Lighter And More Consistent Castings
• Dyno Proven To Make 17hp More Than Competitors

Product Features:

• High Rise/Dual Plane Design For Maximum Torque
• Fully CNC Machined For A Perfect Fit
• Square Bore Carburetor Flange
• Exhaust Crossover For Improved Street Drivability
• Permanent Mold Casting Process
• Lighter/Smoother/Better Looking
• More Consistent Castings

Product Features:

• 2000-6500 RPM Power Band
• Single Plane/Open Plenum Design
• No Provision For Divorced Or Hot Air Choke
• Square Flange Carburetor Mounting

Product Features:

• Clean Positive Seal
• Embossed Silicone Bead Surrounding The Port
• Matched To Manifolds And Cylinder Heads

Ultra-Seal is Mr. Gasket premium valve cover gasket material. It’s manufactured from a high density cork and rubber blend with a black latex coat applied to the outside to help seal minor flange irregularites and eliminate oil leakage. It creates a positive seal by controlled swelling of the gasket material when exposed to hot oil. For original equipment replacement, high performance street, drag race and oval track use. Sold as a pair. These gaskets are an extra thick .312 inch which can help with valvetrain clearance.

Product Features:

• Manufactured from high-density cork /rubber blend gasket material
• A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage
• Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil
• For OE replacement, high performance street, drag race and oval track
• An extra thick .312″ which can help with valvetrain clearance

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
• Not intended for use in emission controlled vehicles.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Die cut silicone rubber gaskets conform to out-of-flat covers
• Great for on-again/off-again situations
• Not intended for use in emission controlled vehicles.

Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.brbrThese gaskets are .312 inch thick. That’s substantially thicker than stock which can allow for additional valve train clearance. brbrFits Chevrolet 262,265,267,283,307,327,350,400 Gen I Small Block with Perimeter Bolt Valve Covers.

Product Features:

• Provides Excellent Flange Sealing And Durability
• For High-Performance Street, Drag Race & Oval Track Use

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 180 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens at 160 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully opens at Correct Temperature Consistently Regardless of engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 195 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
• NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
• SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
• STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
• DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
• Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
• Raises combustion sealing force to roughly three times that of standard head gaskets.
• Steel wire rings for the greatest combustion seal strength.
• Not intended for use in emission controlled vehicles.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
• NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
• SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
• STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
• DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

Our unique Multi-Layered steel head gasket embossment formation process optimizes the embossment radius, reduces stress points, enhances gasket conformability, and provides uniform clamp load distribution. This all results in superior surface contact between block and cylinder head. All head gasket layers/spacers go through an additional process to significantly reduce forming induced stress. Advantages are reduced brittleness in material, increased flexibility and deformation retention. This stabilizes the gasket, resulting in reduced cylinder bore distortion and improved combustion seal fro the extreme cylinder pressures found in high compression, supercharged and turbocharged applications. A proprietary polymer coating ensures the micro-seal of engine coolant and oil fluids.brbrA typical MLS head gasket requires a smoother (30Ra) surface finish than composite head gaskets. Mr. Gasket’s proprietary polymer coating will seal a surface finish twice as rough (60Ra) as a typical MLS head gasket. For high performance street, drag race and oval track use.

Product Features:

• Gasket bore – 4.060″ Thickness – .040″
• Manufactured from 3-layer premium grade stainless steel and state of the art laser cutting
• Optimized sealing embossments seals extreme cylinder pressure
• Provides excellent stability and reduces cylinder bore distortion.
• Proprietary polymer coating ensures the micro seal of engine coolant and oil fluids.
• Ideal for supercharged, turbocharged, nitrous oxide and extreme compression ratio engines
• For high-performance street, drag race and oval track use

Mr. Gasket Steel Shim Cylinder Head Gaskets are for high performance street machines, drag racing and oval track racing. With today’s extreme compression ratios you need stronger more durable gaskets. Mr. Gasket steel shim gaskets are made from .020 inch steel shim stock which is thinner than most composite gaskets increasing engine compression. Stress formed embossments will seal the extreme cylinder pressure.

Product Features:

• Manufactured from .020″ steel shim stock.
• Thinner than composition head gaskets – increases engine compression.
• Stress formed embossments seal extreme cylinder pressures.
• For high performance street, drag race and oval track use.