-
Your Store:
-
Hover over the image to zoom in
BWD Fuel Injector Seal Kit
See if this part fits a specific vehicle.
BWD fuel injector seal kits are manufactured to meet or exceed OE performance.
Back To Top
REVIEW SNAPSHOT®
by PowerReviewsBWDFuel Injector Seal Kit
(based on 4 reviews)
Ratings Distribution
100%
of respondents would recommend this to a friend.
Pros
Cons
Best Uses
- Everyday driving (3)
REVIEWS
Reviewed by 4 customers
Sort by
Displaying reviews 1-4
Pros
- Easy To Install
Cons
Best Uses
- Everyday Driving
Comments about BWD Fuel Injector Seal Kit:
simple install
Pros
Cons
- Difficult To Install
Best Uses
- Replacement
Comments about BWD Fuel Injector Seal Kit:
A little difficult to fit the fuel dispersion nipple. Use the forums for to get better installation instructions. Poor packaging from distribution source. Lost one in shipping and had to buy a local replacement.
Pros
- Easy To Install
Cons
Best Uses
- Everyday Driving
Comments about BWD Fuel Injector Seal Kit:
Easy to install, remember to coat seals in motor oil for easy install and sealing.
Pros
- Durable
Cons
- Difficult To Install
Best Uses
- Everyday Driving
Comments about BWD Fuel Injector Seal Kit:
Seals are good and correct fitment but blue cap to disperse fuel inside cylinder is extremely hard plastic and not very easy to attach to lower end of injector- broke 1 in process had to go buy 2nd kit to finish the job. probably should have soaked the blue cap in hot water to soften it to make it easier to install as you would plastic fuel line repairs.
Displaying reviews 1-4
Do you have questions about this product?(earn points for answers!)
Ask a question, get answers from real customers and in-house experts. Or contact Customer Care by email or call 1-877-238-2623.
6 Questions | 8 Answers
Displaying questions 1-6
Q:
On the fuel injector rebuild kit what are the four pieces i no 3 are o-rings is the fourth piece the hat.Asked on 1/19/2013 by kenny from reading pa1 answer
CUSTOMER CARE
A:
This BWD Fuel Injector Seal Kit part# 274081 contains 2 O-Rings, 1 Pintle Cap and 1 Spacer. For further assistance, please feel free to call us at 1-877-238-2623 or visit your nearest Advance Auto Parts store and one of our representatives would be more than happy to assist you.Answered on 1/20/2013 by Morgan from AAP
Q:
I have one of these kit and the plastic ring is sloppy going on, wont this burn out the O ring prematurely thru the gap between the injector and the plastic ring with the heat from exploding gas on the combustion stroke? The original ring fit snug as I think this one shouldAsked on 11/4/2011 by lionheart from hagerstown2 answers
CUSTOMER CARE
A:
If this injector seal kit is an exact fit, it should not burn out the O ring and the plastic ring.Answered on 11/7/2011 by Vincent from AAPA:
job done! This kit will work but like I said its not the right kit for these injectors, these injectors take a type #3 pintle cap this is for type 1 & 2 and dont use the yellow spacer. if you use this kit you have to remove the end of the pintle cap to get the right flow of gas. if not it will have uneven idle. you can cut it or you can grind or sand it off but dont damage the end of the injector or its ruined. and dont put the cap on too tight, just let it touch the O-ring or you will chip the O-ring putting them back in the manifold. Would be nice to be able to Buy the cone screen at Advance also but mine did not have it. VERY IMPORTANT after you are done installing the injectors you need to let the PCM recalibrate the gas flow, let it run for 15 mins. shut it off and do it again, and DONT REV UP THE MOTOR, dont even put your foot on thr gas the whole time during the calibation the computer is reading the motor sensors reving it up will interfear with this giving it false readingsAnswered on 11/7/2011 by lionheart763 from Hagerstown
Q:
Is this a rebuild kit for the internal seals on the injector mine is leaking in the center where they go togetherAsked on 12/7/2010 by meyermw from NC2 answers
CUSTOMER CARE
A:
YesAnswered on 12/24/2010 by Parts Guru Geo from AAPA:
Despite what "Parts Guru Geo" seems to think, this *is not* a kit to rebuild the internal injector seals. This kit seals the end of the injector to the intake manifold. I have never seen anyone offer any kind of internal seal kit for multi-port fuel injectors and I don't think there really are any internal seals. Most of the cut away drawings I've ever seen of injectors indicate a metal-to-metal interface where the center needle rests against the injector body.
If your are leaking from the center needle, I would suspect a proper and thorough cleaning would be needed.Answered on 3/9/2011 by Bryan from Upstate, SC
Q:
If injector is leaking instead of buying the injector y can't or can you just get the injector seal kitAsked on 11/8/2010 by Anonymous1 answer
CUSTOMER CARE
A:
You may be able to get away with just getting this kit.Answered on 11/8/2010 by Mike the Auto Parts Master from AAP
Q:
how many injectors seals come with the setAsked on 5/3/2010 by Anonymous1 answer
CUSTOMER CARE
A:
Contents 2 O-Rings, 1 Pintle Cap, 1 SpacerAnswered on 5/4/2010 by Rose from AAP
Q:
is this a rebuild kitAsked on 4/21/2010 by Jay from San Angelo Tx1 answer
CUSTOMER CARE
A:
This is just a kit that contains fuel injector seals.Answered on 4/22/2010 by Kevin from AAP
Displaying questions 1-6
Disclaimer
We strive to keep all information accurate and up-to-date; however, product availability, pricing, promotions and store hours are subject to change without notice. Please contact
Customer Care
if you have any questions or corrections.
