Chevrolet K30 Belts and Hoses
Top Chevrolet K30 Belts and Hoses Categories
We carry over 196 Belts and Hoses in inventory for the Chevrolet K30. If you’re looking for aftermarket Belts and Hoses for your Chevrolet K30, check out all these categories:
Essential Chevrolet K30 Belts and Hoses
Gates – Vulco-Flex½ II Flexible Coolant Hose (Part No.25307)
from
$39.99
Product Features:
See More
- Improved sealing surface for greater leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimum inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature Range: up to +257 Deg. F (+125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dorman – Help – Carburetor Pre-Heater Hose – 1-1/2 In. X 18 In. – Aluminum (Part No.96020)
from
$6.99
This HVAC control duct hose is designed to match the fit and function of the original hose on specified vehicles, and is engineered for durability and reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this HVAC control duct hose is designed to match the fit and function of the original hose on specified vehicles
- Restores functionality – reliable replacement for an original hose that has failed due to heat or vibration
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Gates – Molded Heater Hose: EPDM, Direct Fit, 1.5" Inside Diameter (Part No.20686)
from
$40.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube; synthetic fiber knit reinforcement; heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 14.50" Long, 1.75" Diameter (Part No.C70623)
from
$24.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dorman – Help – Fuel Hose Clamp Kit (Part No.90099)
from
$9.99
This fuel hose clamp is designed to match the fit and function of the original clamp on specified vehicles, and is engineered for durability and reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this fuel hose clamp is designed to match the fit and function of the original clamp on specified vehicles
- Restores functionality – this clamp is made to fit and fully restore part functionality after the original clamp fails
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 4.50" Long, .63" Diameter (Part No.A70785)
from
$11.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 24" Long, 1.50" Diameter (Part No.E70935)
from
$25.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dorman – Diesel Fuel Injection Return Hose and Clamps (Part No.904-101)
from
$44.99
This fuel hose is designed to match the fit and function of the original hose on specified vehicles, and is engineered for durability and reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this fuel hose is designed to match the fit and function of the original hose on specified vehicles
- Restores functionality – reliable replacement for an original hose that has failed due to heat and vibration
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)
from
$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)
from
$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
Carquest Premium – Fuel Injector Return Hose Kit (Part No.AL001)
from
$39.99
This complete kit includes necessary components to replace the fuel injector return lines and copper gaskets on the fuel injectors.
Product Features:
See More
Product Features:
- Includes fuel return line
- Includes 8 fuel injector copper combustion seals
- Includes 2 caps
- Includes 2 clamps
- Includes 2 plenum gaskets
- Premium OE quality materials
Yukon Gear – Seal Puller Tool (Part No.56063)
ACDelco – Heater Hose Connecto (Part No.R3036209226ACD)
from
$18.86
Heater Hose Connecto
Dayco – Bottom Cog V-Belt; 46 Inch Long, Exact Fit Premium Quality (Part No.15460)
from
$21.29
Dayco has combined raw-edge construction and a smooth top to ensure high performance on vehicles and drives that utilize V-belts. The Dayco high performance V-belt delivers more flexibility and increases airflow around the belt so it runs cooler and lasts longer. Three plies of neoprene impregnated fabric resist heat, oil and grease while a specially-formulated treatment of the polyester cord provides the strength, stability and reliability that are required for one of the most innovative, top-performing V-belts.
Product Features:
See More
Product Features:
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Prevents electromechanical interference issues on modern vehicles
- Resists heat, oil and grease
Gates – Automotive XL« High Capacity V-Belt (Part No.9300)
from
$22.99
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
- Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
- Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
- Resists oil, heat, ozone, weather and aging for improved belt life
- Meets or exceeds SAE J636C specifications
Driveworks – Poly Rib Belt Serpentine Belt; 61.25 Long, 6 Rib Count (Part No.54515)
from
$4.99
Dayco engineered to conform to high mileage, worn or misaligned drives without a sacrifice in quiet, long-lasting performance. Constructed with Aramid reinforced EPDM compounds, it delivers more than OE required quality… it delivers the solution to troublesome drive problems. Dayco Poly-Rib Belts meet or exceed SAE J1459 and SAE J2432 specifications.
Product Features:
See More
Product Features:
- Aramid noise resistant fibers embedded in the rubber make this belt run quieter in worn or misaligned pulleys
- No-Noise Advanced Design EPDM rubber compound for quiet extended life
Edelbrock – Fuel Bowl Inverted Flare Fuel Inlet Fitting #12415 (Part No.12415)
from
$20.99
Edelbrock part #12415 Fuel Bowl Inverted Flare Fitting is a 3/8″ inverted flare fuel inlet fitting. The fitting is designed for use with Holley 2300, 4150, 4150HP and 4160 (center hung floats only), 4500, 4500HP and Rochester Quadrajet applications up to
Product Features:
See More
Product Features:
- Brass Material
- 3/8 in. Single Barb
- 7/8-20 in. Male End
- 5/8-18 in. Female Flare
- With 3/8 in. Tube
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 3.50" Long, .75" Diameter (Part No.A70647)
from
$11.79
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Driveworks – Poly Rib Belt Serpentine Belt; 56 Long, 6 Rib Count (Part No.560K6)
from
$29.99
The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.
Product Features:
See More
Product Features:
- Constructed with heat and ozone resistant EPDM rubber
- Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
- Made with treated polyester cord to reduce belt stretch
Dayco – Poly Rib Belt Serpentine Belt; 56 Long, 6 Rib Count (Part No.5060560)
from
$32.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
- Made in the USA
Dayco – Poly Rib Belt Serpentine Belt; 43.31 Long, 5 Rib Count (Part No.5050433)
from
$31.49
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
Driveworks – Poly Rib Belt Serpentine Belt; 43.31 Long, 5 Rib Count (Part No.433K5)
from
$15.79
The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.
Product Features:
See More
Product Features:
- Constructed with heat and ozone resistant EPDM rubber
- Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
- Made with treated polyester cord to reduce belt stretch
Gates – V-Ribbed (Heavy Duty) Serpentine Belt: 56.658" Long, 6 Rib Count, Exact Fit (Part No.K060560HD)
from
$37.99
Gates FleetRunner Micro-V Belts are designed for the toughest applications. FleetRunner construction provides superior flexibility, stability, load capacity, and unsurpassed belt life. Patented materials deliver peak performance at extreme prolonged operating temperatures, making this belt the ultimate problem solver. An advanced blend of EPDM rubber technology withstands the modern threats of deterioration from increased exposure to ozone and water-based coolants. FleetRunner does this all while providing the lowest cost per mile for fleets, including 3/4 and 1 ton pickups.
Product Features:
See More
Product Features:
- Patented material provides peak performance at prolonged extreme operating temperatures
- Heavy-duty construction resists cracking and wear, even at extreme temperatures
- Special compound provides unmatched flexibility, stability, load carrying capacity and belt life
- Problem solver designed for the toughest applications
- Consistently outperforms other heavy-duty serpentine belts on the market
- Engineered to save your fleet money and reduce downtime
- Tensioner Replacement is Recommended (if equipped)
Gates – Micro-V« Serpentine Drive Belt (Part No.K050435)
from
$30.49
Import or domestic, car or truck, every vehicle can depend on the superior quality of Gates precision fit Micro-V belts. With advanced technology that matches the OE size, construction and materials, Gates Micro-V ensures optimal vehicle performance.
Product Features:
See More
Product Features:
- Special belt construction eliminates belt noise, reduces tension loss and solves problem drive applications
- EPDM rubber constructions resist cracking on the rib surface
- Meets or exceeds all specifications from the Original Equipment Manufacturer
- Tensioner Replacement is Recommended (if equipped)
- Unique form grinding of each individual belt assures precise dimensional control.
- Meets or exceeds SAE J1459, SAE J2432, and SAE J1596 specifications.
Chevrolet K30 Belts and Hoses Categories
Helping You Find the Right Belts and Hoses for Your Chevrolet K30
You love your K30. So we’ve made it easier than ever to help you find Chevrolet K30 Belts and Hoses in our online catalog. Our inventory holds 196 aftermarket and OEM Belts and Hoses for your Chevrolet K30, ranging from $1.49 to $86.89.
We offer parts from 12 brands trusted to make quality Belts and Hoses for your Chevrolet K30. Before you buy, take some time to read through customer reviews. We currently have 3,979 reviews of Chevrolet K30 Belts and Hoses from previous customers. Some of the top rated parts include Bottom Cog V-Belt; 34.5 Inch Long, Exact Fit Premium Quality with 4.8 stars and Curved Radiator Hoses: EPDM Rubber, Standard Duty, 18" Long, 1.50" Diameter with 4.7 stars.
Find your K30 Belts and Hoses here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Chevrolet K30 part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Belts and Hoses Brands for Your Chevrolet K30
Our inventory holds Belts and Hoses for your Chevrolet K30 from 12 trusted brands. You’ll find OEM and aftermarket parts from brands like Dayco, Driveworks, and Dorman, all of which can keep that Chevrolet happy.
We have Dorman parts available for your Chevrolet K30 in categories like Fuel Hoses and Duct Hoses. Some of the top-rated Dorman parts in these categories are:
Top-Rated Dayco Belts and Hoses
Leading Dayco Belts and Hoses
We carry Dayco brand parts for your Chevrolet K30 across several catalog categories, including Radiator Hoses and Serpentine and V Belts. Some of our most reviewed Dayco parts include:
from
$24.99
(184)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 14.50" Long, 1.75" Diameter
Coolant Hoses
from
$18.79
(17)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 24" Long, 1.25" Diameter
Upper Radiator Hoses
FAQs for Chevrolet K30 Belts and Hoses
What are the most purchased Belts and Hoses for the Chevrolet K30?
Out of 196 Belts and Hoses for the Chevrolet K30, the most popular in our inventory are:
What are the top-rated Chevrolet K30 Belts and Hoses?
Top-rated Belts and Hoses for your Chevrolet K30 based on customer reviews/ratings are:
from
$15.79
(12)
Bottom Cog V-Belt; 34.5 Inch Long, Exact Fit Premium Quality
“I use this as the wheel drive belt for my older riding mower. I have used this belt before as it works much better than the substitute belt manufactur”
