| Find out if this part fits your car. | Select a Vehicle |
REVIEWS
Reviewed by 1 customer
Displaying review 1
Pros
Cons
Best Uses
Comments about BWD Headlight Switch:
Comes with Life Time warranty, very
easy to install.
Displaying review 1
Do you have questions about this product?(earn points for answers!)
Ask a question, get answers from real customers and in-house experts. Or contact Customer Care by email or call 1-877-238-2623.
Q:
how do you install the knob into the switch there dfoesnt seem to be a wayinto it, looks to be a closed unit my knob pulled out of mine and i cant figure out how to fix it.1 answer
CUSTOMER CARE
A:
Disconnect and isolate the battery negative cable. The vehicle is so equipped, move the tilt steering column to the fully raised position. Remove the three screws that secure the lower edge of the steering column opening cover to the lower instrument panel reinforcement. Using a trim stick or another suitable wide flat-bladed tool, gently pry the upper edge of the steering column opening cover away from the instrument panel on each side of the steering column to release the two snap clip retainers that secure the cover to the instrument panel. Remove the steering column opening cover from the instrument panel. Remove the two screws that secure the knee blocker to the instrument panel. Pull the knee blocker away from the instrument panel far enough to disengage the two lower mounting tabs from the slots in the lower instrument panel reinforcement. Remove the knee blocker from the instrument panel. Pull the headlamp switch control knob out to the On position stop. Reach up through the outboard side of the instrument panel steering column opening and depress the headlamp switch knob and shaft release button on the inboard side of the switch. While holding the release button depressed, pull the knob and shaft out of the headlamp switch. Remove the spanner nut that secures the headlamp switch to the instrument panel. Pull the headlamp switch into the steering column opening area of the instrument panel far enough to access the wire harness connectors. Unplug the two wire harness connectors from the headlamp switch. Remove the headlamp switch from the instrument panel. Reverse the removal procedures to install. Tighten the spanner nut to 2.7 N·m (24 in. lbs.). For any further assistance please feel free to call 1-877-238-2623 and one of our representatives will gladly assist you with any questions or concerns you may have.Q:
does this switch include the knob ?1 answer
CUSTOMER CARE
A:
No, this BWD Headlight Switch with part# S2036Z does not include the knob.Q:
On my 87 Dodge truck D 150 have to replace head light switch your part #S2036Z shows the switch but my old switch has a stem with a knob that pulls out to turn lights on. Is this the right replacement part?1 answer
CUSTOMER CARE
A:
Yes, this BED headlight switch fits your 1987 Dodge D150.Q:
my switch only has 6 six prongs. will this still work1 answer
CUSTOMER CARE
A:
In order for us to further assist you, would you please provide us with the year, make, model, and engine size of your application?Q:
how do you remove and check this switch1 answer
CUSTOMER CARE
A:
For help with your project, I recommend purchasing a Haynes repair manual specifically for your vehicle. This should be able to assist you further into detail on how to repair or replace specific parts.Q:
Do you'll sell the connector to, and if the connector have a burnt spot on it, do it need to be replaced?1 answer
CUSTOMER CARE
A:
Yes it should be replaced and yes we care the part but to further assist you on this question could you please provide your vehicles year, make model, and engine size.Q:
Is this switch for the headlights and dash board1 answer
CUSTOMER CARE
A:
If you could provide us with the year, make, model and engine size of your vehicle we would be more than happy to see if we carry the right part you are looking for.Q:
is this 9or 10 prungs1 answer
CUSTOMER CARE
A:
The Bwd Headlight switch is a 9 prong switch.
Enter your zip code:
