1955 Packard Car Parts

Holley’s new 0-80457SA is constructed from aluminum which compared to its zinc counterpart equates to a weight savings of 40%! Holley’s aluminum 0-80457SA will hold its shine longer and also can be hand polished for a custom look! Its 600 CFM of airflow,

Product Features:

• Vibratory Polished For Good Looks

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

• Vibratory Polished For Good Looks
• Optimized Street Calibration That Works Out Of The Box
• Factory Preset Electric Choke For Easy Startups
• Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
• No Unnecessary Trips Back To The Parts Store
• Limited Lifetime Warranty
• 100% Wet Flow Tested By Holley Technicians
• Arrives Ready To Run

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

• Vibratory Polished For Good Looks
• Optimized Street Calibration That Works Out Of The Box
• Factory Preset Electric Choke For Easy Startups
• Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
• No Unnecessary Trips Back To The Parts Store
• Limited Lifetime Warranty
• 100% Wet Flow Tested By Holley Technicians
• Arrives Ready To Run

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

• Vibratory Polished For Good Looks
• Optimized Street Calibration That Works Out Of The Box
• Factory Preset Electric Choke For Easy Startups
• Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
• No Unnecessary Trips Back To The Parts Store
• Limited Lifetime Warranty
• 100% Wet-Flow Tested To Assure It Arrives Ready To Run
• Street Ready; Out Of The Box

The Novita 550 is a thermal turn signal flasher that operates at 12V and feature 3 terminals. This flasher uses heat which is generated by electricity, to bend spring steel internally which causes the flasher to operate.

Product Features:

• For 12 Volt Applications
• Compatible with incandescent bulbs only.
• 3 Terminals
• Handles up to 4 incandescent lamps

Product Features:

• The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
• Improper installation will void your warranty and may result in poor performance and engine or vehicle damage

Product Features:

• The Edelbrock #12380 Metering Block gasket is made of black nitrile material and will ensure a leak-free seal from your Carb to the metering block.
• The Edelbrock #12380 Metering Block gasket will fit 4150 &4160 Carburetors.
• These will not work with accelerator pump transfer tubes.

The Ultra Double Pumper Carburetors feature all aluminum construction and are equipped with metering blocks and a base plate made from 6061-T6 billet aluminum. Three different anodized color options (Red, Blue, or Black) allow for a personalized look while maintaining the ultra high strength and durability you get from billet. They weigh in at approximately 5 lbs less than a comparable zinc carburetor. The new Ultra Double Pumper Carburetors have an enhanced fuel curve for optimum performance, with many more features such as aluminum construction; anodized billet aluminum metering blocks and base plate; 4 corner idle for precise idle control; mechanical secondaries for great performance; clear fuel level sight plugs for easy, no mess fuel level adjustments; Ford automatic transmission kickdown for use on popular Ford transmissions; four vacuum ports for all necessary vacuum accessories; and for the first time on a Double Pumper, factory pre-set electric choke for easy, fast cold start-ups. The clean, polished look coupled with Red, Blue, or Black metering blocks and throttle body will certainly set your ride apart whether you are at the show or track. Dont trust your performance to just anyone, Holley is the only Modular carburetor company that has been in business for over 100 years and has powered every NASCAR champion since the 60s.

Product Features:

• Gold Dichromate Finish For Corrosion Resistance w/Classic Look
• Optimized Street/Strip Calibration That Works Out Of The Box
• Man. Choke Cable Hand Controlled For Cold Start Control
• Mechanical Secondaries For Awesome Tire Turning Performance
• Dual Accelerator Pumps For Add Fuel Under Initial Acceleration
• Dual Feed Fuel Inlets For Constant High Volume Fuel Delivery
• Lightweight Vehicles w/Auto Trans w/High Stall/Low Gearing
• 100% Wet Flow Tested By Holley Technicians

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

• Vibratory Polished For Good Looks
• Optimized Street Calibration That Works Out Of The Box
• Factory Preset Electric Choke For Easy Startups
• Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
• No Unnecessary Trips Back To The Parts Store
• Limited Lifetime Warranty
• 100% Wet Flow Tested By Holley Technicians
• Arrives Ready To Run

Replace your old carburetor with original Holley performance 4160 carburetors. Budget-minded enthusiasts, like you, will be rewarded with maximum performance from your stock or mildly-modified engine. These Holley 4160 adjustable float carburetors are easier to tune than full race carburetors with temperamental secondary metering blocks and dual pumps. Plus, they’re available in your choice of universal or direct fit OE replacement versions with all emission provisions. Bolt-on installation and improved performance; no wonder when car guys think of carburetors, they think of Holley 4160 carburetors!

