Heater Hose/Tube Assembly
Hover over the image to zoom in
Heater Hose/Tube Assembly
Share this:

Dorman - OE Solutions Heater Hose/Tube Assembly

Part No. 626-208 Warranty Details  
Quantity  Add to Cart

See if this part fits a specific vehicle.

Check Vehicle Fit

Durably engineered to resist corrosion and leakage, our HVAC Heater Hose limits the possibility of overheating and engine damage. Put your engine worries to rest by preserving coolant circulation.

Product Features:
  • Comes with clamps and fittings (where applicable)
  • Tough rubber and steel construction
  • Front and rear heating and cooling lines available (where applicable)
  • Rigorous quality control measures have been undertaken to ensure that this part conforms to product standards
Back To Top
Clamps Included:Yes
End 1 Attachment Type:Hose
End 1 Inside Diameter:0.59 in
End 1 Outside Diameter:0.93
End 2 Attachment Type:Hose
End 2 Inside Diameter:0.59 in
End 2 Outside Diameter:0.93
Heat Shield Included:No Heat Shield Required
Hose Type:Branched
Material:Steel /Rubber
Maximum Working Pressure:100 PSI
Overall Length:31.5
Protective Sleeve Attached:No Protective Sleeve Required
Thermostatically Controlled:No


by PowerReviews
Dorman - OE SolutionsHeater Hose/Tube Assembly

(based on 1 review)

Ratings Distribution

  • 5 Stars



  • 4 Stars



  • 3 Stars



  • 2 Stars



  • 1 Stars



Reviewed by 1 customer

Displaying review 1

Back to top

(1 of 1 customers found this review helpful)


Works Great, Replaces entire assembly.


from South Detroit, MI

About Me Auto Enthusiast, Mechanic, Truck Enthusiast


  • Durable
  • Easy To Install
  • Whole Assembly


    Best Uses

    • Everyday Driving
    • Replacement

    Comments about Dorman - OE Solutions Heater Hose/Tube Assembly:

    I am a mechanic and I have replaced this hose on at least a half dozen 96-2007 Taurus. Granted it may have not been the best design from the factory, but this part is a great replacement for the whole assmembly this is was easily a few hundred dollar replacement from the dealer. The first Taurus i replaced this on this part was not available aftermarket. If your hose in your car (the metal part) is starting to rust at all or the paint is flaking off. save your self an overheated engine that loves to pop head gaskets It only takes 1 time and you are doing a major repair vs. around $60 for this hose. Its not a horrible job to do just remove the air inlet and have someone with small hands take the clamps off, be careful not to snap the studs off that the nut holding this assembly to the firewall. Its also a great time to flush the cooling system once the factory hose starts to fail it sends rust through the entire cooling system. Coolant is cheap dont risk it. Good Luck, Thanks Advance for having the parts I need, the discount codes are nice too.

    Displaying review 1

    Back to top

    Do you have questions about this product?


    Ask a question, get answers from real customers and in-house experts. For further assistance, please review your support options on our Contact Us page.

    1 Question | 1 Answer
    Displaying question 1
    • Q:

      I need to replace the heater hose assy on a 1998 Ford Taurus 3.0. Any step by step directions?
      Asked on 8/27/2010 by tom from Bath,ME

      1 answer



        For step by step instructions i recommend that you go to your nearest Advance Auto Parts store and purchase a repair manual.

        Answered on 8/27/2010 by Kevin from AAP
    Displaying question 1

    Do you have a question about this product? 

    Check out the specials in our monthly flyer.
    Disclaimer We strive to keep all information accurate and up-to-date; however, product availability, pricing, promotions and store hours are subject to change without notice. Please contact Customer Care if you have any questions or corrections.