Molded Heater Hose
Hover over the image to zoom in
Share this:

CARQUEST by Dayco Molded Heater Hose

Part No. 87793 Warranty Details  
Quantity  Add to Cart

See if this part fits a specific vehicle.

Check Vehicle Fit

This CARQUEST by Dayco® Small I.D. Molded Heater Hose is designed to replace OEM coolant hose and provide long, reliable service. This hose has a "quick connect" end assembled onto the hose for fast, convenient installation. With this CARQUEST by Dayco® product you avoid the hassle of buying a separate connector and clamp and having to install it before the hose can be used.

Product Features:
  • Made with a tough EPDM rubber compound this hose is made to resist the detrimental effects of heat, ozone and impacts from road debris
  • This hose meets SAE J20R4, Class D1 and SAE J1684 Type EC specifications
  • Highly resistant to electro-chemical degradation and premature stress cracking of the tube
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Back To Top
End 1 Inside Diameter:3/4 in
End 2 Inside Diameter:3/4 in
Heat Shield Included:N
Hose Type:Single I.D. Hose
Overall Length:21 in
Protective Sleeve Included:N
SAE:SAE J20R3 Class D-1, SAE J1684 Type EC
Trunk Height:21

Do you have questions about this product?


Ask a question, get answers from real customers and in-house experts. For further assistance, please review your support options on our Contact Us page.

2 Questions | 3 Answers
Displaying questions 1-2
  • Q:

    Does this hose have the flow restrictor built in it and where is it located in the hose?
    Asked on 3/10/2013 by Randy from Chester, SC

    1 answer



      No, this Drive-Rite Molded Heater Hose, Part No. 303793 does not have the flow restrictor built in it.
      For compatibility of this part with your vehicle, please provide your vehicle make, model and engine specification.
      For any further assistance please feel free to call us at: 1-877-238-2623 or visit the nearest Advance Auto Parts store and one of our Parts Pros will gladly assist you with any questions or concerns you may have.

      Answered on 3/11/2013 by Aaron from AAP
  • Q:

    Where exactly does this hose go in the Ford 5.4 L engine? Is it the hose that runs underneath the intake manifold from the front of the engine to the rear towards the heater?
    Asked on 5/13/2012 by Suite Lou from Chicago, Il.

    2 answers



      The heater hose normally runs along the passenger side of the engine, back towards the firewall. To access, loosen the hose clamps on both heater hoses where they connect to the heater core inlet and outlet at the firewall using the screwdriver. Slide the clamps away from the hose ends. Follow the hoses to the heater control valve and intake and loosen the hose clamps at those ends as well with the screwdriver. Slide those clamps away from the hose ends. Pull the hose ends off the heater core inlet and outlet by hand. If the hoses do not slide free easily, insert the tip of the mechanic's pick between the hose end and the heater core inlet and/or outlet and slide the tip all the way around the hose end to free them from the heater core. For any further assistance please feel free to call 1-877-238-2623 and one of our representatives will gladly assist you with any questions or concerns you may have.

      Answered on 5/15/2012 by John the Car-Doc from AAP
    • A:

      This hose goes from the intake manifold to the heater inlet at the firewall.

      Answered on 4/6/2013 by jpride from kingsport, tn
Displaying questions 1-2

Do you have a question about this product? 

Check out the specials in our monthly flyer.
Disclaimer We strive to keep all information accurate and up-to-date; however, product availability, pricing, promotions and store hours are subject to change without notice. Please contact Customer Care if you have any questions or corrections.