Product Features:

• Universal Holley 4-Barrel Carburetor

One of the most widely used Holley carbs of all times -the 0-80508S! Its dual feed fuel inlets assure you get all the fuel you need and its 750 CFM of airflow makes it the perfect performance upgrade carb. Its vacuum secondaries and electric choke make it super easy to use on a wide range of vehicles. Don’t trust your performance to just anyone, Holley is the only modular carburetor company that has been in business for over 100 years and has powered every NASCAR champion since the 60’s.

Product Features:

• Vibratory Polished For Good Looks

Classic Holley carbs have been a staple for rodders around the world for decades. They’re calibrated for use on stock to mildly modified vehicles and have that classic Holley look. Holley’s 0-8007 is calibrated and intended for small V8s or 6 cylinder engines as well as 2×4 street tunnel ram style set ups. Plus, it is Gold Dichromate coated for durability and classic Holley looks. Don’t trust your performance to just anyone, Holley is the only modular carburetor company that has been in business for over 100 years and has powered every NASCAR champion since the 60’s.

Product Features:

• Gold Dichromate Finish For Corrosion Resistance w/Classic Look
• Factory Preset Elec Choke For Easy Startups
• For All Weights/Gearing/Trans For Smooth Open Of Secondaries
• Single Feed Fuel Inlet For Easy Installation
• Power Valve Blow-Out Protection
• Does Not Work w/A.O.D. Transmissions
• Installation/Tuning DVD Incl.

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

• Vibratory Polished For Good Looks
• Optimized Street Calibration That Works Out Of The Box
• Manual Choke For Precise Cold Start Control
• Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
• No Unnecessary Trips Back To The Parts Store
• Limited Lifetime Warranty
• 100% Wet Flow Tested By Holley Technicians
• Arrives Ready To Run

The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a vacuum advance distributor and is calibrated for a hot street and strip engine setup for outstanding throttle response and drivability. A street HP base plate is used so there are plenty of vacuum ports for power brakes, PCV, etc.

Product Features:

• Gold Dichromate Finish For Corrosion Resistance w/Classic Look
• Performance Upgrade For Stock To Mildly Modified Vehicles
• Universal calibration for easy bolt-on performance
• Man. Choke Cable Hand Controlled For Cold Start Control
• Vacuum Secondaries For Use On Wide Variety Of Vehicles
• Dual feed fuel inlets for constant high volume fuel delivery
• Power Valve Blow Out Protection
• 100% Wet Flow Tested By Holley Technicians
• Arrives Ready To Run

The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a

Product Features:

• Vibratory Polished Alum Good Looks/Weight Savings/Lasting Shine
• Performance Upgrade For Stock To Mildly Modified Vehicles
• Universal Calibration For Easy Bolt-On Performance
• Man. Choke Cable Hand Controlled For Cold Start Control
• Vacuum Secondaries For Use On Wide Variety Of Vehicles
• Single Feed Fuel Inlet For Easy Installation

Product Features:

• The Edelbrock #12382 fuel bowl gasket is designed for Holley 2300, 4150, 4160, 4175 and 4500 Carburetors.
• Kit includes two black nitrile fuel bowl gaskets.

Product Features:

• The Edelbrock #12750 4160 Carburetor rebuild kit is for Holley, Demon and Quick Fuel Carburetors.
• The kit comes with the necessary components to rebuild a 4160 style Carburetor.

Product Features:

• The Edelbrock #12760 4150 Carburetor rebuild kit is for Holley, Demon and Quick Fuel Carburetors.
• The kit comes with the necessary components to rebuild a 4150 style Carburetor.

Product Features:

• The Edelbrock #12665 Single Stage 6.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
• During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.

The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a vacuum advance distributor and is calibrated for a hot street and strip engine setup for outstanding throttle response and drivability. A street HP base plate is used so there are plenty of vacuum ports for power brakes, PCV, etc.

Product Features:

• Gold Dichromate Finish For Corrosion Resistance w/Classic Look
• Performance Upgrade For Stock To Mildly Modified Vehicles
• Universal Calibration For Easy Bolt-On Performance
• Man. Choke Cable Hand Controlled For Cold Start Control
• Vacuum Secondaries For Use On Wide Variety Of Vehicles
• Single Feed Fuel Inlet For Easy Installation
• Power Valve Blow Out Protection
• 100% Wet Flow Tested By Holley Technicians
• Arrives Ready To Run
• Compensates For All Vehicle Weights Gearing/Transmissions

The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23

Product Features:

• Center Hung Floats
• 0.11 in. Needle Diameter
• Viton® Needle Material
• Sold Individually
• Non-Adjustable Type

The off-road truck avenger is designed specifically for off-road applications. The unique fuel metering block eliminates fuel spillover through the boosters at extreme angles allowing for 40 degree climbing, 30 degree side hill maneuvers and nose-down descents to avoid hesitations, stalling and flooding typically associated with carbs in an off road environment. The 470 CFM off-road truck avenger is the perfect carburetor for 4 cylinder, V-6, and inline 6 cylinder engines. Viton(R) is a registered trademark of DuPont Performance Elastomers.

