-
Your Store:
-
Hover over the image to zoom in
Driveworks Wheel Hub Assembly
See if this part fits a specific vehicle.
Fully integrated mounting wheel flange
Back To Top
| Bearing Type: | Ball Bearing |
| Material: | 65Mn Steel |
| Sealed: | Yes |
REVIEW SNAPSHOT®
by PowerReviewsDriveworksWheel Hub Assembly
(based on 41 reviews)
Ratings Distribution
69%
of respondents would recommend this to a friend.
Pros
- Easy to use (24)
- Durable (6)
- Easy to install (3)
Cons
- Flimsy (6)
- Poor quality (4)
Best Uses
- Large cars (7)
- Small cars (6)
- Trucks (4)
- Car & Truck:
- Casual driver (11), Mechanic (4), Auto enthusiast (3)
- Reviewer Profile:
- Casual driver (11), Mechanic (4)
- Was this a gift?:
- No (22)
Most Liked Positive Review
Exact Fit
Exact fit, easy to install....
Exact fit, easy to install....
VS
Most Liked Negative Review
Not so hot
I purchased this to replace the left front hub assembly in my 2004 Pontiac Bonneville. I found the part easy to install; however, the bearing went bad only a month after install. I ...Read complete review
I purchased this to replace the left front hub assembly in my 2004 Pontiac Bonneville. I found the part easy to install; however, the bearing went bad only a month after install. I exchanged it for a National Hub Assembly. At the same time I did the exchange I went ahead and purchased a different brand for the right front. (SKF) I noticed the SKF brand was significantly better quality and the rear bearing seal was totally redesigned (the SKF came with a document explaining the redesign), some investigation into SKF revealed SKF is an engineering company not just a manufacturer. 2 Months later the National Hub Assembly has play in it while the SKF is like new. I think Advance should start selling the SKF brand.
REVIEWS
Reviewed by 41 customers
Sort by
Displaying reviews 1-10
Previous | Next »
Pros
- Easy To Use
- Perfect Fit
Cons
- Not durable
Best Uses
- Small Cars
Comments about Driveworks Wheel Hub Assembly:
Lasted 13 months
- Was this a gift?:
- No
Pros
Cons
Best Uses
Comments about Driveworks Wheel Hub Assembly:
Great price, ordered on line and picke up an hour later. I was on vacation and need to get the van fixed without spending alot of monaey.
- Was this a gift?:
- No
Pros
Cons
- Flimsy
Best Uses
Comments about Driveworks Wheel Hub Assembly:
Well first one I received the lug nut stubs were bent so I returned it. Second one I installed the ABS light stayed on and I tested the wheel hub. The wheel speed sensor didn't work. So I ended up removing it and buying a more expensive one Moog brand.
- Was this a gift?:
- No
Pros
- Durable
- Easy To Use
- High-Performance
- Lightweight
- Perfect Part
- Versatile
Cons
Best Uses
Comments about Driveworks Wheel Hub Assembly:
The part was correct as ordered. Perfect fitment and eliminated the noise. BUICK is rolling as it should now....
- Was this a gift?:
- No
Pros
- Easy To Use
Cons
Best Uses
Comments about Driveworks Wheel Hub Assembly:
So far its ok item
- Was this a gift?:
- No
Pros
- Durable
- Easy To Use
Cons
Best Uses
Comments about Driveworks Wheel Hub Assembly:
Perfect fit and eay to install
- Was this a gift?:
- No
Pros
- Easy To Use
Cons
- None
Best Uses
- Large Cars
Comments about Driveworks Wheel Hub Assembly:
I put this part on two weeks ago, no problems so far.
- Was this a gift?:
- No
Pros
Cons
Best Uses
Comments about Driveworks Wheel Hub Assembly:
Thanks! I will shop here again
- Was this a gift?:
- No
Pros
Cons
Best Uses
Comments about Driveworks Wheel Hub Assembly:
Will use again
- Was this a gift?:
- No
Pros
Cons
Best Uses
Comments about Driveworks Wheel Hub Assembly:
very good service and deliveryl..would use them again.
- Was this a gift?:
- No
Do you have questions about this product?(earn points for answers!)
Ask a question, get answers from real customers and in-house experts. Or contact Customer Care by email or call 1-877-238-2623.
20 Questions | 23 Answers
Displaying questions 1-10Previous | Next »
Q:
what torque foot lbs on 2004 impala ls 3.8 for front hub bearing assembly nut (axle)Asked on 2/2/2013 by Dave from Blountstown Fl1 answer
CUSTOMER CARE
A:
With reference to your inquiry on the Driveworks Wheel Hub Assembly - part# NT513179, torque the front hub/bearing assembly to 96 ft-lbs on your Chevy Impala. However, I would suggest you to refer your vehicle owner's manual for the exact torque specifications in order to avoid intermittence. For any further assistance, please visit your nearest Advance Auto store or call us directly at 1-877-ADVANCE (238-2623) and one of our representatives there would be more than happy to assist you.Answered on 2/4/2013 by Vincent from AAP
Q:
How can I tell if the berring in the hub is bad or not?Asked on 7/4/2012 by J from waco TX1 answer
CUSTOMER CARE
A:
When a Wheel Bearing or Hub Assembly is bad, it will usually make a noise. The noise can vary when you turn, and also with speed. This grinding noise indicates that your wheel bearings are bad, and you should replace them. Common noises are squeaks, chirps, squeals, moans, grinding, growling, whining, etc. This noise usually does not vary with braking. If you are experiencing noise while breaking or that varies with applied brake pressure, then you most likely need to replace your brakes. Another way, To check a wheel bearing, grasp the tire at the 12 and 6 o'clock positions and attempt to rock the tire (while the wheel is lifted off the ground). If you feel any play, the bearings are loose and need to be replaced. Also, rotate the tire by hand. Any roughness or noise from the bearings would also tell you the bearings are worn or damaged and need to be replaced. Also, If one wheel bearing is faulty, pay close attention to all of the other hubs on the vehicle, too, especially if the vehicle has a lot of miles on it. Chances are some of the other bearings may also need replacement.
