5W-20 Full Synthetic Motor Oil (5 Quarts)
Hover over the image to zoom in
Share this:
Please Note: This item is not eligible for further promotional discounts, coupons or special offers.

Valvoline SynPower 5W-20 Full Synthetic Motor Oil (5 Quarts)

Part No. 787023 Warranty Details  
SynPower Full Synthetic Motor Oil delivers superior engine protection by fighting the three major causes of engine stress: heat, deposits and wear. That's because SynPower is the only leading full synthetic formulated with more durable anti-wear additives

Product Features:
  • Excellent engine cleanliness through superior sludge and varnish protection
  • Outstanding high-temperature protection under severe driving conditions
  • Superior cold-temperature protection through faster oil flow at start-up
  • Is fully compatible with all conventional and leading synthetic motor oils
Back To Top
API Service Category:SN/SM
ATV:No
Container Size:5.1 qt
Conventional:No
Detergency:Detergent
Diesel Approved:No
Race Only:No
Synthetic:No
Synthetic Blend:No
Viscosity Index:160

Do you have questions about this product?

 

Ask a question, get answers from real customers and in-house experts. For further assistance, please review your support options on our Contact Us page.

1 Question | 1 Answer
Displaying question 1
  • Q:

    What is the exact procedure to blow up an engine (or 2 engines) using Full Synthetic 5W-20 oil ?
    Asked on 3/31/2012 by Anonymous

    1 answer

    • CUSTOMER CARE

      A:

      Jack your car up or use drive-on ramps. Pop the hood. Remove the oil fill cap and dipstick, then use the oil filter wrench to loosen the oil filter housing 4-5 complete turns to allow the air to get in so the oil can drain out. Temporarily put the oil pan under the filter to capture any spillage. Place the oil drain pan directly under the drain plug on the engine. Drain the oil. Using a socket wrench or a combination wrench of the right size, loosen the oil drain plug on the engine and remove it completely. Let the oil drain completely from the engine. Save the used oil. Collect it in a clean container and take it to a recycling center. To find a recycling drop off point, check with your local auto parts retailer. Tighten the drain plug. Replace the drain plug on the engine oil pan then tighten it. Remove the oil filter. Place the drain pan directly under the oil filter. The filter should be removable by hand. If not, use your filter wrench and rotate the filter counter-clockwise to remove it. Rub the gasket. Before attaching the new filter, rub motor oil on the rubber gasket on the base. If you don't do this, it will be hard to get the filter off the engine the next time. Make sure the gasket from the old filter came off and is not still stuck on the housing. Screw on the new filter. Screw the new filter onto the filter pipe all the way down to the base (using hands only) until it is tight. Use the filter wrench and turn the filter one- quarter turn more to seal it. Fill with motor oil. Find the engine oil fill on the valve cover and fill with the amount and kind of new engine oil specified in your owner's manual, usually 4-5 quarts. Cap the oil fill hole. Lower the car, then start it. Start the engine but do not rev it – just let it idle. Let the car run for about five minutes to warm up the engine and allow the oil to circulate. Check under the vehicle and make sure the filter is not leaking oil onto the pavement. Shut the engine off. Check the dipstick on the engine to make certain it reads "FULL."

      Answered on 4/2/2012 by John the Car-Doc from AAP
Displaying question 1

Do you have a question about this product? 

Check out the specials in our monthly flyer.
 
 
Disclaimer We strive to keep all information accurate and up-to-date; however, product availability, pricing, promotions and store hours are subject to change without notice. Please contact Customer Care if you have any questions or corrections.