Product Features:

• Gold Dichromate Finish For Extreme Off Road Environments
• Single Feed Fuel Inlet For Ease Of Installation
• Optimized Off-Road Calibration That Works Out-Of-The-Box
• Factory Preset Electric Choke For Easy Startups
• Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
• One Piece Off-Road Vent Tube Eliminates Fuel Spillover
• Metering Block For Flood Free Op. 40 deg. Climb/30 deg. Side Hill
• Limited Lifetime Warranty Defects In Material/Workmanship

Product Features:

• The Edelbrock #12602 Adjustable Inlet Needle and Seat assembly will fit Carburetors with center hung fuel bowls and can be used as replacements or performance upgrades.
• Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 4500 Series, Quick Fuel 4500, Professional Series and Q-Series, as well as various Demon Carburetors.

The Ultra Double Pumper Carburetors feature all aluminum construction and are equipped with metering blocks and a base plate made from 6061-T6 billet aluminum. Three different anodized color options (Red, Blue, or Black) allow for a personalized look while maintaining the ultra high strength and durability you get from billet. They weigh in at approximately 5 lbs less than a comparable zinc carburetor. The new Ultra Double Pumper Carburetors have an enhanced fuel curve for optimum performance, with many more features such as aluminum construction; anodized billet aluminum metering blocks and base plate; 4 corner idle for precise idle control; mechanical secondaries for great performance; clear fuel level sight plugs for easy, no mess fuel level adjustments; Ford automatic transmission kickdown for use on popular Ford transmissions; four vacuum ports for all necessary vacuum accessories; and for the first time on a Double Pumper, factory pre-set electric choke for easy, fast cold start-ups. The clean, polished look coupled with Red, Blue, or Black metering blocks and throttle body will certainly set your ride apart whether you are at the show or track. Dont trust your performance to just anyone, Holley is the only Modular carburetor company that has been in business for over 100 years and has powered every NASCAR champion since the 60s.

Product Features:

• Gold Dichromate Finish For Corrosion Resistance w/Classic Look
• Optimized Street/Strip Calibration That Works Out Of The Box
• Manual Choke For Precise Cold Start Control
• Mechanical Secondaries For Awesome Tire Turning Performance
• 4 Corner Idle Allows You To Precisely Control Your Idle System
• Dual Accelerator Pumps For Add. Fuel Under Initial Acceleration
• Dual Feed Fuel Inlets For Constant High Volume Fuel Delivery
• Lightweight Vehicles w/Auto Trans w/High Stall/Low Gearing

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

• Features A Tumble Polished Finish Can Also Be Hand Polished
• Optimized Street Calibration That Works Out Of The Box
• Factory Preset Electric Choke For Easy Startups
• Glass Fuel Level Sight Windows For Easy Safe Float Adjustments
• Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
• 4 Corner Idle Allows You To Precisely Control Your Idle System
• No Unnecessary Trips Back To The Parts Store
• Limited Lifetime Warranty
• 100% Wet Flow Tested By Holley Technicians

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

• Vibratory Polished For Good Looks
• Optimized Street Calibration That Works Out Of The Box
• Manual Choke For Precise Cold Start Control
• Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
• No Unnecessary Trips Back To The Parts Store
• Limited Lifetime Warranty
• 100% Wet Flow Tested By Holley Technicians

The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a vacuum advance distributor and is calibrated for a hot street and strip engine setup for outstanding throttle response and drivability. A street HP base plate is used so there are plenty of vacuum ports for power brakes, PCV, etc.

Product Features:

• Vibrant Polished Alum Good Looks/Weight Savings/Lasting Shine
• Performance Upgrade For Stock To Mildly Modified Vehicles
• Universal Calibration For Easy Bolt-On Performance
• Factory Preset Electric Choke For Easy Startups
• For All Weights/Gearing/Trans For Smooth Open Of Secondaries
• Dual Feed Fuel Inlets For Constant High Volume Fuel Delivery
• Power Valve Blow-Out Protection
• Clear Fuel Level Sight Glasses
• 100% Wet Flow Tested By Holley Technicians
• Arrives Ready To Run

The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a vacuum advance distributor and is calibrated for a hot street and strip engine setup for outstanding throttle response and drivability. A street HP base plate is used so there are plenty of vacuum ports for power brakes, PCV, etc.

Product Features:

• Vibrant Polished Alum Good Looks/Weight Savings/Lasting Shine
• Performance Upgrade For Stock To Mildly Modified Vehicles
• Universal Calibration For Easy Bolt-On Performance
• Factory Preset Electric Choke For Easy Startups
• For All Weights/Gearing/Trans For Smooth Open Of Secondaries
• Single Feed Fuel Inlet For Easy Installation
• Power Valve Blow-Out Protection
• 100% Wet Flow Tested By Holley Technicians

Product Features:

• The Edelbrock #12645 Single Stage 5.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
• During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.

The Gen 3 utilizes high capacity fuel bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, 12 hole billet booster inserts, fully tunable billet metering blocks, adjustable external linkage, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws Each calibration has been dyno and track tested to deliver proven performance!

Product Features:

• All Aluminum Construction Saves 3.8 lbs. Over Original Models
• 28% Weight Savings
• Calibrations For Todays Larger Race Engines and New Fuels
• Fully Machined From Venturi Throat To Throttle Bore
• Integrated Idle Bypass Valve Allows For Adjustment Of Idle
• 12 Hole Billet Booster Superior Atomization/Throttle Response
• Metering Blocks Feature Improved True Gasket Sealing
• Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
• Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
• Clear Sight Windows On Sides Of Bowl For Fuel Level Adjustments
• Drain Plug On Bowl Provides Easy Access To Empty Bowl
• Contoured Hex Head Squirter Screws For Streamlined Airflow

The Gen 3 utilizes high capacity fuel bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, 12 hole billet booster inserts, fully tunable billet metering blocks, adjustable external linkage, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws Each calibration has been dyno and track tested to deliver proven performance!

Product Features:

• All Aluminum Construction Saves 3.8 lbs. Over Original Models
• 28% Weight Savings
• Calibrations For Todays Larger Race Engines and New Fuels
• Fully Machined From Venturi Throat To Throttle Bore
• Integrated Idle Bypass Valve Allows For Adjustment Of Idle
• 12 Hole Billet Booster Superior Atomization/Throttle Response
• Metering Blocks Feature Improved True Gasket Sealing
• Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
• Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
• Clear Sight Windows On Sides Of Bowl For Fuel Level Adjustments
• Drain Plug On Bowl Provides Easy Access To Empty Bowl
• Contoured Hex Head Squirter Screws For Streamlined Airflow

The Gen 3 utilizes high capacity fuel bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, 12 hole billet booster inserts, fully tunable billet metering blocks, adjustable external linkage, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws Each calibration has been dyno and track tested to deliver proven performance!

Product Features:

• All Aluminum Construction Saves 3.8 lbs. Over Original Models
• 28% Weight Savings
• Calibrations For Todays Larger Race Engines and New Fuels
• Fully Machined From Venturi Throat To Throttle Bore
• Integrated Idle Bypass Valve Allows For Adjustment Of Idle
• 12 Hole Billet Booster Superior Atomization/Throttle Response
• Metering Blocks Feature Improved True Gasket Sealing
• Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
• Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
• Clear Sight Windows On Sides Of Bowl For Fuel Level Adjustments
• Drain Plug On Bowl Provides Easy Access To Empty Bowl
• Contoured Hex Head Squirter Screws For Streamlined Airflow

The Gen 3 utilizes high capacity fuel bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, 12 hole billet booster inserts, fully tunable billet metering blocks, adjustable external linkage, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws Each calibration has been dyno and track tested to deliver proven performance!

Product Features:

• All Aluminum Construction Saves 3.8 lbs. Over Original Models
• 28% Weight Savings
• Calibrations For Todays Larger Race Engines and New Fuels
• Fully Machined From Venturi Throat To Throttle Bore
• Integrated Idle Bypass Valve Allows For Adjustment Of Idle
• 12 Hole Billet Booster Superior Atomization/Throttle Response
• Metering Blocks Feature Improved True Gasket Sealing
• Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
• Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
• Clear Sight Windows On Sides Of Bowl For Fuel Level Adjustments
• Drain Plug On Bowl Provides Easy Access To Empty Bowl
• Contoured Hex Head Squirter Screws For Streamlined Airflow

Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.

Product Features:

• Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
• Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
• Thermally active pull cords for maintenance-free operation when the strap is properly installed and tensioned
• Resists oil, heat, ozone, weather and aging for improved belt life
• Meets or exceeds SAE J636C specifications

Product Features:

• The fiber-filled rubber adds flexibility along the entire length of the belt and provides greater lateral stability in the pulley.
• Ground to ensure precise dimensional control of the top width and sidewall for proper adjustment to the pulley.
• Thermoactivated pull cords for maintenance-free performance when properly installed and tensioned
• Resists oil, heat, ozone, weather and aging for improved belt life
• Meets or exceeds SAE J636C specifications