For any further assistance, please feel free to call us at 1-877-238-2623 or visit your nearest Advance Auto Parts store and our representatives would be more than happy to assist you.Answered on 7/4/2012 by Aaron from AAP
Q:
Does this wheel hub assembly have the sensors already in it?Asked on 6/11/2012 by Anonymous1 answer
CUSTOMER CARE
A:
The specification of this part Driveworks Wheel Hub Assembly, Part No. NT513179: Flange Diameter: 5.73 In., Bolt Circle Diameter: 4.53 In., Wheel Pilot Diameter: 2.76 In., Brake Pilot Diameter: 2.78 In., Flange Offset: 2.74 In., Hub Pilot Diameter: 3.60 In., Hub Bolt Circle Diameter: 4.57 In., Bolt Size: M12X1.5, Bolt Quantity: 5, Bolt Hole MET: M12X1.75, Bolt Hole qty: 3, Flange Shape: TRIANGULAR, ABS Sensor: Has ABS with Integral Sensor, Number of Splines: 33.
For compatibility of this part with your vehicle, please provide your vehicle make, model and engine specification.
For any further assistance, please feel free to call us at 1-877-238-2623 or visit your nearest Advance Auto Parts store and our representatives would be more than happy to assist you.Answered on 6/14/2012 by Aaron from AAP
Q:
Can you use a wheel hub assembly with ABS on a car without ABS? (for an 03 Impala 3.4L without ABS)Asked on 6/6/2012 by Erin from Berlin, CT2 answers
A:
yes you canAnswered on 6/7/2012 by fer from nebraskaCUSTOMER CARE
A:
The wheel hub assembly with ABS does not fit for the vehicles without ABS. This Driveworks Wheel Hub Assembly (Part# NT513179) fits 2003 Chevrolet Impala with Integral ABS. For further assistance please call us at 1-877-ADVANCE (238-2623) and we would be more than happy to assist you.Answered on 6/6/2012 by Dennis from AAP
Q:
is this a hard part to change?Asked on 2/25/2012 by jay the rookie mechanic from cut off, louisiana1 answer
CUSTOMER CARE
A:
Normally this wheel hub assembly is built into the wheel hub and designed to be replaced as a single unit. This reduces the number of special tools you will need, because there is no need to pull or press the bearing. Expect to spend about half an hour replacing the wheel hub and bearing assembly which is moderately easy to replace.Answered on 2/25/2012 by John the Car-Doc from AAP
Q:
Does this include the three bolts required for installation? GM requires new bolts.Asked on 10/4/2011 by Anonymous1 answer
CUSTOMER CARE
A:
This part is sold individually.Answered on 10/5/2011 by Aaron from AAP
Q:
can this wheel hub assembly be used on the left or right front wheel?Asked on 6/24/2011 by thejonesfam from waynesboro, virginia1 answer
CUSTOMER CARE
A:
Yes, it can be used on both left and right front wheel.Answered on 6/28/2011 by Steve from AAP
Q:
I just took off my hub assembly off / This assembly look different becuase of the plastic on the end / how am I going to get the axel through the bearing and plug it in?Asked on 3/22/2011 by Michael` from San Antonio, TX1 answer
CUSTOMER CARE
A:
In order for us to further assist you, would you please provide us with the year, make, model, and engine size of your application?Answered on 3/23/2011 by Parts Guru Geo from AAP
Q:
what is the torque specs for this wheel bearing for a 2005 impalaAsked on 10/29/2010 by Anonymous1 answer
CUSTOMER CARE
A:
I believe it is 160 ft. lbs. but I would call your local dealership to confirm.Answered on 11/1/2010 by Mike the Auto Parts Master from AAP
Q:
what size socket is needed to pull bearing off?Asked on 7/10/2010 by Anonymous2 answers
VERIFIED BUYER
A:
36MM
see here for instructions - http://www.paulstravelpictures.com/GM-Wheel-Bearing-Hub-Assembly-Replacement/index.htmlAnswered on 9/29/2010 by Mike from Syracuse NYCUSTOMER CARE
A:
For step by step instructions and correct tool usage i recommend that you go to your local Advance Auto Parts store and purhcase a repair manual.Answered on 8/31/2010 by Kevin from AAP
Displaying questions 1-10Previous | Next »
Disclaimer
We strive to keep all information accurate and up-to-date; however, product availability, pricing, promotions and store hours are subject to change without notice. Please contact
Customer Care
if you have any questions or corrections.
